Inhaltszusammenfassung zur Seite Nr. 1
Angular Style Air Gripper
Toggle Type
Series MHT2
MHZ
MHF
MHL
MHR
MHK
MHS
MHC
MHT
MHY
MHW
MRHQ
Misc.
D-
20-
12-9-1
Inhaltszusammenfassung zur Seite Nr. 2
Angular Style Air Gripper Toggle Type Series MHT2 Size: 32, 40, 50, 63 How to Order Ideal for gripping heavy workpiece. MHT2 32 D F9BW S The toggle mechanism Toggle type Number of auto Auto switch air gripper holds workpiece even switches Without auto switch when pressure drops. Number of fingers Nil 2 pcs. Nil (Built-in magnet) S 1 pc. 2 2 fingers Auto switch is ∗ For the applicable auto n “n” pcs. Bore size switch model, refer to the attachable. table below. 32 mm 32 40 mm 40 Action 50
Inhaltszusammenfassung zur Seite Nr. 3
Angular Style Air Gripper Toggle Type Series MHT2 Effective Gripping Force • Workpiece gripping point should be within the L = 100 mm MHT2-32D range indicated in the graph. MHZ Pressure 0.6 MPa 0.4 MPa MHF 0.2 MPa MHL Opening/Closing angle (Both sides) MHR L = 120 mm MHT2-40D MHK MHS • Indication of effective gripping force MHC The effective gripping force shown in the graphs to the right is expressed as F, which is MHT the thrust of one finger, when both fingers and Pressure 0.6 MPa atta
Inhaltszusammenfassung zur Seite Nr. 4
Series MHT2 Dimensions 8-M6 x 1 mounting thread Thread depth 10 (Both sides) MHT2-32D 4-M6 x 1 thread depth 10 Mounting thread Finger closing port Rc 1/8 Finger opening port Rc 1/8 4-M6 x 1 thread depth 15 Mounting thread 4-M6 x 1 bottom hole dia. 5.1 Thread for mounting attachment MHT2-40D 8-M8 x 1.25 mounting thread Thread depth 10 (Both sides) 4-M6 x 1 thread depth 10 Mounting thread Finger closing port Rc 1/8 Finger opening port Rc 1/8 4-M8 x 1.25 thread depth 12 Mounting thread 4-M8 x 1.25
Inhaltszusammenfassung zur Seite Nr. 5
Angular Style Air Gripper Toggle Type Series MHT2 Dimensions MHT2-50D 8-M10 x 1.5 mounting thread Thread depth 12 (Both sides) 4-M8 x 1.25 thread depth 14 Mounting thread MHZ MHF MHL MHR MHK Finger closing port MHS Rc 1/4 Finger opening port MHC Rc 1/4 MHT MHY 4-M10 x 5 bottom hole dia. 8.6 4-M10 x 1.5 thread depth 12 MHW Thread for mounting attachment Mounting thread MRHQ MHT2-63D Misc. D- 8-M12 x 1.75 mounting thread Thread depth 17 (Both sides) 20- 4-M10 x 1.5 thread depth 18 Mounting thread
Inhaltszusammenfassung zur Seite Nr. 6
Series MHT2 Construction Component Parts No. Description Material Note q Side plate Aluminum alloy Hard anodized w Finger Carbon steel Black zinc chromated e Lever Carbon steel Black zinc chromated Carbon steel Black zinc chromated r Joint t Shaft Stainless steel Joint pin Stainless steel y Cylinder plate Soft steel Black zinc chromated u i Lever pin Stainless steel Bearing Steel lined oil imfilled acetal resin bearing o Cylinder Compact cylinder !0 Replacement Parts Description MHT2-32D MHT2-40
Inhaltszusammenfassung zur Seite Nr. 7
Angular Style Air Gripper Toggle Type Series MHT2 Mounting of Auto Switch Auto Switch Hysteresis Rail mounting type MHZ MHF MHL MHR MHK Hysteresis Switch operating position (ON) MHS Switch reset position (OFF) MHC Model Hysteresis (Max.) angle MHT MHT2-32D 3 MHT2-40D 3 MHY MHT2-50D 3 MHT2-63D 3 MHW Direct mounting type MRHQ Misc. D-A7, D-A8: Rail mounting type . D-M9V: Direct mounting type are shown above. D- Rail mounting Direct mounting 20- D-A7H/A80H D-A73C/A80C D-M9 D-F7BAL/F7BAVL D-M9V
Inhaltszusammenfassung zur Seite Nr. 8
Series MHZ2/MHZJ2/MHK2/MHKL2/MHC2/MHT2 Auto Switch Installation Example and Mounting Position Various auto switch applications are possible through different combinations of auto switch quantities and detecting positions. 1) Detection when Gripping Exterior of Workpiece 1. Confirmation of fingers in 2. Confirmation of workpiece held 3. Confirmation of workpiece released Detection example reset position Position of Position Position of Position to be fingers fully when fingers fully detected o
Inhaltszusammenfassung zur Seite Nr. 9
Auto Switch Various auto switch applications are possible through different combinations of auto switch quantities and detecting positions. 2) Detection when Gripping Interior of Workpiece 1. Confirmation of fingers in reset 2. Confirmation of workpiece held 3. Confirmation of workpiece released Detection example position Position of Position Position of Position to be MHZ fingers when fingers fully detected fully gripping opened closed MHF Switch turned ON when fingers return. Switch turned O
Inhaltszusammenfassung zur Seite Nr. 10
Safety Instructions These safety instructions are intended to prevent a hazardous situation and/or equipment damage. These instructions indicate the level of potential hazard by labels of Note 1) "Caution", "Warning" or "Danger". To ensure safety, be sure to observe ISO 4414 , Note 2) JIS B 8370 and other safety practices. Operator error could result in injury or equipment damage. Caution : Operator error could result in serious injury or loss of life. Warning : In extreme conditions, ther
Inhaltszusammenfassung zur Seite Nr. 11
Common Precautions Be sure to read before handling. For detailed precautions on every series, refer to main text. 4. Use clean air Selection If the compressed air supply is contaminated with chemicals, cynthetic materials, corrosive gas, etc., it may lead to break Warning down or malfunction. 1. Confirm the specifications. Products represented in this catalog are designed for use in Operating Environment compressed air appllications only (including vacuum), unless otherwise indicated. Warnin
Inhaltszusammenfassung zur Seite Nr. 12
Quality Assurance Information (ISO 9001, ISO 14001) Reliable quality of products in the global market To enable our customers throughout SMC’s quality control system the world to use our products with Make customers our even greater confidence, SMC has first priority, offering them reliable and Create new products using the friendly service. obtained certification for international latest technology, and offer the finest standards “ISO 9001” and “ISO Produce the highest products in a
Inhaltszusammenfassung zur Seite Nr. 13
SMC Product Conforming to Inter SMC products complying with EN/ISO, CSA/UL standards are supporting CE Mark The CE mark indicates that machines and components meet essential requirements of all the EC Directives applied. It has been obligatory to apply CE marks indicating conformity with EC Directives when machines and components are exported to the member Nations of the EU. Once “A manufacturer himself” declares a product to be safe by means of CE marking (declaration of conformity by manu
Inhaltszusammenfassung zur Seite Nr. 14
SMC Product Conforming to International Standards national Standards you to comply with EC directives and CSA/UL standards. Mark of compliance Mark of compliance for CSA/UL for CSA CSA Standards & UL Standards UL and CSA standards have been applied in North America (U.S.A. and Canada) symbolizing safety of electric products, and are defined to mainly prevent danger from electric shock or fire, resulting from trouble with electric products. Both UL and CSA standards are acknowledged in North
Inhaltszusammenfassung zur Seite Nr. 15
SMC’s Global Service Network America Europe U.K. SMC Pneumatics (U.K.) Ltd. U.S.A. SMC Corporation of America Vincent Avenue, Crownhill, Milton Keynes, MK8 0AN, Backinghamshire, U.K. 3011 North Franklin Road Indianapolis, IN 46226, U.S.A. TEL: 01908-563888 FAX: 01908-561185 TEL: 317-899-4440 FAX: 317-899-3102 CANADA SMC Pneumatics (Canada) Ltd. GERMANY SMC Pneumatik GmbH 6768 Financial Drive Mississauga, Ontario, L5N 7J6 Canada Boschring 13-15 D-63329 Egelsbach, Germany TEL: 905-812-0400
Inhaltszusammenfassung zur Seite Nr. 16
SMC’s Global Service Network Europe Oceania/Asia FINLAND SMC Pneumatics Finland OY AUSTRALIA SMC Pneumatics (Australia) Pty.Ltd. PL72, Tiistinniityntie 4, SF-02231 ESP00, Finland 14-18 Hudson Avenue Castle Hill NSW 2154, Australia TEL: 09-8595-80 FAX: 09-8595-8595 TEL: 02-9354-8222 FAX: 02-9894-5719 NORWAY SMC Pneumatics Norway A/S NEW ZEALAND SMC Pneumatics (New Zealand) Ltd. Vollsveien 13C, Granfoss Næringspark N-1366 LYSAKER, Norway 8C Sylvia Park Road Mt.Wellington Auckland, New Zealan
