Inhaltszusammenfassung zur Seite Nr. 1
Porto-Power Blackhawk Automotive is a licensed trademark
Porto-Power Kit
Operating Instructions & Parts Manual
U.S. PATENT 5,520,400
Model Number Capacity
B65114 4 Ton
B65115 10 Ton
SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153
816-891-6390
sales@blackhawk-automotive.com
- Before using this product, read this manual and follow all its Safety Rules and Operating Instructions
Made in China
B65114-M0 rev 11/05
Inhaltszusammenfassung zur Seite Nr. 2
ONE YEAR LIMITED WARRANTY For a period of one (1) year from date of purchase, SFA Companies will repair or replace, at its option, without charge, any of its products which fails due to a defect in material or workmanship under normal usage. This limited warranty is a consumer's exclusive remedy. Performance of any obligation under this warranty may be obtained by returning the warranted product, freight prepaid, to SFA Companies Warranty Service Department, 10939 N. Pomona Ave., Kansas City, MO
Inhaltszusammenfassung zur Seite Nr. 3
SAVE THESE INSTRUCTIONS For your safety, read and understand the information contained within. The owner and operator shall have an under- standing of this product and safe operating procedures before attempting to use this product. Instructions and Safety information shall be conveyed in the operator's native language before use of this product is authorized. Make certain that the operator thoroughly understands the inherent dangers associated with the use and misuse of the product. If any doub
Inhaltszusammenfassung zur Seite Nr. 4
SAFETY INSTRUCTIONS BEFORE USE (Refer to Figure 1 on page 3) 1. Study, understand, and follow all instructions provided with and on this device before use. 2. Inspect before each use. Do not use if bent, broken, leaking or damaged components are noted. 3. Ensure that product and application are compatible. 4. Check to ensure that all parts of your kit are included (see illustration and parts list on page 10 & 11). 5. Carefully remove the dust covers and plugs from hose coupler and ram coupler. 6
Inhaltszusammenfassung zur Seite Nr. 5
! ! WARNING WARNING ! Hydraulic Hoses and Fluid Transmission Lines • Ram must be on a stable base, which is able to • Avoid short runs of straight line tubing. Straight line support the load while pushing or lifting. runs do not provide for expansion and contraction due • Ensure ram is fully engaged into/onto adapters, to pressure and/or temperature changes. extension accessories. • Reduce stress in tube lines. Long tubing runs should • To help prevent personal injury, use shims, friction be s
Inhaltszusammenfassung zur Seite Nr. 6
OPERATION Note: Inspect before each use for evidence of fluid leaks, damaged hydraulic fittings, bent or broken attachments and missing parts. 1. Locate and close release valve by turning it clockwise until firmly closed. (Do not over tighten) 2. Operate by pumping handle. This will send fluid from the pump reservoir into the high pressure hose assembly and into the ram assembly. 3. Continue pumping until ram reaches desired height. Note: Pump may be used in horizontal and vertical position as i
Inhaltszusammenfassung zur Seite Nr. 7
Basic Setup The capacity of the Porto-Power Kit can be significantly affected by the number of attachments used and the type of load applied. The approximate load capacity of each function setup is illustrated below. When two or more extension tubes are used together, be sure to position the shortest tube further away from the ram. Note: Not all accessories in the illustrations provided in the Porto-Power Kit. A. Push & Stretch Serrated Saddle Male Flat Base Connector 100% Ram Ram Rubber Head Ma
Inhaltszusammenfassung zur Seite Nr. 8
TROUBLESHOOTING Symptom Possible Causes Corrective Action Ram will not extend • Release valve not tightly closed • Ensure release valve tightly closed • Overload condition • Remedy overload condition Ram will not lift to full extension • Fluid level low • Ensure proper fluid level Spongy effect • Air trapped in system • Bleed air from system Ram *bleeds off after lift • Release valve not tightly closed • Ensure release valve tightly closed • Dirt in pump's return check valve • Flush the system •
Inhaltszusammenfassung zur Seite Nr. 9
Replacement Parts for Model B65114 Item # Part # Description Qty. 1 B65161 Extension Tube (19-1/2") 1 2 B65160 Extension Tube (16-1/2") 1 3 B65159 Extension Tube (8-1/2") 1 4 B65158 Extension Tube (6-1/8") 1 5 B65157 Extension Tube (3") 1 6 B65177 Male connector 1 7 B65153 Wedge Head (offset) 1 8 B65151 Serrated Saddle 1 9 B65156 Flat Base 1 10 B65154 Plunger Toe (offset) 1 11 B65155 Ram Toe (offset) 1 12 B65178 Rubber Head 1 0 13 B65152 Combination Head 90 1 14 B65123 1/2 Ton Spreader 1 15 434-
Inhaltszusammenfassung zur Seite Nr. 10
Replacement Parts for Model B65115 Item# Part# Description Qty. 1 B65162 Extension Tube (27") 1 2 B65163 Extension Tube (18") 1 3 B65164 Extension Tube (10") 1 4 B65165 Extension Tube (4") 1 5 B65179 Male Connector 1 6 B65166 Wedge Head (offset) 1 7 B65167 Serrated Saddle 1 8 B65168 Flat Base 1 9 B65172 Plunger Toe (offset) 1 10 B65169 Ram Toe (offset) 1 11 B65180 Rubber Head 1 o 12 B65173 Combination Head 90 1 13 B65123 1/2 Ton Spreader 1 14 434-6-3313-101 Dust Cover - Hose 1 15 434-6-3312-109
Inhaltszusammenfassung zur Seite Nr. 11
Load - Pressure Correlation For Model B65114 & B65115 Always monitor the force applied to workpiece by using a load cell and indicator or you may monitor pressure developed in the ram by using an inline pressure gauge, then calculate the applied force using the formula: where F = Force/ Load (lbs); P = Hydraulic working pressure (psi) and; F = P x A A = Ram effective area (in²) For model B65114, A = 0.998 in² ; For model B65115, A = 2.411 in² Example1 Example2 Model B65114 lif
Inhaltszusammenfassung zur Seite Nr. 12
memo.
