Inhaltszusammenfassung zur Seite Nr. 1
OPERATING INSTRUCTIONS
CONTENTS
Safety Precautions
1
Setup & Installation
3
Controls
4
CAUTION!
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
Cable Setup
7
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
Platter Setup
8
Interchanging Tonearm Tubes
9
Tone Arm Setup 10
IMPORTANT
Cartridge Setup
11
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of un-insu
Inhaltszusammenfassung zur Seite Nr. 2
Thank you for purchasing this Numark product. Please read these operating instructions so you will know how to operate this equipment properly. After you have finished reading these instructions, keep them for future reference. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interfere
Inhaltszusammenfassung zur Seite Nr. 3
POWER-CORD PROTECTION Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. OUTDOORS ANTENNA GROUNDING If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges
Inhaltszusammenfassung zur Seite Nr. 4
SETUP & INSTALLATION This turntable has been designed exclusively for DJ use and can be setup in a variety of different ways depending on your mixing style. The turntable should rest on a level and stable surface that is clear of obstructions. If a mixer is placed between two turntables make sure that there is at least ¼" (7mm) between the mixer and the turntables to prevent damage to the turntables and to reduce unwanted system noise. Mixer Mixer 85 mm ¼" ¼" Setup
Inhaltszusammenfassung zur Seite Nr. 5
CONTROLS General Controls 1. Power Button This button turns on the turntable when pressed. It illuminates blue when the turntable is switched on. 2. Platter This turntable has a special edge design that has been optimized for "dragged" platter slow downs. (NOTE: The pattern will appear to stand still when the Pitch Range is set to 0% and the Target Light is being used.) 3. Start/Stop Buttons These buttons start and stop the turntable motor. Both buttons have the same function.
Inhaltszusammenfassung zur Seite Nr. 6
CONTROLS continued 9. Pitch Fader This slide control allows the pitch of the playback source to be changed. In the center position the pitch is at 0%. Moving the fader knob closer to you will increase the pitch. The Pitch Slider is enclosed in an Interchangeable/Replaceable Cartridge. 10. Pitch Button This button allows the turntable pitch range of the pitch fader to be adjusted. 11. Quartz Button This button locks the pitch at 0% using Quartz Motor Control when it is pressed.
Inhaltszusammenfassung zur Seite Nr. 7
CONTROLS continued Bottom Parts 20. Adjustable Rubber Dampening Feet When all of the feet of the turntable are completely tightened, the top flat surface of the turntable will be at 85mm. Unscrewing these feet raises the turntable up to compensate for unleveled surfaces. 21. Carrying Handles These handles provide a secure grip so that the turntable may be comfortably transported. 22. Voltage Selector This switches the internal voltage transformer between 115V, 230V and 240V. The
Inhaltszusammenfassung zur Seite Nr. 8
CABLE SETUP This turntable is shipped with two sets of special cables: (1) Right Angle IEC Power Cord (1) Right Angle RCA cord NOTE: Before connecting any cables, make sure that the voltage selector switch is set to the proper setting! Making the power and audio connections: 1. Begin by lifting the turntable up from the rear handle and resting it on its side. (NOTE: The turntable must be supported because it is not stable in this position!) 2. Next connect the Red Right A
Inhaltszusammenfassung zur Seite Nr. 9
PLATTER SETUP WARNING: Incorrect Platter setup can lead to poor turntable performance, platter instability, or permanent motor damage. 1. Start by inspecting the bottom of the aluminum platter to check that both locking pins have rubber fittings on them. 2. Next, rotate the platter spindle so that two holes are aligned parallel with the front of the turntable. 3. Carefully install the platter onto the center spindle and motor assembly making sure that the Numark logo and the two h
Inhaltszusammenfassung zur Seite Nr. 10
INTERCHANGING TONEARM TUBES WARNING: An incomplete understanding of this procedure could lead to permanent damage to the headshell, your records, or the tonearm assembly. NOTICE: Interchanging tonearm tubes unnecessarily may shorten the life of the tonearm tubes and/or tonearm components. This turntable features the world's only tonearm assembly capable of accommodating two different tonearm tube styles: S-Shaped and Straight. The S-Shaped tube produces a higher signal to noise rat
Inhaltszusammenfassung zur Seite Nr. 11
TONE ARM SETUP A properly adjusted tone arm and cartridge setup will minimize vinyl record wear and optimize the performance of the turntable. Follow these simple steps for setting the tone arm on the turntable: NOTE: In most cases, when using the S-Shaped tonearm tube, the additional S-Weight must be fastened to the tonearm to achieve proper stylus pressure.Balancing the Tone Arm 1. Begin the balancing process by lifting the cue lever to the up position (or make sure that the stylus
Inhaltszusammenfassung zur Seite Nr. 12
CARTRIDGE SETUP For Head Shell Mounted Cartridges: The cartridge that comes with this turntable should be preinstalled on the head shell. If it isn't, please follow the below instructions for installing a cartridge onto the head shell. 1. Position the head shell and the cartridge so that the four connector pins are visible. Make sure that the stylus cover is installed to prevent damage to the stylus during installation. 2. Prepare to connect the cartridge to the head shell using th
Inhaltszusammenfassung zur Seite Nr. 13
OTHER IMPORTANT NOTES Please read these precautionary notes to insure a complete understanding and long life of this DJ turntable. 1. Unnecessarily removing the platter may cause damage to the magnet mounting structure, the motor or the platter resulting in undesired performance. The turntable should ALWAYS be powered off before the turntable platter is removed for any reason. 2. Repeatedly "interchanging" tonearm tubes may cause premature wear to components of the tonearm assembly
Inhaltszusammenfassung zur Seite Nr. 14
SPECIFICATIONS Turntable: Torque (transient): 4.5kgf.cm Torque (stable): 3.5kgf.cm Motor: Brushless DC motor Brake: Electronic braking system Platter: Dampened aluminum diecast, low friction design Pitch: +/-8%, 10%, 25%, 50% Speeds: 33 1/3RPM, 45RPM, 78RPM Wow/flutter: <0.15% max, <0.10% typical Tonearm: Patented locking collar-based interchangeable tube system Diecast aluminum 3-bearing construction Height range: 0-6mm Cue System: Dampened lift lever Arm rest and ar
Inhaltszusammenfassung zur Seite Nr. 15
Problem Cause? Solution Turntable does not turn on. Disconnected Power Cord? Connect Power Cord. The sound level is very low. The Turntable is not connected to a Connect the device to a preamp DJ device with a PHONO preamp. mixer or an AV receiver that has an input labeled PHONO. The sound is on one side only. The Cartridge is not properly wired. Reconnect the wires from the headshell to the cartridge. See the "Cartridge Setup" section for more detail. The Stylus is worn out. Replace the sty
Inhaltszusammenfassung zur Seite Nr. 16
INSIDE THE BOX: (1) Turntable w/Straight (1) Anti-Drag (1) Slipmat Tonearm Aluminum Platter (1) Counter Weight (1) Target Light (1) Headshell (1) 45 RPM Adapter (1) S-Shaped Tonearm (1) S-Tube Tonearm (1) Service Tool Tube Weight (1) IEC Power Cable (1) RCA Cord
