Inhaltszusammenfassung zur Seite Nr. 1
OWNER’S OPERATING MANUAL
CR-32HD / CR-40HD
with
Crystal Series™ LCD Displays
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents One Year Limited Warranty ......................................................................4 Introduction ...............................................................................................7 Precautions ...............................................................................................8 Control Panels CR-32HD and CR-40HD Front View ................................................................................ 9 CR-32HD Rear View and Input Panel ..
Inhaltszusammenfassung zur Seite Nr. 3
ISF Calibration (Service) Picture Adjust .................................................................................................................. 25 White Balance ................................................................................................................. 25 Blue Enable ..................................................................................................................... 26 DNR .........................................................................
Inhaltszusammenfassung zur Seite Nr. 4
One Year Limited Warranty Congratulations on your purchase of Runco’s latest video product and welcome to the Runco family! We believe Runco produces “The World’s Finest Home Theater Products”. With proper installation, setup and care, you should enjoy many years of unparalleled video performance. This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your other important documents. WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED
Inhaltszusammenfassung zur Seite Nr. 5
This Limited Warranty only covers failure due to defects in materials and workmanship that occur during normal use and does not cover normal maintenance. This Limited Warranty does not cover cabinets or any appearance items; failure resulting from accident, misuse, abuse, neglect, mishandling, misapplication, faulty or improper installation or setup adjustments; improper maintenance, alteration, improper use of any input signal; damage due to lightning or power line surges, spikes and browno
Inhaltszusammenfassung zur Seite Nr. 6
ADDITIONAL INFORMATION: To locate the name and address of the nearest Runco Authorized Service Center, or for additional information about this Limited Warranty, please call or write: RUNCO INTERNATIONAL, INC. Attn: Customer Service Department 2900 Faber Street Union City, CA 94587 Ph: (510) 324-7777 Fax: (510) 324-9300 Toll Free: (800) 23-RUNCO RUNCO VIDEO PRODUCT INFORMATION RETAIN THIS INFORMATION FOR YOUR RECORDS Model Purchased Date Serial Number
Inhaltszusammenfassung zur Seite Nr. 7
Introduction Runco presents the high performance Crystal Series™ LCD displays, perfect for those who demand our award-winning flat panel performance in more intimate sizes than we offer with our larger plasma monitors. The new Crystal Series™ high definition capable LCD displays offer common features and performance in popular 26, 32 and 40-inch sizes, suitable for close-in viewing where picture quality remains a high priority, but larger displays cannot be accommodated. The Crystal Series
Inhaltszusammenfassung zur Seite Nr. 8
Precautions This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION To turn off main power, be sure to remove the plugs from power outlets. The power outlet socket sho
Inhaltszusammenfassung zur Seite Nr. 9
Control Panels CR-32HD and CR-40HD Front View 8 8 Bottom Side TV/AV MENU - VOL + CH 1 2 3 4 5 6 7 1 TV/AV Button (Input Source Selection) Power Indicator Status 2 MENU Selection Button Indicator Status 3 Volume Adjustment Buttons Red Stand-by 4 Channel Selection Buttons Green Power on Green blinking Remote control 5 Remote Control Sensor 6 Power Button 7 Power Indicator 8 Speakers 9
Inhaltszusammenfassung zur Seite Nr. 10
Control Panels CR-32HD Rear View and Input Panel Right Side Input 2 S-VIDEO 1 L Audio 2 R VIDEO 3 4 Bottom Side 1 1 12 13 INPUT 4 INPUT3 MONITOR-OUT 16 18 20 21 22 5 6 7 10 14 15 17 19 8 9 INPUT1 1 INPUT2 S-Video Input 12 INPUT4 Video Input (VIDEO) 2 INPUT2 Audio Input 13 INPUT4 Audio Input (DTV/DVD) 3 INPUT2 Video Input 14 INPUT1 Video Input 4 Headphone Jack 15 INPUT1 Audio Input 5 RGB Input Connector (PC) 16 INPUT1 S-Video Input 6 DVI-D Input Connector (PC) 17 MONITOR-OUT (Video) 7 Audio Inpu
Inhaltszusammenfassung zur Seite Nr. 11
Control Panels CR-40HD Rear View and Input Panel Right Side Input 2 S-VIDEO 1 L Audio 2 R VIDEO 3 4 Bottom Side 13 14 15 INPUT 4 INPUT3 MONITOR-OU T INPUT1 20 21 5 6 10 1 1 12 16 17 18 19 7 8 9 1 INPUT2 S-Video Input 12 INPUT3 Audio Input (DTV/DVD) 2 INPUT2 Audio Input 13 INPUT4 Video Input (DTV/DVD) 3 INPUT2 Video Input 14 INPUT4 Video Input (VIDEO) 4 Headphone Jack 15 INPUT4 Audio Input (DTV/DVD) 5 Power Switch (Main) 16 INPUT1 Video Input 6 Power Input 17 INPUT1 Audio Input 7 RGB Input Conne
Inhaltszusammenfassung zur Seite Nr. 12
Control Panels Remote Control OFF Button To turn off the unit. OFF ON ON Button Hold down this button for one second to turn on the unit. 1 2 3 NUMERIC Buttons To select channel and to enter pass 4 5 6 codes. The “100” button is to select channels 7 8 9 over 100. TIMER OFF Button TIMER DISCRETE SOURCE SELECTION 0 100 OFF To access sleep timer. • INPUT 1 SOURCE For Composite video or S-Video signals. INPUT INPUT INPUT INPUT • INPUT 2 2 3 4 1 For Composite video or S-Video signals. • INPUT 3 RGB
Inhaltszusammenfassung zur Seite Nr. 13
Connections To view television channels, a signal must be Connecting an Antenna input from either an outdoor antenna or a cable or Cable (Not applicable on television system. the CR-40HD) 1. Connect the antenna or input cable to the 75 Ω coaxial input on the rear of the display. Rear of the TV 2. If you are using an indoor antenna, you may ANT need to turn it when tuning your television until you receive a clear picture. or Cable Television Network Rear of the display (A) For Vid
Inhaltszusammenfassung zur Seite Nr. 14
Connections You can choose the Main or PIP screen to record. Refer to page 24 for more Using the MONITOR OUT information. feature Rear of the display VCR, etc. MONITOR-OUT • Your display has a monitor out feature which can be used by a second VCR, or other auxiliary equipment. To do this, connect your second VCR as follows: 1. Connect a set of audio cables between the AUDIO OUT jacks on the display and the AUDIO IN jacks on the VCR, or auxiliary equipment. 2. Connect a video cable
Inhaltszusammenfassung zur Seite Nr. 15
Connections TIMER To use the display as a PC Monitor 0 100 OFF Connecting to a PC SOURCE 1. Turn the PC on. INPUT INPUT INPUT INPUT 2 3 4 1 2. Depending on the connection, press the DVI or RGB HD button on the remote control. RGB DVI TV HD MEMOR Y 3. Set up the PC Properties. (See page 16) SLEEP DISPLA Y ISF ISF CUST NT DA Y 4. Adjust the screen in PC Mode. (See page 22) RGB Rear of the Display Rear of the PC 1 2 3 4 5 6 7 8 9 10 1 1 12 13 1 4 15 16 17 1 8 19 20 2 1 22 2 3 24 Audio Cabl
Inhaltszusammenfassung zur Seite Nr. 16
Connections 1. First, click on Settings on the Windows Start menu and click on “Control Panel”. Setting the PC Properties 2. Double click on the Display icon. 3. Click on the Settings tab on the display dialog-box. 4. Adjust the resolution to 1024x768 pixels. 5. Click the Advanced button and click the Monitor tab on the dialog-box. Set the vertical-frequency to 60Hz and then click the OK button. Note: – Maximum resolution depends on the Video Card. – Maximum supported resolution is 1
Inhaltszusammenfassung zur Seite Nr. 17
Basic Operations 1. Connect the power cord for your display to the power input on the back of your Connecting the Power display. Cord and Switching the 2. Plug the power cord for the display into a nearby outlet. Display On / Off 3. Press the POWER ( ) button on the remote control or the POWER button on the display panel. 4. To switch your display off, press the POWER ( ) button on the remote control or the POWER button on the display panel. OFF ON 1 2 3 4 5 6 7 8 9 TIME R 100
Inhaltszusammenfassung zur Seite Nr. 18
Basic Operations 1. Press the MENU button on the remote control. Selecting an Aspect 2. Press the ▲▼ buttons to select Aspect Ratio and then press the ENTER or ► Ratio button. 3. Select the appropriate Aspect Ratio by pressing the ▲▼ buttons and then press the ENTER or ► button. • You can select Anamorphic, Standard, Letterbox or VirtualWide. 4. Press the MENU button to return to the previous menu. OR You can also select the Aspect Ratio directly from the remote control using discr
Inhaltszusammenfassung zur Seite Nr. 19
Basic Operations 1. Press the MENU button on the remote control. Selecting Picture Adjust 2. Press the ▲▼ button to select PICTURE ADJUST and then press the ENTER or ► button. 3. Press the ▲▼ button to select Brightness, Contrast, Color, Tint, Sharpness, Color Temp., Backlight, Save Settings or Restore Settings. 4. Press the MENU button to return to the previous menu. Runco CR-32HD Note: Picture Adjust Each input and scan rate has their own Brightness Source picture memories. Make sure yo
Inhaltszusammenfassung zur Seite Nr. 20
Basic Operations 1. Press the MENU button on the remote control. Selecting Audio 2. Press the ▲▼ buttons to select Audio and then press the ENTER or ► button. 3. Press the ▲▼ buttons to select Balance, Equalizer or Surround. 4. Press the MENU button to return to the previous menu. Balance Runco CR-32HD Audio Balance 0 Source Equalizer Aspect Ratio Surround Picture Adjust Audio Audio Channel Balance 1. Adjust the Sound Balance with Equalizer Timer th
