Inhaltszusammenfassung zur Seite Nr. 1
®
rino 600 series
quick start manual
Inhaltszusammenfassung zur Seite Nr. 2
Keys Getting Started warninG See the Important Safety and Product Information guide in the product box for product warnings and other important information. ➊ When using your device the first time, complete these tasks. ➋ ➌ 1. Install the batteries or battery pack (page 4–5). 2. If necessary, charge the lithium-ion battery (page 4). 3. Acquire satellite signals (page 5). 4. Set up the radio (page 6). Key Description Select to send out a call ➊ tone. If enabled (page 8), the call key
Inhaltszusammenfassung zur Seite Nr. 3
Hold to turn on or off Battery information ➋ the unit. Select to adjust warninG backlight, volume, squelch level, and to lock This product contains a lithium-ion or unlock the screen. battery. To prevent the possibility of personal injury or product damage Hold to talk. PTT stands ➌ for push-to-talk. caused by battery exposure to extreme heat, store the device out of direct Manual Conventions sunlight. All the pages are found on the home The temperature rating for the device screen.
Inhaltszusammenfassung zur Seite Nr. 4
installing the Lithium-ion Charging the Lithium-ion Battery Battery note: The lithium-ion battery pack Before you use the device the first can be used with only the Rino 650 time, charge the battery. and 655t. Charging a fully depleted battery takes 1. Locate the battery pack ➊ that 6 hours. The device will not charge came in the product box. when outside the temperature range from -4°F to 140°F (from -20°C to 60°C). ➊ 1. Plug the AC charger into a standard wall outlet. 2. Lift the weat
Inhaltszusammenfassung zur Seite Nr. 5
4. Charge the device completely. 3. Replace the battery cover, and turn the D-ring clockwise. A fully charged battery can run for up to 14 hours before it must be acquiring Satellite recharged. Signals installing aa Batteries It may take 30 to 60 seconds to acquire Instead of the lithium-ion battery pack, signals. you can use alkaline, NiMH, or lithium 1. Go outdoors to an open area. batteries. This is especially handy when you are on the trail and cannot 2. Turn on the device. charge
Inhaltszusammenfassung zur Seite Nr. 6
2. Use + or - to select a channel. radio The radio page provides the user Scanning Channels interface for Family Radio Service You can scan the channels for voice (FRS) and General Mobile Radio activity. Service (GMRS) radio operations. Select Radio > Scan. Channels Setting Up a Scan List The Rino has a total of 30 channels and You can pick which channels and codes 121 squelch codes. to scan. Selecting specific channels and codes reduces the scan time and helps Channel Frequency prev
Inhaltszusammenfassung zur Seite Nr. 7
navigating to a Contact Contacts Before you can navigate to a contact, The first time a signal is received from you must save the contact (page 7). another Rino user, the new contact page appears. From that page you 1. Select Contacts. can show their location on the map, 2. Select a contact. navigate to their location (page 7), or 3. Select View Map > Go. add them to your contacts list. 4. Follow to your destination. Saving a new Contact When a new contact signal is received, notes the
Inhaltszusammenfassung zur Seite Nr. 8
3. Select . Sending Your Location Before you can send a location, you 4. Select an option: must enable peer-to-peer positioning • Select Send note to send (page 8). without saving. 1. Select Share Wirelessly > • Select Save. t ransmit on Radio. • Select Send and Save. 2. Select a category. about Peer-to-Peer 3. Select an item. Positioning 4. Select Send. note: You can send a location only waypoints once every 30 seconds, due to FCC restrictions. Waypoints are locations you record and st
Inhaltszusammenfassung zur Seite Nr. 9
3. Follow to your destination. navigating to a Destination Compass You can use the Where To? menu to The device has a 3-axis compass. You navigate to a destination. Not all Where can use a bearing pointer or a course To? categories are available in all areas pointer to navigate to your destination. and maps. note: When the device is in an auto 1. Select Where t o?. mount, the compass displays GPS 2. Select a destination. heading, not magnetic heading. 3. Select Go. Calibrating the Co
Inhaltszusammenfassung zur Seite Nr. 10
1. From the compass, select MenU. Camera and Photos 2. Select Calibrate Compass > Start. You can take photos with the Rino 655t. When you take a photo, the 3. Follow the on-screen instructions. geographic location is automatically saved in the photo information. You Tracks can navigate to the location like a A track is a recording of your path. waypoint (page 11). The track log contains information about points along the recorded path, Taking a Photo including time, location, and elevat
Inhaltszusammenfassung zur Seite Nr. 11
3. Select a photo to see a larger view note: This does not erase any of your of it. data or settings. navigating to a Photo Contacting Garmin 1. Select Where t o? > Photos. Product Support 2. Select a photo. You can contact Garmin Product 3. Select Go. Support if you have any questions 4. Navigate using the map (page 9) or about this product. compass (page 9). • In the USA, go to www.garmin.com /support, or contact Garmin USA registering Your Device by phone at (913) 397.8200 or Help us
Inhaltszusammenfassung zur Seite Nr. 12
For the latest free software updates (excluding map data) throughout the life of your Garmin products, visit the Garmin w eb site at www.garmin.com. © 2011 – 2013 Garmin Ltd. or its subsidiaries Garmin International, Inc. st 1200 East 151 Street, Olathe, Kansas 66062, USA Garmin (Europe) Ltd. Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9LR UK Garmin Corporation nd No. 68, Zhangshu 2 Road, Xizhi Dist., New Taipei City, 221, Taiwan (R.O.C.) www.garmin.com January 2013
