Inhaltszusammenfassung zur Seite Nr. 1
the
®
Great Outdoors
Assembly and
Owner’s Manual
A053041
X-Series
Portable
Gas Grill
L.P. Gas
Cylinder
Not Included
ASSEMBLER / INSTALLER:
Leave these instructions with the consumer.
CONSUMER / USER:
Read all of these instructions and keep them in a safe place for future reference.
FOR YOUR SAFETY FOR YOUR SAFETY
If you smell gas: 1 Do not store or use gasoline or other
flammable vapors and liquids in the
1 Shut off gas to the appliance.
vicinity of this or any other appliance.
2 Extinguish any
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents Page Number Chapter 1 - INSTALLATION 4 Necessary Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Choosing a Safe Location . . . . . . . . . . . . . . . . . . . . . . . . . 4 Portable L.P. Gas Grills . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 L.P. Gas Dealer Instructions . . . . . . . . . . . . . . . . . . . . . . . 8 Chapter 2 -ASSEMBLY INSTRUCTIONS 9 Step 1 ( Identifying Parts ) . . . . . . . . . . . . . . . . . . . . . . . . . 10 Step 2 (Att
Inhaltszusammenfassung zur Seite Nr. 3
X-Frame Model Series Gas Grill Installation Chapter 1 Necessary Information to · Operating this or any gas-fired appliance in an enclosed area can produce a build-up Safely Use a Gas Grill of carbon-monoxide, which could result in injury or death. 2. Installation must conform with local The gas fuel used by this product is codes or, in the absence of local codes, with highly flammable and must be used in either the National Fuel Gas Code, ANSI a responsible and cautious manner. Z223.1, NFPA 54 (
Inhaltszusammenfassung zur Seite Nr. 4
9. Make sure that the drip pan is in place under the grill bottom. · Hot drippings from cooking food could damage the fuel supply system. IMPORTANT: NEVER leave a grill unattended when in use. Portable L.P. Gas Barbecue Grills WARNING: Do not use natural gas in an appliance designed for L.P. gas. Use only liquid propane (L.P.) gas in an appliance designed for L.P. gas. L.P. Gas Liquid Propane (abbreviated L.P.) gas is stored under high pressure inside a cylinder and will vaporize when released.
Inhaltszusammenfassung zur Seite Nr. 5
4. The pressure regulator and hose assembly provided is factory set at an outlet Dual Burner pressure of 11 inches water column (.4 lb. Fuel-Control Valve per sq. Inch). WARNING: Any attempt to adjust the Type 1 Fuel Valve regulator is dangerous and could create a Regulator Orifice situation causing personal injury or property damage. Consult your L.P. gas dealer if you think the regulator is not working properly. L.P. GAS SUPPLY CYLINDER Fuel Supply Hose L.P. Cylinders can be obtained at the st
Inhaltszusammenfassung zur Seite Nr. 6
The L.P. gas cylinder must have a shut-off Have the gas dealer weigh the cylinder valve terminating in a Type 1 L.P. gas- after filling to ensure that the cylinder is not cylinder-valve outlet. AType 1 compatible overfilled. cylinder with a Type 1 cylinder valve has a positive seating connection that does not DANGER: permit gas flow until a positive seal has been a.) Do not store a spare L.P. gas cylinder obtained. under or near this appliance. b.) Never fill the gas cylinder beyond 80 The cylin
Inhaltszusammenfassung zur Seite Nr. 7
Take These Instructions to the L.P. Gas Dealer When using a cylinder exchange, be sure the The L.P. gas cylinder has a Type 1 cylinder exchanged cylinder is a Type 1 cylinder; a 510 valve with a back-check module in its outlet POL cylinder will not fit a Type 1 regulator. that will not permit gas to flow until an evacuation device is installed. To purge the L.P. gas cylinder, the back-check module must FILLING AND PURGING be opened with an evacuation device. TYPE 1 L.P. GAS CYLINDERS PURGING AND
Inhaltszusammenfassung zur Seite Nr. 8
X-Frame Model Series Gas Grill Assembly Instructions Chapter 2 Getting Started 1. Please follow the steps in the order that they are presented. 2. Assemble the grill where you plan to use it. 3. You may want to place an old towel or cloth at the assembly site to prevent nuts and bolts from becoming lost. 4. Have a friend help. An assistant can make the assembly easier by holding the parts in place while you fasten the nuts and bolts. 5. To be ready to barbecue immediately, have the L.P. gas cyli
Inhaltszusammenfassung zur Seite Nr. 9
Assembly Step 1 - Identifying the Grill Parts Locate these parts: Heat Warming Rack Indicator Note: Refer to the parts listing on page 33 of the Grill Head manualforreplacementpart Cooking Grid information. Assembly Handle Heat Shield Lid Handle Heat Plate Left Side Rear Right Side Table Table X-Frame Table Bracket Table Bracket Table Arms Front X-Frame with Control Panel Tank Heat Shield Table Arms Drip Cup and Holder Legs Legs Wire X-Brace Wire Tank Modesty Retainer Panel Left Foot Wheel (Tank
Inhaltszusammenfassung zur Seite Nr. 10
Assembly Step 2 - Attach Legs to X-Frames Tools Needed: LOCATE THESE PARTS: X-Frame X-Frame Phillips head screwdriver with Control USE HARDWARE ”A” Panel 2 Left M6x15mm M6 Flat A B Legs Bolt (8) Washer (8) 2 Right Legs 1. Attach the leg to the X-frame by inserting the top tabs into the corresponding slots in the X-frame as shown. 2. Line up the bolt holes on the side of each leg and insert a bolt into each of the bolt holes. 3. Tighten the bolts securely. 4. Repeat steps 1 through 3 above for ea
Inhaltszusammenfassung zur Seite Nr. 11
Assembly Step 3 - Attach the Feet Tools Needed: LOCATE THESE PARTS: Left Foot Wheel (tank side) A Phillips head screwdriver Wheel B Washer Axle Nut 17mm Wrench Axle USE HARDWARE ”B” Hub Right Foot Cap A B C D Wheel M10 Axle M6x15mm M6 Flat Washer (8) Washer(2) Nut (2) Bolt (8) 1. Assemble the wheels and axle to the tank-side foot as shown above right. Insert the axle through the foot, one wheel on each end, tighten one nut and wheel washer on each end, and snap the hub caps onto the wheels 2. At
Inhaltszusammenfassung zur Seite Nr. 12
Assembly Step 4 - Install the Tank Retainer Tools Needed: USE HARDWARE ”C” Phillips head screwdriver LOCATE THESE PARTS: B M4 Wing M4x10mm M6 Wing A B C Nut (1) Bolt (1) Nut (6) 1. Insert the legs of the wire tank retainer Wire A into the mounting brackets inside the grill X-Brace legs. The wire tank retainer must be mounted on the wheel side of the grill. Wire Tank Retainer 2. Align the center hole of the x-brace wires, insert the M4 bolt through both wires, and thread on the M4 wing nut as sho
Inhaltszusammenfassung zur Seite Nr. 13
Assembly Step 5 - Attach the Modesty Panel Tools Needed: LOCATE THESE PARTS: Phillips head screwdriver Tank 7mm Wrench Heat Shield USE HARDWARE ”D” B M4 KEPS M4x15mm A Nut (6) Bolt (6) Modesty Panel 1. Position the modesty panel between the front legs of the assembly. Align the mounting tabs with the bolt holes in A the legs. B From the back side of the assembly, insert the 2. M4 bolts through each of the mounting holes and thread on the M4 KEPS nuts. DO NOT yet insert the bolt indicated - it wi
Inhaltszusammenfassung zur Seite Nr. 14
Assembly Step 6 - Attach the Side Tables Tools Needed: LOCATE THESE PARTS: Table Mounting Left Side Table Brackets (2) Phillips head screwdriver 10mm Wrench USE HARDWARE ”E” A B C D M6x25mm M6 Hex Lock Washer Right Side Table Side Table Arms (2 Left, 2 Right) Bolt (8) Nut (8) Washer (8) (8) 1. To assemble each table, use one left and one right table arm. 2. Line up the bolt hole of the table arms to the INSIDE set of holes on the side table as shown. 3. For each bolt location, insert a M6 bolt.
Inhaltszusammenfassung zur Seite Nr. 15
Assembly Step 7 - Installing the Grill Head Tools Needed: LOCATE THESE PARTS: Grill Head Phillips head screwdriver Assembly USE HARDWARE ”F” M6x15mm M6 Flat Bolt A B C Bolt (4) Washer (4) Gasket (4) 1. Holding the grill head upright, slightly rotate the knob side down and set it onto the frame assembly. The knobs will insert through the control panel first, then rotate the grill head down until it rests properly onto the frame. 2. Line up the 4 bolt holes near the inside corners of the grill tub
Inhaltszusammenfassung zur Seite Nr. 16
Assembly Step 8 - Ignitor Installation 1. Locate the loose end of the ignitor wire. Connect it to the ignitor electrode underneath the grill tub, between the two burner tubes. 2. Using the remaining bolt and nut from Step 5 (page 14), bolt the hose bracket to the frame. Be sure the bolt mounts through the modesty panel tabs and the frame leg. Securely tighten the bolt and nut using a phillips head screwdriver and 7mm wrench. Installing the Battery 1. Unscrew the cap from the ignitor button. 2. I
Inhaltszusammenfassung zur Seite Nr. 17
Assembly Step 9 - Installing the Lid Handle USE HARDWARE ”G” LOCATE THESE PARTS: Handle Heat Shield M6 Wing M6 Flat Bolt A B C Nut (2) Washer (2) Gasket (2) No tools are required for this step. Lid Handle 1. Align the lid handle bolts with the mounting holes in the lid and set the handle on the grill lid. 2. From the inside of the lid, thread on a gasket onto each bolt. 3. Place the Heat Shield C onto the bolts. 4. Thread on a washer B and wing nut for each A handle bolt. 5. Securely tighten the
Inhaltszusammenfassung zur Seite Nr. 18
Assembly Step 10 - Installing the Grids LOCATE THESE PARTS: Cooking Grid Heat Plate No tools are required for this step. 2 1 2 1. Set the Heat Plate into the tub as shown. It will rest on the lowest ledge inside the tub, just above the burner. 2. Set the cooking grid into the tub. It will rest on the topmost ledge of the tub. 19
Inhaltszusammenfassung zur Seite Nr. 19
Assembly Step 11 - Install the Warming Rack No tools are required for this step. LOCATE THESE PARTS: 1. Position the warming rack as shown and insert one end of the rack into the lid as shown. 2. Working on the same side of the grill, Warming Rack Assembly insert one foot of the warming rack into the mounting hole near the top of the grill tub. 3. Work the other end of the rack into the other side of the lid. Insert the other foot of the warming 4. rack into the other side of the grill tub. It w
Inhaltszusammenfassung zur Seite Nr. 20
Assembly Step 12 - Install the Drip Cup No tools are required for this step. LOCATE THESE PARTS: 1. Underneath the grill tub, insert the drip Drip Cup cup holder into the mounting holes on either side of the grease drain hole. 2. Set the drip cup into the drip cup holder. Drip Cup Holder Grease Drain Hole LOCATE THESE PARTS: Heat 10mm wrench required for this step. Indicator Nut Heat Indicator Gasket Heat Indicator 1. Insert the stem of the heat indicator into the front of the lid, through the n
