Inhaltszusammenfassung zur Seite Nr. 1
ASSEMBLY AND OPERATING INSTRUCTIONS
MIRAGE 485
OUTDOOR STAINLESS STEEL GAS GRILL
DANGER
NOTICE TO INSTALLER:
IF YOU SMELL GAS:
• Shut off gas to the appliance.
LEAVE THESE INSTRUCTIONS
Extinguish any open flame.
WITH THE GRILL OWNER FOR
Open lid.
FUTURE REFERENCE
If odor continues, keep away from the
appliance and immediately call your
gas supplier or your fire department
DO NOT TRY TO LIGHT THIS APPLIANCE WITHOUT READING LIGHTING INSTRUCTIONS
SECTION OF THIS MANUAL
NAPOLEON APPLIAN
Inhaltszusammenfassung zur Seite Nr. 2
THANK YOU FOR CHOOSING NAPOLEON NAPOLEON products are designed with superior components and materials, and are assembled by trained craftsmen who take great pride in their work. The burner and valve assembly are leak tested and test-fired at a quality test station. This grill has been thoroughly inspected by a qualified technician before packaging and shipping to ensure that you, the customer, receive the quality product you expect from NAPOLEON. We at Napoleon are dedicated to you, “our valu
Inhaltszusammenfassung zur Seite Nr. 3
SAFETY PRECAUTIONS WARNING WARNING Do not store or use gasoline or other flam- Failure to follow these instructions could mable liquids or vapor in the vicinity of this result in property damage, personal or any other appliance. An L.P. cylinder not injury or death. Read and follow all connected for use must not be stored in the warnings and instructions in this manual vicinity of this or any other appliance. Keep prior to operating grill. area clear and free from combustible WARNING SAFE OPE
Inhaltszusammenfassung zur Seite Nr. 4
CAUTION CYLINDER SPECIFICATIONS/GAS HOOK UP This gas barbecue is certified under Canadian and American national standards, CAN/CSA-1.6-2005 and ANSI Z21.58 -2005 respectively for outdoor gas grills and should be installed to conform with local codes. In absence of local codes, install to the current CAN/CGA-B149.1 Propane Installation Code in Canada or to the National Fuel Gas Code, NFPA54/ANSI Z223.1 in the United States. If a rotisserie motor is used, it must be electrically grounded in accor
Inhaltszusammenfassung zur Seite Nr. 5
LIGHTING INSTRUCTIONS OPEN LID. ENSURING BURNER CONTROLS ARE IN THE OFF POSITION, TURN ON THE GAS SUPPLY VALVE. SIDE BURNER RIGHT BURNER CENTER BURNER LEFT BURNER MAIN BURNER LIGHTING SIDE BURNER LIGHTING 1. OPEN SIDE BURNER 1. PUSH AND TURN ANY MAIN COVER. BURNER KNOB SLOWLY TO THE ’HI’ POSTION. THIS ACTION WILL IGNITE THE PILOT FLAME WHICH WILL IN TURN LIGHT THE 2. PUSH AND TURN THE SELECTED BURNER. IF THE SIDE BURNER CONTROL PILOT LIGHTS, CONTINUE TO KNOB SLOWLY TO THE PUSH DOWN ON THE
Inhaltszusammenfassung zur Seite Nr. 6
OPERATING THE GRILL BURN IN PROCEDURE When lit for the first time, the gas grill will emit a slight odour. This is a normal temporary condition caused by the "burn-in" of internal paints and lubricants used in the manufacturing process and will not occur again. Simply run the main burners on high for approximately ½ hour with the lid closed. MAIN BURNER USE: When searing foods, preheating is recommended by operating all main burners in the high position with the lid closed for approximately 15 m
Inhaltszusammenfassung zur Seite Nr. 7
MAINTENANCE/CLEANING INSTRUCTIONS It is recommended that this gas grill be thoroughly inspected and serviced annually by a qualified service person. • Do not use pressure washer to clean any part of the unit. Ensure that the burners are turned off prior to cleaning. Avoid unprotected contact with hot surfaces. Clean grill in an area where cleaning solutions will not harm decks, lawns or patios. Do not use oven cleaner to clean any part of this gas grill. Do not use a self cleaning oven to cl
Inhaltszusammenfassung zur Seite Nr. 8
MAINTENANCE/CLEANING INSTRUCTIONS HOSE - Check for abrasion, melting, cuts and cracks. If any of these conditions exist, do not use gas grill. Have part replaced by your Napoleon Gas Grill dealer, or qualified gas installer. CLEANING THE OUTSIDE OF THE GAS GRILL - Do not use abrasive cleaners to clean any painted, porcelain or stainless steel parts. Porcelain enamel components must be handled with additional care. The baked on enamel finish is glass like, and will chip if struck. Touch-up e
Inhaltszusammenfassung zur Seite Nr. 9
TROUBLESHOOTING Problem Possible Causes Solution Low heat / Low flame when For propane - improper lighting Ensure lighting procedure is followed carefully. All gas grill valve turned to high. procedure. valves must be in the off position when the tank valve is turned on. Turn tank on slowly to allow pressure to equalize. See lighting instructions. For natural gas - undersized Pipe must be sized according to installation code. supply line. For both gases - improper Pre-heat grill with both mai
Inhaltszusammenfassung zur Seite Nr. 10
ORDERING REPLACEMENT PARTS WARRANTY INFORMATION KEEP YOUR RECEIPT AS MODEL: PROOF OF PURCHASE TO VALIDATE YOUR DATE OF PURCHASE: WARRANTY SERIAL NUMBER: (record information here for easy reference) Before contacting the customer service department, check the NAC web site for more extensive cleaning, maintenance, troubleshooting and part replacement instructions at www.napoleongrills.com. Contact the factory directly for replacement parts and warranty claims. The customer service department is
Inhaltszusammenfassung zur Seite Nr. 11
7/16 3/8 ASSEMBLY INSTRUCTIONS CAUTION: During unpacking and assembly it is recommended that you wear work gloves and safety glasses for your protection. Although we make every effort to make the assembly process as problem free and safe as possible, it is characteristic of fabricated steel parts that the edges and corners may be sharp and can cause cuts if handled incorrectly during assembly. GETTING STARTED 1. Remove all cart panels, hardware, and grill head from carton. Raise lid and remov
Inhaltszusammenfassung zur Seite Nr. 12
3/8 7/16 1 x N430-0002 MAGNET CATCH 1 Magnet Installation Snap magnet into slot in front of bottom shelf. 16 X 16 X N570-0073 (1/4-20 X 3/8”) N450-0027 (1/4-20) 2 Caster/Bracket Installation Attach (4) casters, using (4) 1/4 - 20 X 3/8” screws and (4) 1/4-20 lock nuts for each caster. Attach brackets under front casters as illustrated. Tighten securely. non revolving caster- left side 12
Inhaltszusammenfassung zur Seite Nr. 13
3/8 PROPANE ONLY 3 Propane Tank Ring Installation Insert propane tank ring into slots in bottom shelf as shown. Fold tabs over to secure in place. 4 X N570-0080 (#14 X 1/2") 4 Left and Right Cart Panel Installation Install end cart panels ensuring slots in panel are to the top, rest panel on bottom shelf and line up holes. Fasten using (4) #14 x 1/2” screws. 13
Inhaltszusammenfassung zur Seite Nr. 14
3/8 6 X N570-0080 (#14 X 1/2") 5 Rear Cart Panel Installation Fit rear cart panel between the two end panels, ensure large hole in panel is to the bottom right hand corner as illustrated. Fasten using (6) #14 x 1/2” screws, three on each side. Condiment Basket / Propane Tank Mount Installation 6 Rotate basket slightly to allow wire to enter the holes in the side panel. Push through and upwards, rotating to allow the bend in the wire to pass through the holes. Lay basket flat against the side
Inhaltszusammenfassung zur Seite Nr. 15
3/8 3/8 6 X 1 x N430-0002 MAGNET CATCH N570-0080 (#14 X 1/2") Front Cabinet Support Installation 7 Fasten top rail assembly to the front of side panels using (4) #14 x 1/2” screws. For ease of installation start all screws before tightening completely. Attach magnet bracket to bottom of top rail using (2) #14 x 1/2” screws, and snap mag- net into place as shown. 2 X PROPANE ONLY N570-0080 (#14 X 1/2") 8 Propane Tank Heat Shield Installation Attach propane tank heat shield above propane tank ri
Inhaltszusammenfassung zur Seite Nr. 16
3/8 6 x N570-0073 (1/4-20 x 3/8”) Grill Head Installation 9 PROPANE ONLY - To avoid assembly difficulties, prior to mounting the grill head, remove zip tie holding regulator up under control panel. This was installed at the factory to protect the regulator hose during shipping and is no longer re- quired. (Take care when removing the tie not to damage the hose). Lift grill head and place on assembled cart, lining up holes in top of side cart panels with holes in bottom of base. Faste
Inhaltszusammenfassung zur Seite Nr. 17
3/8 3/8 10 x N570-0073 (1/4-20 x 3/8") Assembling End Caps to Side Shelf / Side Burner 10 Peel protective coating from side shelf / side burner. Attach corresponding end cap as shown using (5) (1/4-20 x 3/8”) screws. Bend tabs on front of shelf up with a flat head screw driver, insert screw through tab and into end cap. 4 X 4 X N735-0001 (1 1/16” insulated washer) N570-0082 (1/4-20 x 5/8") Side Shelf Installation 11 Insert (4) 1/4-20 x 5/8” screws through washers into threaded holes in side o
Inhaltszusammenfassung zur Seite Nr. 18
3/8 1 X 4 X 4 X N160-0016 N735-0001 (1 1/16” insulated washer) N570-0082 (1/4-20 X 5/8") 12 Side Burner Installation Insert (4)1/4-20 x 5/8” screws through washers into threaded holes in side of base. Do not tighten all the way. Slide assembled side burner over screw heads and finish tightening. Attach 1/2” flex connector hose from manifold to fitting on end of side burner hose. Fit orifice into burner tube and secure with hose retainer clip supplied. Attach wire from manifold to side burne
Inhaltszusammenfassung zur Seite Nr. 19
3/8 4 X N735-0003 2 x N105-0011 4 x N570-0073 (1/4” LOCK WASHER) DOOR BUSHING (1/4-20 X 3/8") Cabinet Door Installation 13 Install door handle onto front of door using (2) 1/4-20 x 3/8” screws and (2) 1/4” lock washers per door. Insert pivot rod through hole on inside top of door. Holding door in one hand, direct pivot rod into hole in underside of front cabinet support. Once secure, let rod slide down and through hole in bottom of door and into bushing in bottom shelf. BUSHING 19
Inhaltszusammenfassung zur Seite Nr. 20
3 X N305-0057 14 Sear Plate Installation Insert sear plates into base, position one over each tube burner with slots down to allow drippings to travel through. 1 X N520-0023 2 X N305-0058 15 Grill and Warming Rack Installation Postion grills and warming rack into base as shown. Rest warming rack on brackets inside hood and grills on front and back lip of base. 20
