Inhaltszusammenfassung zur Seite Nr. 1
MODEL G0738
HANGING 3-SPEED
AIR FILTER
OWNER'S MANUAL
(For models manufactured since 1/12)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Inhaltszusammenfassung zur Seite Nr. 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents INTRODUCTION ............................................... 2 SECTION 5: ACCESSORIES ......................... 17 SECTION 6: MAINTENANCE ......................... 18 SECTION 7: SERVICE ................................... 19 SECTION 1: SAFETY ....................................... 5 SECTION 2: POWER SUPPLY ........................ 8 SECTION 8: WIRING ...................................... 21
Inhaltszusammenfassung zur Seite Nr. 4
INTRODUCTION Manual Accuracy Contact Info your machine may not exactly match the manual www.grizzly.com
Inhaltszusammenfassung zur Seite Nr. 5
Identification To reduce the risk of serious injury, read and understand this entire document before using the machine!
Inhaltszusammenfassung zur Seite Nr. 6
Machine Data Sheet Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
Product Dimensions: Weight................................................................................................................................................................ 31 lbs. Width (side-to-side) x Depth (front-to-back) x Height................................................................ 20 in. x
Inhaltszusammenfassung zur Seite Nr. 7
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indica
Inhaltszusammenfassung zur Seite Nr. 8
DISCONNECTING POWER SUPPLY. GUARDS & COVERS. NEVER STAND ON MACHINE. APPROVED OPERATION. STABLE MACHINE. DANGEROUS ENVIRONMENTS. AWKWARD POSITIONS. ONLY USE AS INTENDED. UNATTENDED OPERATION. OFF USE RECOMMENDED ACCESSORIES. MAINTAIN WITH CARE.
Inhaltszusammenfassung zur Seite Nr. 9
Additional Safety for Air Filters INTENDED USE. DISCONNECTING POWER SUPPLY. OFF REGULAR CLEANING. HAZARDOUS DUST. LEAD PAINT DUST AND ASBESTOS FIBERS. SUSPENDED DUST PARTICLES AND IGNITION SOURCES. DUST ALLERGIES. FIRE SUPPRESSION. IMPELLER H
Inhaltszusammenfassung zur Seite Nr. 10
SECTION 2: POWER SUPPLY Availability Serious injury could occur if you connect the machine to power before completing the setup process. DO NOT connect to power until instructed later in this manual. Circuit Requirements Nominal Voltage ........................................120V Cycle ..........................................................60 Hz Electrocution, fire, or Phase ........................................... Single-Phase equipment d
Inhaltszusammenfassung zur Seite Nr. 11
Grounding & Plug Requirements GROUNDED 5-15 RECEPTACLE Extension Cords 5-15 PLUG Figure 1. Minimum Gauge Size ...........................16 AWG Maximum Length (Shorter is Bette
Inhaltszusammenfassung zur Seite Nr. 12
SECTION 3: SETUP Inventory To reduce the risk of serious injury, read and understand this entire document before using the machine! Needed for Setup Shipping Inventory: (Figure 2) Qty A. B. Description Qty C. D. E. Installed & Not Shown Qty Unpacking please call us immediately at (570) 546-9663 for advice.
Inhaltszusammenfassung zur Seite Nr. 13
Power Connection Test Run Connecting Power Troubleshooting Page 19 To test run the machine: 1. 2. 3. 4. Figure 3. Connecting power. Figure 5 ON Disconnecting Power Figure 4. Disconnecting power. Figure 5.
Inhaltszusammenfassung zur Seite Nr. 14
5. Site Planning 6. OFF 7. ON 8. 9. Figure 6 OFF 10. OFF Figure 6.
Inhaltszusammenfassung zur Seite Nr. 15
Figure 7 It is very important that the hanging air filter be supported properly. Figure 7. Below is a list of things to keep in mind when selecting a spot for the air filter:
Inhaltszusammenfassung zur Seite Nr. 16
To mount the air filter to the ceiling: Mounting to Ceiling 1. Figure 8 Figure 9 Figure 8. Important: The ceiling hooks must only be screwed into solid wood. Otherwise, they may pull out under load and cause the air filter to fall. ONLY mount the air filter unit to joists or table that can hold at least 100 lbs. DO NOT mount the unit only to sheet rock, pressboard, paneling, or honeyc
Inhaltszusammenfassung zur Seite Nr. 17
Note: Some positions for the ceiling hooks may be slightly uneven from each another. To make up for this, minor adjustments can be made to the length of the hanging assem- bly by adjusting the amount that the machine hook is threaded into the air filter housing (see Figure 10). If you do this, tighten the hex nut to secure the hook. Figure 11. Figure 10. 3. 2. 4. Figure 11 Important: If the joists are covere
Inhaltszusammenfassung zur Seite Nr. 18
SECTION 4: OPERATIONS General Filtering Performance Turning ON & OFF ON Note: The remote control communicates with the air filter using infrared (IR) and must be pointed directly at the air filter control panel to work prop- erly. Changing Air Flow Speeds To calculate the recirculating rate for your shop space:
Inhaltszusammenfassung zur Seite Nr. 19
SECTION 5: ACCESSORIES G9955—Bench Top Dual-Fan Dust Filter Some aftermarket accessories can be installed on this machine that could cause it to function improperly, increasing the risk of serious personal injury. To minimize this risk, only install accessories recommended for this machine by Grizzly. NOTICE Refer to the newest copy of the Grizzly Catalog for other accessories available for this machine. T10503—Inner Filter for Model G0738 T10504—Outer Filter for Model G0738 Figure
Inhaltszusammenfassung zur Seite Nr. 20
SECTION 6: MAINTENANCE Cleaning Filters Figure 15. Keep the air filter unit unplugged during all DO NOT use compressed air to blow out the maintenance procedures. INNER filter in the following steps. This can Ignoring this warning may cause damage to the filter. result in laceration or amputation injuries from 3. accidental startup! Optional: Wash the inner filter with water to remo
