Inhaltszusammenfassung zur Seite Nr. 1
®
GPSMAP
2006/2010
& GPS 17
installation instructions
Inhaltszusammenfassung zur Seite Nr. 2
INSTALLATION INSTRUCTIONS © Copyright 2005 Garmin Ltd. or its subsidiaries Garmin International, Inc. Garmin (Europe) Ltd. Garmin Corporation st nd 1200 East 151 Street, Unit 5, The Quadrangle, No. 68, Jangshu 2 Road, Olathe, Kansas 66062, U.S.A. Abbey Park Industrial Estate, Shijr, Taipei County, Taiwan Tel. 913/397.8200 or 800/800.1020 Romsey, SO51 9DL, U.K. Tel. 886/2.2642.9199 Fax 913/397.8282 Tel. 44/0870.8501241 Fax 886/2.2642.9099 Fax 44/0870.8501251 All rights reserved. Except a
Inhaltszusammenfassung zur Seite Nr. 3
INSTALLATION INSTRUCTIONS INTRODUCTION The GPSMAP 2006C/2010C Multi-Function Display (MFD) and GPS 17 must be properly installed according to the following instructions for the best possible performance. To complete the installation, you need the appropriate fasteners, tools, and mounts listed in each section. These items are available at most marine dealers. Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding. When drilling or cutting, always check
Inhaltszusammenfassung zur Seite Nr. 4
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Surface Mount Tools • Drill and Drill Bit • Screwdriver • Pencil • Mounting Hardware (not included) NOTE: Mounting hardware (fasteners) not included. Mounting holes are 5/16" (7.9 mm) in diameter. To install the Bail Mount and unit: 1. Using the bail mount as a template, mark the location of the four mounting holes. Be sure to leave at least two inches of clearance behind the unit for the wiring. 2. Using an appropriate size drill bit, dril
Inhaltszusammenfassung zur Seite Nr. 5
INSTALLATION INSTRUCTIONS Flush Mount Tools • Flush Mount Template • Jig saw • Masking tape • Scissors • Drill • Drill bits—1/8" (3 mm) and 3/8" (6 mm) • 1/16" (2 mm) Allen (Hex) wrench • Sockets or wrenches • Hammer • Center punch Flush Mount To flush mount the GPSMAP 2006C/2010C: 1. Trim the Flush Mount Template and tape it in the location you want. 2. Using the center punch, indent the center of each mounting hole location. 3. Using an 1/8” (3 mm) drill bit, drill the four mounting holes. 4
Inhaltszusammenfassung zur Seite Nr. 6
INSTALLATION INSTRUCTIONS Installing the GPS 17 The GPS 17 can be flush mounted or installed on any standard 1" O.D. (Outer A B O V E - B E S T Dimension), 14 threads-per-inch marine mount. When mounting the GPS 17, the cable can be run externally or through the mounting panel or through the center of Ra da r the marine mount. 3' B E L OW - O K The GPS 17 connects to the 18-pin Power/Data Cable on the GPSMAP VHF Radio Antenna Radar 2006C/2010C and provides the GPS/WAAS signal for the unit. I
Inhaltszusammenfassung zur Seite Nr. 7
INSTALLATION INSTRUCTIONS To attach the enclosed pole mount to the GPS 17: To mount the GPS 17 with cable outside mount: 1. Thread the cable though the pole mount. 1. Place the cable in the vertical slot along the side of the base of the unit. 2. Align the tab on the mount to the notch on the GPS 17. 2. Screw the GPS 17 onto the mount. DO NOT overtighten the 3. Use the enclosed screws to secure the mount to the base. head. It is possible to over tighten the unit and cut the cable. 3. With th
Inhaltszusammenfassung zur Seite Nr. 8
INSTALLATION INSTRUCTIONS Wiring There are two wiring diagrams provided for you convenience. The first is a simple hook-up showing the GPSMAP 2006/2010 (using the 18- pin wiring harness), the GPS 17 and the alarm circuit. The Alarm does not have to be wired for the unit to function. The second is a complete wiring diagram showing the GPSMAP 2006/2010 (using the 18-pin wiring harness) interfacing with a variety of different equipment. The extra 5-pin wiring harness that came with the unit is int
Inhaltszusammenfassung zur Seite Nr. 9
INSTALLATION INSTRUCTIONS + S H I P ' S B A T T E R Y 1 0 - 3 2 V O L T S - G A R M I N G S D 2 0 S O U N D E R M O D U L E ( S E E G S D 2 0 I N S T A L L I N S T R U C T I O N S ) ( - ) ( - ) ( - ) 4 . A G A R M I N S O U N D E R U N I T ( O T H E R T H A N G S D 2 0 ) C A N P R O V I D E W A T E R D E P T H , W A T E R T E M P A T U R E , A N D S P E E D V I A N M E A D A T A F O R D I S P L A Y O N T H E G P S M A P 2 0 0 6 / 2 0 1 0 . Diagram 2 - Complete Interface GPSMAP 2006C/2010C & GPS
Inhaltszusammenfassung zur Seite Nr. 10
INSTALLATION INSTRUCTIONS Final Wiring Connection Once all the wiring is complete, plug the 18-pin harness into the center connector on the backside of the GPSMAP 2006/2010. The 5-pin port on the right side is intended for future interfacing features and does not require connection at this time. With power applied to the circuit, you may test the installation by pressing the POWER key on the front of the unit. See the Owner’s Manual for steps on initializing the receiver. 5-Pin Connecto
Inhaltszusammenfassung zur Seite Nr. 11
INSTALLATION INSTRUCTIONS FLUSH MOUNT DRILLING TEMPLATE Drill using a 11/64” or 4.5 mm drill bit Dill this 3/4” or 19 mm hole if the coax is going to be installed through the mounting panel GPSMAP 2006C/2010C & GPS 17 11
Inhaltszusammenfassung zur Seite Nr. 12
© Copyright 2005 Garmin Ltd. or its subsidiaries Garmin International, Inc. st 1200 East 151 Street, Olathe, Kansas 66062, U.S.A. Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K. Garmin Corporation nd No. 68, Jangshu 2 Road, Shijr, Taipei County, Taiwan www.garmin.com Part Number 190-00228-01 Rev. F
