Inhaltszusammenfassung zur Seite Nr. 1
Installation, Service and User Instructions
BUILT-IN GAS/ELECTRIC COOKTOP
BERTAZZONI
DIMENSIONS: 48’’(1216 mm) (W) x 25 1/8’’ (640mm) (D)
MODELs:
CTYK..U7X(2,5)A
310682
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT - PLEASE READ AND FOLLOW -Before beginning installation, please read these instructions completely and carefully. -Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. -Please observe all local and national codes and ordinances. -Please ensure that this product is properly grounded. -The installer should leave these instructions with the consumer who should retain for local inspector's use and for future reference. -The elec
Inhaltszusammenfassung zur Seite Nr. 3
WARNING Read this instruction booklet before installing and using the appliance. The manufacturer will not be responsible for any damage to property or to persons caused by incorrect installation or improper use of the appliance. The manufacturer reserves the right to make changes to its products when considered necessary and useful, without affecting the essential safety and operating characteristics. This appliance has been designed for non-professional, domestic use only. Warning: do
Inhaltszusammenfassung zur Seite Nr. 4
WARNING: Do not use aerosol sprays in the vicinity of this appliance while it is in operation Requirements Room ventilation – Location and venting. ATTENTION: An exhaust fan may be used with the appliance; in each case it shall be installed in conformity with the appropriate national and local standards. ATTENTION: Exhaust hood operation may affect other vented appliances; in each case it shall be installed in conformity with the appropriate national and local standards. INSTALLATION MA
Inhaltszusammenfassung zur Seite Nr. 5
ELECTRIC GRIDDLE INSTALLATION INSTRUCTIONS For installation the electric griddle, see the instructions indicated in the figure 5
Inhaltszusammenfassung zur Seite Nr. 6
INSTALLATION SIDE-BY-SIDE TO KITCHEN CABINET 1. This range may be installed directly adjacent to existing 36" (91.5 cm) high cabinets. IMPORTANT: The top border of the worktop should be at the same level of the adjacent cabinet countertop. This can be accomplished by raising the unit using the adjustment spindles on the legs. 2. The range CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other vertical surfaces above 36" (91.4 cm) high. There must be a
Inhaltszusammenfassung zur Seite Nr. 7
COOKER HOOD INSTALLATION The bottom of the hood should be 25 ½ " (65 cm) min. to 31 ½ " (80 cm) above the countertop. Refer to the rangehood installation instructions for additional information. These dimensions provide for safe and efficient operation of the hood. ELECTRICAL CONNECTION This unit is manufactured for a polarized, grounded 120 volt/60 Hz, 16 amp system. Electric power consumption is about 1080 W. The minimum of 102 VAC is required for proper operation of gas ignition s
Inhaltszusammenfassung zur Seite Nr. 8
Wiring diagram For freestanding gas range model CTYK..U7X(2,5)A CAUTION: label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. GAS CONNECTION All gas connections must be made according to national and local codes. TheThis gas supply (service) line must be the same size or greater than the inlet line of the appliance. This range uses a 1/2" NPTinlet (see fig. in this chapte
Inhaltszusammenfassung zur Seite Nr. 9
valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.45 kPa). 3. Flexible Connections: a) If the unit is to be installed with flexible couplings and/or quick disconnect fittings, the installer must use a heavy-duty, AGA design-certified commerciai flexible connector of at least 1/2" (1.3 cm) ID NPT (with suitable strain reliefs) in compliance with ANSI Z21.41 and Z21.69 standards. b) In Canada: CAN 1-6.10-88 metal con
Inhaltszusammenfassung zur Seite Nr. 10
- CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS: To change the nozzles of the burners use the following procedure: Lift up the burners and unscrew the nozzles ( Fig.) using an adjustable spanner of 7 mm and change the nozzles with those designed for the new gas supply according to the information given in TABLE shown below. Models CTYK..U7X(2, 5)A Adapting to different types of gas Burner Position Injector Gas Pressure Max Rate Min Rate By-pass diam. [mm.] T
Inhaltszusammenfassung zur Seite Nr. 11
REGULATION OF BURNERS Work surface burner adjustment: follow the instructions below to adjust the work surface burner minimum: 1) Light the burner and set the knob to the MINIMUM position (small flame). 2) Remove the knob of the valve that is press fit on the rod of that valve. 3) The cooker is equipped with safety valves, use a small slotted screwdriver the choke valve located on the valve body and turn the choke screw to the right or left until the burner flame is adjusted to minimum
Inhaltszusammenfassung zur Seite Nr. 12
Do not to cover the burners of cooktop with aluminium paper Keeping appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquid. Do not store dangerous or flammable material in the cabinet areas above appliance; store them in a safe place in order to avoid potential hazards. For safe use of appliance, do not use it for space heating. Do not use aerosol sprays in the vicinity of this appliance while it is in operation DESCRIPTIONS DESC
Inhaltszusammenfassung zur Seite Nr. 13
USING BURNERS A diagram is etched on the control panel above each knob which indicates which burner corresponds to that knob. (flame) Manual ignition: Manual ignition is always possible even when the power is cut off or in the event of prolonged power failure. Turn the knob that corresponds to the burner selected counterclockwise to the MAXIMUM position at the etched star (large flame) and place a lit match up to the burner. Automatic electric ignition: Turn the knob that correspond
Inhaltszusammenfassung zur Seite Nr. 14
USING THE ELECTRIC GRIDDLE WARNING The griddle element is hot after use. Allow sufficient time for griddle components cool before cleaning. The electric griddle element is rated 120 volts AC 1100 watts. Seasoning the griddle Before using the griddle for the first time, it must be seasoned. If the griddle has not been used for a period of time, it should be reseasoned. To season the gridlle: 1. clean the griddle thoroughly with hot, soapy water to remove any protective coating. 2.
Inhaltszusammenfassung zur Seite Nr. 15
CLEANING THE APPLIANCE: Never use abrasive cleaners Before cleaning the appliance it should be disconnected from the power supply. Cleaning the work surface: periodically clean the burner heads, the cast iron pan supports and the burner caps using warm water. Any spillage must always be removed as soon as possible using a rag. If it become difficult to open or close a valve, do not force it, but immediately request the assistance of the technical service personnel. Cleaning the enamelled
Inhaltszusammenfassung zur Seite Nr. 16
AFTER SALE SERVICE: Please note here below details for after save service. Refer to warranty certificate for warranty condiftions Dealer /Importer: Name, address, phone SERVICE CENTERS Name Phone MANUFACTURER: BERTAZZONI SPA VIA PALAZZINA, 8 – 42016 – GUASTALLA (
