Inhaltszusammenfassung zur Seite Nr. 1
•• •••• •••• •••• ••• •••• •••• •
Barracuda 4LP
•• •••• •••• •••• ••• •••• •••• •
Disc Drive
•• •••• •••• •••• ••• •••• •••• •
ST34371N/W/WC/WD/DC
•• •••• •••• •••• ••• •••• •••• •
ST32171N/W/WC/WD/DC
•• •••• •••• •••• ••• •••• •••• •
ST34571N/W/WC/WD/DC
•• •••• •••• •••• ••• •••• •••• •
ST32271N/W/WC/WD/DC
•• •••• •••• •••• ••• •••• •••• •
Installation Guide
Inhaltszusammenfassung zur Seite Nr. 2
Contents Preface ........................................................................................1 Electrostatic discharge protection................................................1 Important safety information and precautions..............................2 Wichtige Sicherheitshinweise ......................................................4 European Union Compliance.......................................................7 Technical support services........................................
Inhaltszusammenfassung zur Seite Nr. 3
Barracuda 4LP Installation Guide, Rev. B 1 Preface This manual contains information for users of the Seagate® Barracuda 4LP SCSI disc drives. It provides support services, performance specifications, and initial setup information. Addi- tional information is available in the Barracuda 4LP Product Manual (part number 77767491). Contact your Seagate sales representative if you need to order this publication. Electrostatic discharge protection Caution. Removal of circuit boards by personnel not per
Inhaltszusammenfassung zur Seite Nr. 4
2 Barracuda 4LP Installation Guide, Rev. B • Turn off the power before removing or installing the DC power cable. • Do not remove any circuit boards from the drive. • Never use an ohmmeter on any circuit boards. • When installing the drive on a carrier or tray, discharge the carrier or tray prior to inserting it into the system. Important safety information and precautions Caution. Use forced-air ventilation when bench-testing the drive to ensure proper cooling of drive components. Use proper sa
Inhaltszusammenfassung zur Seite Nr. 5
Barracuda 4LP Installation Guide, Rev. B 3 stacked vertically, pay special attention to the top where tem- peratures are usually highest. • Follow the precautions listed above in “Electrostatic discharge protection.” • Do not remove any circuit boards from the drive. Return the entire drive for depot repair if any circuit board is defective. Removal of circuit boards by personnel not performing depot repair will damage components and may void the warranty. • Do not remove the head and disc assem
Inhaltszusammenfassung zur Seite Nr. 6
4 Barracuda 4LP Installation Guide, Rev. B This unit is a component part and as such is not meant to comply with FCC or similar national requirements as a stand-alone unit. Engineering radiated emissions test results are available through the Seagate Safety Department to assist the subsystem designer. Wichtige Sicherheitshinweise Vorsicht. Beim Testen des Laufwerks auf dem Prüftisch ist Fremdbelüftung vorzusehen, um eine ausreichende Kühlung der Laufwerkkomponenten sicherzustellen. Verwenden Sie
Inhaltszusammenfassung zur Seite Nr. 7
Barracuda 4LP Installation Guide, Rev. B 5 Beachten Sie in jedem Fall die folgenden Warn-und Vorsicht- shinweise: • Beachten Sie alle Warn- und Vorsichtshinweise in diesem Handbuch. • Treffen Sie beim Betrieb, bei der Installation oder bei der Entfernung der Einheit angemessene Sicherheitsvorkehrun- gen. • Wenn eine Einheit unter Spannung steht, gehen Sie bei der Fehlerdiagnose besonders vorsichtig vor. Schalten Sie die Einheit aus, bevor Sie mit den Installations-und Entfernung- sarbeiten begin
Inhaltszusammenfassung zur Seite Nr. 8
6 Barracuda 4LP Installation Guide, Rev. B • Die vormontierte Kopf- und Festplatteneinheit (HDA) nicht aus dem Laufwerk nehmen! Falls die HDA beschädigt ist, schicken Sie das gesamte Laufwerk zur Reparatur ein. • Die HDA ist nicht vor Ort reparierbar und darf nicht auseinan- dergenommen werden! Öffnen der versiegelten HDA durch andere Personen als die für die werkseitige Reparatur zustän- digen hat eine Beschädigung der Komponenten und Erlöschen des Garantieanspruchs zur Folge. Als Teilkomponen
Inhaltszusammenfassung zur Seite Nr. 9
Barracuda 4LP Installation Guide, Rev. B 7 magnetische Strahlung sind für Designer von Untersystemen auf Anfrage von der Seagate-Sicherheitsabteilung erhältlich. European Union Compliance If this model has the CE Marking, it complies with the European Union requirements of the Electromagnetic Compatibility Direc- tive 89/336/EEC of 03 May 1989 as amended by Directive 92/ 31/EEC of 28 April 1992 and Directive 93/68/EEC of 22 July 1993. Seagate uses an independent laboratory to confirm compliance
Inhaltszusammenfassung zur Seite Nr. 10
8 Barracuda 4LP Installation Guide, Rev. B Technical support services If you need assistance installing your drive, consult your dealer. Dealers are familiar with their unique system configurations and can help you with system conflicts and other technical issues. If ® you need additional assistance with your Seagate drive or other Seagate products, use one of the Seagate technical sup- port services listed below. ® SeaFONE at 1-800-SEAGATE (1-800-732-4283) Seagate’s 800 number allows toll-free
Inhaltszusammenfassung zur Seite Nr. 11
Barracuda 4LP Installation Guide, Rev. B 9 ® SeaBOARD SeaBOARD is a computer bulletin board system (BBS) that con- tains information about Seagate’s disc and tape drive products and is available 24 hours daily. Set your communications soft- ware to eight data bits, no parity, and one stop bit (8-N-1). Sea- BOARD phone numbers are listed in the following table. BBS Location Modem number United States Disc: 408-434-1080; Tape: 408-456-4415 England 44-1628-478011 France 33 1-48 25 35 95 Germany 49
Inhaltszusammenfassung zur Seite Nr. 12
10 Barracuda 4LP Installation Guide, Rev. B Seagate Technology FAX services ® SeaFAX You can use a touch-tone telephone to access Seagate’s auto- mated FAX system to receive technical support information by return FAX. This service is available 24 hours daily. Location Telephone number United States 1-800-SEAGATE or 408-456-4496 England 44-1628-894084 Australia 61-2-9756-5170 Seagate technical support FAX You can FAX questions or comments to technical support spe- cialists 24 hours daily. Respon
Inhaltszusammenfassung zur Seite Nr. 13
Barracuda 4LP Installation Guide, Rev. B 11 Before calling, note your system configuration and drive model number (STxxxx). There are several technical support phone numbers available for various Seagate products. Location Telephone number United States Please dial 1-800-SEAGATE for the specific product telephone number. (6:00 A.M. to 11:15 A.M., 12:30 P.M. to 5:00 P.M., M–F) England 44-1628-894083 (10:00 A.M. to 1:00 P.M., 2:00 P.M. to 5:00 P.M., M–F) France 33 1-41 86 10 86 (9:30 A.M. to 12
Inhaltszusammenfassung zur Seite Nr. 14
12 Barracuda 4LP Installation Guide, Rev. B General description Barracuda 4LP SCSI disc drives are high-speed, random-access digital-data storage devices. The drive is a component for installation in an enclosure designed for the drive. This is often a rack within the system or an external enclosure designed to house one or more disc drives or other peripheral units. In either case, the disc drive must receive adequate cooling (refer to “Providing adequate cooling”) and it must be sufficiently
Inhaltszusammenfassung zur Seite Nr. 15
Barracuda 4LP Installation Guide, Rev. B 13 Table 1. Drive characteristics Interface UltraSCSI [1] Capacity Formatted [2] Unformatted ST34371 4.35 Gbyte [2] 5.31 Gbyte ST32171 2.16 Gbyte [2] 2.65 Gbyte ST34571 4.55 Gbyte [2] 5.54 Gbyte ST32271 2.26 Gbyte [2] 2.77 Gbyte Recording Cylinders (user) 5,178 Read/write data heads ST32171/ST32271 5 ST34371/ST34571 10 Access time [3] Average read 9.4 msec Average write 10.4 msec Disk rotation RPM 7,200 r/min Average latency 4.17 msec Internal transfer ra
Inhaltszusammenfassung zur Seite Nr. 16
14 Barracuda 4LP Installation Guide, Rev. B [2] Standard factory units are formatted 512 data bytes per sector with sparing equivalent to eighty spare sectors per eight cylinder region. Spares are located at the end of each sparing region. [3] Includes controller overhead. Table 2a. DC power requirements (Amps) ST34371/ST34571 N/W/WC WD/DC Single-ended Differential Voltage +5V +12V +5V +12V Regulation [5] ±5% ±5%[2] ±5% ±5%[2] Max. operating current DC3σ [1] 0.81 0.95 1.21 0.95 Avg. idle current
Inhaltszusammenfassung zur Seite Nr. 17
Barracuda 4LP Installation Guide, Rev. B 15 Table 2b. DC power requirements (Amps) ST32171/ST32271 N/W/WC WD/DC Single-ended Differential Voltage +5V +12V +5V +12V Regulation [5] ±5% ±5%[2] ±5% ±5%[2] Max. operating current DC3σ [1] 0.81 0.85 1.21 0.85 Avg. idle current DCX [1] 0.46 0.52 0.70 0.52 Max. starting current (peak DC) DC3σ [3] 0.78 2.00 1.1 2.00 (peak AC) AC3σ [3] 3.1 3.1 Delayed motor start (max) DC3σ [1][4] 0.50 0.20 0.90 0.20 Peak operating current Typical DCX [1][6] 0.72 0.73 0.91
Inhaltszusammenfassung zur Seite Nr. 18
16 Barracuda 4LP Installation Guide, Rev. B [5] See “Conducted noise immunity” in the Barracuda 4LP Prod- uct Manual. The specified voltage tolerance is inclusive of ripple, noise, and transient response. [6] Operating condition is defined as random seek read opera- tions with a block count of 64. General Notes from Tables 2a and 2b. 1. Minimum current loading for each supply voltage is not less than 4% of the maximum operating current shown. 2. Use separate ground returns for +5V and +12V suppl
Inhaltszusammenfassung zur Seite Nr. 19
Barracuda 4LP Installation Guide, Rev. B 17 Initial setup information The general information beginning on this page applies to all of the Barracuda 4LP drive models. After reading the general infor- mation topics, refer to the appropriate drive-specific section listed below for additional information about configuring and installing your particular model. Drive models Page ST32171N ST32271N ST34371N ST34571N 36 ST32171W/WD ST32271W/WD ST34371W/WD ST34571W/WD 40 ST32171WC/DC ST32271WC/DC ST34371
Inhaltszusammenfassung zur Seite Nr. 20
18 Barracuda 4LP Installation Guide, Rev. B SCSI ID jumpers Each device on the SCSI chain must have a unique SCSI ID. The host system’s SCSI controller usually uses the ID that has the highest priority interrupt in the SCSI I/O system. This is always ID7. ID0 is lowest priority in an 8-bit I/O system. ID8 is lowest priority in a 16-bit I/O system. The lower priority SCSI IDs are normally used for other SCSI devices such as this Barracuda disc drive. Note. Most SCSI controllers (host adapters) al
