Inhaltszusammenfassung zur Seite Nr. 1
Owner’s Instructions
HP-P5581
This device is a Class B digital apparatus.
Inhaltszusammenfassung zur Seite Nr. 2
Important Warranty Information Regarding Television Format Viewing Wide screen format PDP Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature and the images are constantly moving. Displaying stationary graphics and images on screen, such as the dark side-bars on none
Inhaltszusammenfassung zur Seite Nr. 3
User Instructions Screen Image retention Do not display a still image (such as on a video game) on the plasma display panel for more than several minutes as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, refer to page 52 of this manual to reduce the degree of brightness and contrast of the screen when displaying a still image. Altitude The PDP will not operate normally at altitudes above 6500 ft. Heat on the top of the P
Inhaltszusammenfassung zur Seite Nr. 4
CableCARD and Digital Cable Ready TVs CableCARD and Digital Cable Ready TVs are the products of a new digital cable standard. This new standard is called OpenCable and it is a concerted effort to standardize the digital cable service network interface in North America. For more information, please refer to www.cablelabs.com. Digital Cable Ready TVs are equipped with a proper digital cable tuner to receive digital cable signals from your local cable service provider. They are also designed to w
Inhaltszusammenfassung zur Seite Nr. 5
Q&A 1. Is the antenna I use for existing TV reception good enough for DTV? Over-the-air (OTA) digital TV broadcasting uses the same channels as analog TV and works well with many existing TV antennas. However, DTV broadcast channel assignments are different than analog channels. You should find out whether your local DTV broadcasts are on VHF (channels 2-13) or UHF (channels 14-69) to see if you need a different antenna. If your DTV channels are on UHF and you already get good UHF reception, y
Inhaltszusammenfassung zur Seite Nr. 6
Table of Contents Using the Auto Volume ................................78 General Information Choosing a Digital Sound Format ..................79 Your New Plasma Display Panel ......................8 Setting up the Sub Woofer Output ................80 Remote Control Buttons ................................10 Setting the On/Off Melody ..........................81 Wall Installation Instructions ..........................12 Selecting the Internal Mute............................82 Installing the
Inhaltszusammenfassung zur Seite Nr. 7
PLASMA DISPLA Y P ANEL General Information Your New Plasma Display Panel ......................................................8 Remote Control Buttons ................................................................10 Wall Installation Instructions ..........................................................12 Installing the Speakers ..................................................................16 How to assemble the Stand-Base ....................................................20
Inhaltszusammenfassung zur Seite Nr. 8
Your New Plasma Display Panel Front Panel Œ ´ ˇ ¨ ˆ Ø ∏ ” TOUCH buttons. Press to operate the TV. ’ Œ SOURCE button ˆ ENTER( ) button Press to display all of the available video sources Press to confirm a selection. (TV, AV1, AV2, S-VIDEO1, S-VIDEO2, Ø Power Indicator COMPONENT, DVI, and HDMI). - Power Off : Red ´ MENU button - Power On : Off Displays the main on-screen menu. - Timer On : Green ˇ VOL(+,-) button ∏ Press to increase or decrease the volume. Press to turn the PDP on and off. Also
Inhaltszusammenfassung zur Seite Nr. 9
Side of the TV Ferrite Cores The ferrite cores are used to S-Video Input attenuate undesired signals. When connecting cables, attach one of these ferrite cores to the cable near Video Input the connector. When you connect Side AV cable, Digital Audio out(Coaxial), sub Audio Input (L, R) woofer cable, and Speaker cables, first bind the ferrite core around each cables to secure it. Rear Panel ŒPOWER IN ’S-VIDEO Connect the supplied power cord. Video inputs for external devices with an S-Video ou
Inhaltszusammenfassung zur Seite Nr. 10
Remote Control Buttons Remote Control ŒPOWER button Turns the PDP on and off. ´ANTENNA button Press to select “AIR” or “CABLE”. ˇNumber buttons ANTENNA ¨- button Press to select additional channels (digital and analog) being broadcast by the same station. For example, to select channel “54-3”, press “54”, then press “-” and “3”. ˆMUTE button Press to mute the PDP sound. ØVOL (Volume) buttons Use it to adjust volume. ∏GUIDE button Press to display he on-screen Electronic Program Guide (EPG). ”MEN
Inhaltszusammenfassung zur Seite Nr. 11
¸MTS button Press to choose stereo, mono or Separate Audio Program (SAP broadcast). ˛PIP button Activates picture in picture. ◊ASPECT button Press to change the screen size. ±STILL button Press to pause the current screen. ≠DNIe button Activates DNIe (Digital Natural Image engine). –SRS button Selects TruSurround XT mode. FAV. CH CH. LIST PIP —SET button Used during set up of this Samsung remote control, so that it will work compatibly with other devices ASPECT STILL SLEEP (VCR, Cable Box and
Inhaltszusammenfassung zur Seite Nr. 12
Wall Installation Instructions Installation Notes Do not install the PDP on any location other than a vertical wall. 1 To protect the performance of the PDP and prevent problems, avoid the following locations: 2 • Do not install next to smoke and fire detectors. • Do not install in an area subjected to vibration or high voltage. • Do not install near or around any heating apparatus. Use only recommended parts and components. 3 Parts (Wall attachment panel is sold separately. Check with your d
Inhaltszusammenfassung zur Seite Nr. 13
How to assemble the Wall Mount Bracket The wall mount comes packaged in 3 parts. These parts must be assembled together. Please tighten the captive screws(4EA) in the direction of the arrow after assembling 1 the bracket. Install the Wall Mount Bracket after the screws are securely inserted into the wall. Captive Screws ASSY-HINGE (LEFT) Wall Mount Bracket Separate ASSY-HINGE into left and right. ASSY-HINGE (RIGHT) After installing the wall mount bracket, After securing the screws, be sure t
Inhaltszusammenfassung zur Seite Nr. 14
Wall Installation Instructions Fixing the PDP panel to the wall attachment panel bracket Remove the screws from the back of the PDP. 1 Connect insulation holders to screws (see the illustration below). 2 • If you are uncertain about installation, hire a specialist to install the wall mount bracket. • Be sure to check that the insulation holders are completely secured on both the left and right side after hanging the PDP on the wall mount bracket. • Be careful to avoid getting your fingers caug
Inhaltszusammenfassung zur Seite Nr. 15
How to Adjust Mounting Angle Note Note : Please secure the mounting bracket on the wall surface after setting its angle at 0°. Factory default How to Adjust Mounting Angle Please tighten the captive screw in the direction Hold onto the middle of the PDP to adjust of the arrow after assembling the bracket. the angle (not the sides of the PDP). Change Angle Secure the set to the wall mount bracket. (Please refer to the following instructions.) 1 Set the angle by pulling the upper end of the set a
Inhaltszusammenfassung zur Seite Nr. 16
Installing the Speakers This speaker installation guide is for the PSN5542(BN96-01328A) speakers. Parts Speakers Middle Cabinet Speaker Dust Cover (Wall Mount Only) 1EA 1EA 2EA Speaker Cable Screws 1EA Screw 2EA! Screw 6EA@ How to Assemble the Speakers (When using the Stand) Remove the screws indicated on the rear of the PDP (6 screws on the left and right sides). 1 16
Inhaltszusammenfassung zur Seite Nr. 17
Set the speaker guide bracket into the square grooves located on either side of the PDP’s bottom rear, then push the speaker guide bracket towards the center (as the 2 arrow illustrates). Secure the speaker guide bracket with provided screws @. (Always use the proper screws, as indicated.) Screw② Secure the speaker dust cover by setting it into the grooves located on the front side of the speakers. 3 Connect the speakers to the PDP using the speaker cable. The connection terminals are on th
Inhaltszusammenfassung zur Seite Nr. 18
Installing the Speakers How to Assemble the Speakers (Wall Mount) Remove the screws indicated on the rear of the PDP (6 screws on the left and right sides, 2 screws on the center). 1 Set the speaker guide bracket into the square grooves located on either side of the PDP’s bottom rear, then push the speaker guide bracket towards the center (as the 2 arrow illustrates). Secure the speaker guide bracket with provided screws @. Secure the middle cabinet to the center of the PDP with a screw !. (
Inhaltszusammenfassung zur Seite Nr. 19
Secure the speaker dust cover by setting it into the grooves located on the front side of the speakers. 3 Connect the speakers to the PDP using the speaker cables. The connection terminals are on the rear side of both the PDP and the speakers. 4 (Match the color coded terminals and cables.) BLACK RED BLACK RED Notes • When moving the PDP with the speakers attached, be sure to hold on to the PDP to prevent damage. (Damage may occur to the speaker connecting brackets or the speakers.) • Spea
Inhaltszusammenfassung zur Seite Nr. 20
How to assemble the Stand-Base Firmly secure the pegs to the both sides of the stand base using 8 screws provided. 1 Using the 4 screws for securing the stand pegs and the monitor, firmly attach the monitor to the stand pegs. (The exterior of the set may be different than the picture.) 2 Warning Firmly secure the stand for the PDP before moving it, as the stand may fall and could cause serious injury. ➤ Two or more people should carry the PDP. Never lay the PDP on the floor because of possibl
