Inhaltszusammenfassung zur Seite Nr. 1
Adtron Corporation
I35MB - 3.5”
I35MB - 3.5”
Mirrored Hard Disk
Mirrored Hard Disk
Operations Manual
Operations Manual
March 2006
Rev. 003
PN: 610200094
Inhaltszusammenfassung zur Seite Nr. 2
ESD Warning Before handling the I35MB, or any media associated with the I35MB, ensure that you are working in an ESD-safe environment. Notice This manual describes the features of the Adtron I35MB. Adtron reserves the right to modify, amend, or in any way change the contents and/or products described herein, at any time, without notification. The information contained in this document is provided for refere
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents Introduction 1 Aborting a button press 14 I35MB Features 1 Using the I35MB Rail Kit 15 Related Documents 2 S.M.A.R.T. (Self-Monitoring, Analysis and I35MB Jumper Settings 2 Reporting Technology) Attributes 16 Setting Master/Slave and Cable Select 3 S.M.A.R.T Attribute Table 17 Setting a Remote-Mounted Activity LED 3 S.M.A.R.T Attribute Notes 18 Interface Connectors 4 LED Indicators 19 I35MB Installation 4 IDLE State – No host access 19 Introduction 4 ACT
Inhaltszusammenfassung zur Seite Nr. 4
Adtron I35MB Operations Manual Introduction The Adtron™ Diskpak™ Model I35MB with Adtron ActiveRAID™ technology incorporates RAID-1 mirroring in a 3.5-inch hard disk form factor. RAID-1 mirroring between two hard disk drives provides data redundancy and rebuild independent from the host CPU. With both disk drives functioning properly, the I35MB keeps both disk drives automatically updated. If one of the drives fails, the system continues to operate on a single disk drive until the I35M
Inhaltszusammenfassung zur Seite Nr. 5
Adtron I35MB Operations Manual Related Documents • ANSI NCITS 340-2000 ATA/ATAPI-5 Specification • I35MB Product Specification • I35MB Installation Manual Static Sensitive – The I35MB is a static sensitive device. While setting jumpers, take precautions to ensure that static does not discharge into the I35MB. I35MB Jumper Settings The master/slave and remote LED jumper is located on the front of the I35MB, between the IDE and power connectors. This jumper is used to set master, s
Inhaltszusammenfassung zur Seite Nr. 6
Adtron I35MB Operations Manual Setting Master/Slave and Cable Select This IDE jumper is only for the configuration of master, slave, cable select and to mount a remote Activity LED. Figure 3 shows the pins of the IDE jumper on the I35MB. 3 7 5 1 8 4 2 2 6 Master Setting 7 5 3 1 8 6 4 4 2 Slave Setting 7 5 3 1 2 8 6 4 4 2 Cable Select Setting Figure 3 IDE Jumper When a jumper is placed on pins 3 and 4, the I35MB is the master device (default). With a jumper placed on pins 1 and 2, th
Inhaltszusammenfassung zur Seite Nr. 7
Adtron I35MB Operations Manual Interface Connectors The I35MB has an interface connector located on the front panel. Using an 80- conductor cable (40-pin connector); connect the I35MB to the primary or secondary ports on the IDE controller. Plug a power cable from the computer’s power supply into the I35MB power connector. The I35MB does not require 12V. Refer to the Figure below, for the location 40-pin connector and power supply. 4-pin Power 40-pin connector connector Figure 5 I35
Inhaltszusammenfassung zur Seite Nr. 8
Adtron I35MB Operations Manual Inserting the I35MB To install the I35MB in the hard disk drive bay: 1. Power down the computer and remove the cover. 2. Make sure that you are properly grounded. 3. Set the master/slave to desired configurations. By default, the I35MB is set to master. 4. Select a 3.5-inch drive bay that houses either a floppy or hard disk. If the chassis provides a front removable panel, the buzzer reset and fault LEDs can be viewed by removing the plastic panel on th
Inhaltszusammenfassung zur Seite Nr. 9
Adtron I35MB Operations Manual Removing the I35MB To remove the I35MB from the hard disk drive bay: 1. Make sure that you are properly grounded. 2. Power down the computer. 3. Remove the chassis casing. 4. Disconnect the 80-conductor cable and the computer power supply cable from the I35MB. 5. Unfasten the mounting screws and remove the I35MB from the disk drive bay. Basic Operation The I35MB operates as a storage subsystem that can be used as a boot device or as additional sto
Inhaltszusammenfassung zur Seite Nr. 10
Adtron I35MB Operations Manual I35MB LEDs and Mirror Control Buttons Activity LED Bank 0 Fault LED D10 D12 Bank 1 Access LED Bank 0 Access LED D13 Bank 1 Fault LED D11 D14 S4 S2 S3 Buzzer Reset Bank 0 Mirror Control Bank 1 Mirror Control Figure 7 LEDs and Mirror controls The LEDs are used to indicate individual Bank status (access/fault), media activity (read/writes) and Mirror status. Table 1 describes LED states, mirror status and controls. The following table describes the LED sta
Inhaltszusammenfassung zur Seite Nr. 11
Adtron I35MB Operations Manual Mirror Control Button Functions The following figure shows the location of the mirror control buttons and LEDs on the I35MB. Bank 1 Mirror control Buzzer Reset Bank 0 Mirror control Figure 8 Mirror Control Button operations The following table describes the different operations using the Mirror Control button on either bank. Press and hold Mirror Control button to activate the functions listed in Table 2. Button Press Duration Bank Access LED Feedback F
Inhaltszusammenfassung zur Seite Nr. 12
Adtron I35MB Operations Manual Adtron recommends having a system back-up available prior to managing hard or soft faults. Bank Hard Faults Hard fault errors may originate from any one of the following: • Write errors • Track 0 Not Found read error • HDD Timeout after a command If a hard fault occurs on one bank, the I35MB continues to read and write data to the other functioning bank. The I35MB is running in a degraded mode, which should be corrected as soon as possible. When the I3
Inhaltszusammenfassung zur Seite Nr. 13
Adtron I35MB Operations Manual Rebuilding the faulted drive may take several hours, depending on the size of the media and may result in a hard fault if the drive cannot “map” around any “bad” sectors. While rebuilding can result in a reliable storage device and workable drive, Adtron recommends replacing the drive in the field that exhibits a soft fault and then rebuilding and testing this drive in a non- critical test environment to determine if this drive can be used as a spare. T
Inhaltszusammenfassung zur Seite Nr. 14
Adtron I35MB Operations Manual 3. Note the bank number, 0 or 1, with the fault LED turned solid orange. This is the bank that requires attention. 4. Power down the computer. 5. Remove the computer cover and locate the I35MB in the disk drive bay. 6. Disconnect the power supply and 80-conductor cable from the I35MB. 7. Unscrew the chassis mounting screws and slide the I35MB out of the disk drive bay. 8. On the side opposite the flex cables, loosen the retaining screw for the faulted d
Inhaltszusammenfassung zur Seite Nr. 15
Adtron I35MB Operations Manual 12. Before the disk drive is fully seated (approximately ¼ of an inch to the drive being fully seated) re-attach the flex cable to the disk drive. Refer to Figure 10 for a view of this procedure. Carefully align and slowly attach. Pay close attention to mounting the flex cable. Ignoring this procedure and caution can lead to damage in future operations. 13. Tighten the retaining screw for the new disk drive. 14. The I35MB may be re-inserted in the disk dri
Inhaltszusammenfassung zur Seite Nr. 16
Adtron I35MB Operations Manual Rebuilding a bank After a bank has been replaced, a rebuild must be performed. To start a Bank Rebuild, press the mirror control button between 5 and 10 seconds on the off-line bank. Release the button when the Access LED starts flashing at 2 blinks per second. The rebuild process begins, indicated by the Access LED turning solid green and the Fault LED flashing green. When complete, the Fault LED changes from flashing green to off. It is faster to do
Inhaltszusammenfassung zur Seite Nr. 17
Adtron I35MB Operations Manual Examples: A new I35MB is installed in the field with two 20GB capacity media for 20GB of mirrored storage. Bank 1 requires replacement. A 10GB media is installed and the button pressed for rebuild. Rebuild will not start and the mirror remains broken. A 40GB media is then inserted in Bank 1. The rebuild copies the data from the Bank 0 20GB drive to the new drive in Bank 1. The I35MB remains a 20GB mirrored device. Bank 0 media is replaced with a
Inhaltszusammenfassung zur Seite Nr. 18
Adtron I35MB Operations Manual Using the I35MB Rail Kit The following steps describe the process to disassemble and reassemble hard disk drives on the I35MB. Attention to individual instructions is necessary to ensure functionality and avoid damage to the device. Please contact Adtron Sales if assembling hard disk drives other than those provided by Adtron, and refer to the section of this manual titled, Using Different Size Media. Refer to Appendix # 1 for a list of supplies that are i
Inhaltszusammenfassung zur Seite Nr. 19
Adtron I35MB Operations Manual S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) Attributes The Adtron Diskpak I35MB incorporates an array of S.M.A.R.T. attributes and capabilities that provide significant amounts of information relating to the life history of the hard disk drive (HDD). S.M.A.R.T. is a monitoring system for computer (HDDs) to detect and report on various indicators of reliability, with the intent of anticipating failures. The user or system administrator c
Inhaltszusammenfassung zur Seite Nr. 20
Adtron I35MB Operations Manual S.M.A.R.T Attribute Table S.M.A.R.T attributes are vendor specific parameters that are used in evaluating the status of the device. Adtron specific S.M.A.R.T attributes are listed below. Many tools used to display S.M.A.R.T. attributes may not recognize Adtron specific attributes. Refer to Table 3 to identify Adtron specific S.M.A.R.T. attributes. Attribute Name Value Raw Data Threshold Number (8 bits) (eight, 8-bit bytes) (8 bits) 9 (0x09) Power o
