Inhaltszusammenfassung zur Seite Nr. 1
Jiva Series
Optional Attachment Kits
User’s Manual
Rev. Original
KP100
SD100
SD200
FCC Notes:
PD302
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection
Inhaltszusammenfassung zur Seite Nr. 2
GENERAL DESCRIPTION OVERVIEW This manual covers side mount attachment upgrade kits KP100, SD100, SD200 and the rear top mount attachment kit PD302 for Posiflex Jiva series terminals and the extended side mount attachment kits KP110/SD110/SD210 for the touch monitor TM4115. The rear top mount kit PD302 is a 2 line by 20 (6.0 x 9.66 mm) easy viewing characters LCD customer display. The side mount kits KP’s and SD’s provide flexible configuration of optional security devices with interfac
Inhaltszusammenfassung zur Seite Nr. 3
INSTALLATION 1. HARDWARE INSTALLATION A FOR SIDE MOUNT KIT (KP or SD) Mechanical Mounting For the side mount integrated attachment kits (KP100, KP110, SD100, SD110, SD200, SD210) ordered with the host system like Jiva series or TM4115 series, it is installed on the system at delivery. For separately ordered side mount kit, it is delivered separately from the system and needs to be fixed onto the system (however, SD200 series for Jiva 5800 series before the Jiva 5800G version is not re
Inhaltszusammenfassung zur Seite Nr. 4
is selected. Route the cable connection for the attachment kit to cable cover area of Jiva series or TM4115 through the side of the cable cover. Break the obstructing side wall of the cable cover in the cable entrance to the connector area according to the needs. Connection To PS/2 Keyboard PS/2 KB Connector KP100 Rear View KP100 Inclined Bottom View Indentation For Cable Holding Refer to the pictures of bottom of KP100 with their partially enlarged pictures to the r
Inhaltszusammenfassung zur Seite Nr. 5
from the TP series. Please remove the COM1 terminator and save it at a safe place for future use if COM1 is to be used for PD302. 4. Route the cable to go through the notch on back of the stand assembly of touch terminal as indicated in the picture. Reassemble the main unit and stand assembly. (Guidance for future un-installation: Please use screw driver to release the metal hook before removing PD302 from the ventilation holes.) 2. DRIVER INSTALLATION 1. For MSR: The magnetic stripe r
Inhaltszusammenfassung zur Seite Nr. 6
layout appearance when required. The content of the programmable keys should have been organized by the system integrator and requires no installation by end users. Please use a flattop (minus sign) screw driver (Do not use the attached key clip for this operation.) to help getting the key top off gently if change for blank key or double key is required. Please always first orientate the key tops correctly before inserting any key top into the case of the keypad. Failure to do so could
Inhaltszusammenfassung zur Seite Nr. 7
US LF <1F><0A> Move Cursor Up US CR <1F><0D> Move Cursor To Right Most Position Move Cursor To Specified Position US $ <1F><24> n = 1 ~ 20 m = 1, 2 US @ <1F><40> Show Version US B <1F><42> Move Cursor To Bottom Position US C <1F><43> Cursor On / Off, n = 1, 0 Blink Display Screen US E <1F><45> n = 0 ~ 255 PST COMMAND MODE: HEX CODE FUNCTION <01> Set Pass Through Flag (should not be used) <06> Change Leading Code 1 2 <14> <01> Wraparound Mode (Default) <14>
Inhaltszusammenfassung zur Seite Nr. 8
OPERATION GUIDE E-M TYPE FINGER PRINT SENSOR The Posiflex E-M type finger print sensor has been tested to operate well on reading finger prints of various skin conditions, it is still advisable to keep the scanning area clean. To have a successful scanning, the finger must be placed in a way that the core of the finger print is within the scanning area (and best be in the center of the area), the finger should align with the sensing pad within a tolerance of +/- 15º and the finger must
Inhaltszusammenfassung zur Seite Nr. 9
and apply gentle, even pressure. Do not “roll” your finger as usually practiced in the traditional ink and paper fingerprint taking technique. Pressing too hard will distort your fingerprint. Pressing too lightly will not expose a large enough area of your finger. Also, make sure to hold your finger on the sensor until you see the sensor light blink; this may take longer for dry fingers. Then, lift your finger. Although you may use any finger with the sensor, your index finger of either
Inhaltszusammenfassung zur Seite Nr. 10
program covers each track enable/disable, Alt+Num approach for ASCII codes and Leading/Stop code enable/disable. The function for enabling each track of course comes in effect only when the track is physically available. Please find in the mini CD delivered with SD200 or Product Information CD delivered with Posiflex POS system the folder for “USBMSR” and “SetUp” this demo program or download the installation program from our web sites http://www.posiflex.com or http://www.posiflex.com.t
