Inhaltszusammenfassung zur Seite Nr. 1
Liquid Propane Conversion Kit
For the following Coleman® Gas Barbecue Grills:
8350 Series (M/N 9992-648)
WARNING
Note: These instructions apply to
� If the information in this document is not followed exactly, a fire or
grill Model 8350 Series. The parts
explosion may result causing property damage, personal injury or loss
of life. Read the Coleman® Gas Barbecue Use, Care & Assembly
included are designed for your
Manual With Grill Lighting Instructions, before attempting installation
specific gr
Inhaltszusammenfassung zur Seite Nr. 2
Liquid Propane Gas Conversion Instructions 1 4 2 3 6 5 Item No. Qty Description 1 9992-4421 1 Main Burner Valve & Manifold Assembly (L.P.) 8350 2 47310103 1 Main Regulator Hose Assembly (L.P.) 3 08006001 1 Rear IR L.P. Orifice (8350) 4 08138381 1 Connector 3/8" FNPT x 3/8" MFLR 5 49900004 1 Pipe Sealant 6 9992-462 1 LP Conversion Sticker 2
Inhaltszusammenfassung zur Seite Nr. 3
Liquid Propane Gas Conversion Instructions Tools Needed: Fig 1 Phillips head screwdriver 1/4" nut driver * 9/16" wrench Adjustable wrench Heat Tents * socket set with extension can also be used. Rear Heat Shield Be sure gas supply is off, the knobs are in the off Fig 2 position and the grill is cool. 1. Remove cooking grates and heat tents. Screws (See Fig. 1). 2. Remove the screws holding the rear heat shield in place. Lift out rear heat shield and set aside (Fig. 2). Fig 3 3. Remove the two s
Inhaltszusammenfassung zur Seite Nr. 4
Liquid Propane Gas Conversion Instructions 5. Remove the screws from the bottom of the heat shield, holding the front heat shield in place. The screws are located under the bottom lip of the shield (Fig. 5). Fig 5 6. Remove the side heat shield screws located under the bottom lip of the heat shield. Remove all of Screws the top heat shield screws (Fig. 6). under lip 7. Remove the front heat shield (Fig. 7). 8. Grasp and push the burners towards the rear of the grill to detach the burner from the
Inhaltszusammenfassung zur Seite Nr. 5
Liquid Propane Gas Conversion Instructions 10. Disconnect the right side flexline from the Flex Line manifold using the adjustable wrench. This will free up the right side of the manifold (Fig. 9). Fig 9 11. Disconnect the left side flexline from the back infrared valve using an adjustable wrench. This will free up the left side of the manifold (Fig. 10). Gas Inlet Flex Line 12. Remove the control knobs from the front of the grill (Fig. 11). Manifold 13. Remove the two screws holding each bezel
Inhaltszusammenfassung zur Seite Nr. 6
Liquid Propane Gas Conversion Instructions You are now ready to install the new LP manifold. Control Knob Stems 16. NOTE: New screws for the bezels are inserted Fig 15 into the new LP manifold at the factory. Remove them before proceeding with Step 17. 17. Place the new manifold into the grill body with the control knob stems going outward through control panel front (Fig. 15). Valves 18. Reattach the bezels to the manifold with the Burners screws. Make sure that "off" is facing up on the Fig 1
Inhaltszusammenfassung zur Seite Nr. 7
Liquid Propane Gas Conversion Instructions Installing the L.P. regulator 28. Remove the NG regulator from the main gas pipe using an adjustable wrench. The NG Fig 17 regulator is located on bottom of grill head (Fig. 17). Note: For the following steps, the supplied pipe dope needs to be applied to all fittings before the fittings are attached. 29. Attach the 3/8" FNPT connector brass fitting to the main gas pipe (Fig. 18). Pipe dope should not be used on any Fig 18 flared fittings! 30. Attach t
Inhaltszusammenfassung zur Seite Nr. 8
Liquid Propane Gas Conversion Instructions Converting the Rear Infrared Burner to LP 31.Remove the four screws on the inside of the grill that hold the rear infrared cover in place (Fig. 20). Fig 20 Rear 32. Close the grill hood slowly. Screws 33. Remove the two screws from the back infrared cover, located on the back of the grill (Fig. 21). 34.Grasp rear infrared cover and remove it from the grill. Fig 21 35.Disconnect flex line and twist orifice elbow to remove NG orifice (Fig. 22 & 23). 36.Co
Inhaltszusammenfassung zur Seite Nr. 9
Liquid Propane Gas Conversion Instructions Label the Grill 44. Apply conversion label 9992-462 on the grill, next to the lighting instruction label (Fig. 25). Fig 25 Note: At the completion of the conversion, a leak test should be performed on all fittings. See Use and Care manual for leak testing procedure. Label Your Grill Installation is now complete. Enjoy your grill safely. Connections must comply with local requirements and are the sole responsibility of the person performing the work
Inhaltszusammenfassung zur Seite Nr. 10
Liquid Propane Gas Conversion Instructions NOTES __________________________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________ _____________________
Inhaltszusammenfassung zur Seite Nr. 11
Liquid Propane Gas Conversion Instructions NOTES __________________________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________ _____________________
Inhaltszusammenfassung zur Seite Nr. 12
The Coleman Company, Inc. • 3600 North Hydraulic Wichita, KS 67219 U.S.A. 1-800-356-3612 � TDD: 316-832-8707 www.coleman.com ©2006 The Coleman Company, Inc. All rights reserved. Coleman® and are registered trademarks of The Coleman Company, Inc. 9992-449 (8/14/06)
