Inhaltszusammenfassung zur Seite Nr. 1
INST ALLA TION
IS210 Series
®
Camclosure
Integrated Camera System
C3428M-A (1/08)
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Parts List . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 4
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 7. Only use attachments/accessories specified by the manufacturer. 8. Use only with the cart, stand, tripod, bracket,
Inhaltszusammenfassung zur Seite Nr. 5
REGULATORY NOTICES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provi
Inhaltszusammenfassung zur Seite Nr. 6
Description ® The IS210 Series Camclosure is a wedge-style integrated camera system that is quick and easy to install. The system is designed to mount directly to a wall or ceiling, or to a corner with the IS210-CM corner mount. The IS210 system is shipped fully assembled. System components include a cover, base with camera and lens, and a mounting plate (refer to Figure 1). PARTS LIST Qty Description 1 Camclosure integrated camera system 1 Hole plug 1 Hollow screwdriver bit (1/8-inch) COVER
Inhaltszusammenfassung zur Seite Nr. 7
Installation PREPARE MOUNTING SURFACE 1. Remove the cover of the IS210. Use the screwdriver bit (supplied) to loosen the three tamperproof screws, and then lift the cover from the base. 2. Remove the camera assembly from the base by removing the Phillips screws on each side of the camera assembly (refer to Figure 2). CAMERA ASSEMBLY PHILLIPS SCREW Figure 2. Removing Camera Module 3. Remove the base from the mounting plate by removing the three 8-32 x 0.375-inch screws and washers. Lift the b
Inhaltszusammenfassung zur Seite Nr. 8
FIXED MOUNTING PATTERN Figure 3. Fixed Mounting Pattern ADJUSTABLE MOUNTING PATTERN Figure 4. Adjustable Mounting Pattern 8 C3428M-A (1/08)
Inhaltszusammenfassung zur Seite Nr. 9
INSTALL BASE WITHOUT CONDUIT 1. Pull the power and video wiring for the camera through the mounting surface and then through the wiring hole in the mounting plate. Fasten the mounting plate to the mounting surface with #8 stainless steel screws (not supplied) of the appropriate length. Adjustable mounting pattern only: Adjust the angle of the base before tightening the mounting hardware. 2. Connect the power input wires to the power wires located on the bottom of the IS210 base. Refer to Tab
Inhaltszusammenfassung zur Seite Nr. 10
Figure 5. Removing the Wiring Plug 4. Insert the hole plug (supplied) into the hole in the base of the Camclosure (refer to Figure 6). HOLE PLUG Figure 6. Installing the Hole Plug 5. Pull the wiring through the conduit opening (refer to Figure 7 on page 11): a. Use a 1/16-inch hex head wrench to loosen the hex head set screw. b. Use a screwdriver to remove the conduit cover. c. Pull the power wires and video cable through the conduit opening. 10 C3428M-A (1/08)
Inhaltszusammenfassung zur Seite Nr. 11
CONDUIT COVER HEX HEAD INSET SCREW 1/16-INCH HEX HEAD WRENCH Figure 7. Removing the Conduit Cover 6. Install a 0.75-inch (1.91 cm) conduit connector in the conduit opening. Line up the mounting holes in the base with the mounting holes of the mounting plate. Attach the base to the mounting plate with the three 8-32 x 0.375-inch screws and washers previously removed. 7. Attach the base to the conduit and then connect the power input wires to the power wires of the IS210 Camclosure. Refer to t
Inhaltszusammenfassung zur Seite Nr. 12
REINSTALL CAMERA MODULE Reinstall the camera module (refer to Figure 8). Make sure the top of the camera is oriented properly; the lens housing contains a label that reads TOP. NOTE: To prevent damage to the camera or lens, install the camera in the correct hole positions of the mounting bracket. MOUNT CAMERA HERE DO NOT USE Figure 8. Camera Installation ADJUST POSITION 1. Turn on power to the camera and monitor. WARNING: Heater elements could be hot! When camera power is on, use caution when
Inhaltszusammenfassung zur Seite Nr. 13
DN/CH SERIES ADJUSTMENTS Refer to Figure 10 to adjust the IS210-DN or IS210-CH model. Figure 10. Adjusting the IS210-DN/CH Series Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW4-1: Automatic Gain Control The automatic gain control (AGC) adjusts the image automatically to compensate for changes in light levels. Set SW4-1 to ON to enable AGC. Set it to OFF to disable AGC. The default setting is ON. SW4-2: Backlight Compensation The backlight com
Inhaltszusammenfassung zur Seite Nr. 14
SW4-4: Flickerless In certain lighting conditions, a flicker in the light source may affect camera operation. Flickering can be caused by a number of conditions, including the quality of the source power and the age and type of fluorescent bulbs and ballasts. Set SW4-4 to enable flickerless operation. The camera removes the effects of flickering and the shutter speed is set to 1/120 (NTSC) or 1/100 (PAL). Set SW4-4 to disable flickerless operation. This is the default setting. NOTE: If you en
Inhaltszusammenfassung zur Seite Nr. 15
Adjusting Vertical Phase You may need two people when synchronizing the cameras: one at the camera, the other at the monitor to observe the vertical roll and the effect of any camera adjustments. To synchronize the cameras: 1. Choose a reference camera to which all other cameras will be phased. 2. Select the camera to synchronize. Use buttons SW1 and SW2 to synchronize the camera to the reference camera (refer to Figure 10 on page 13). SW1 increases vertical phase; SW2 decreases vertical phas
Inhaltszusammenfassung zur Seite Nr. 16
DAY/NIGHT OPERATION NOTE: This section only applies to DN model cameras. DN model cameras regularly check the brightness level of the field of view to determine when to switch between day (color) and night (black-white) operation. Actual brightness threshold levels are affected by camera angle, amount of zoom, field of view, lens, and type of lighting. The switching process lasts from 7 to 10 seconds. Figure 10 on page 13 and Table A on page 9 show how the camera switches between color and bl
Inhaltszusammenfassung zur Seite Nr. 17
DW/CW SERIES (WIDE DYNAMIC RANGE) ADJUSTMENTS Refer to Figure 12 to adjust the IS210-DW or IS210-CW model. SW1 DEFAULT SWITCH POSITION R7 Figure 12. Adjusting the IS210-DW/CW Series Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW1-1: Video Format Set SW1-1 to ON for NTSC. Set it to OFF for PAL. The default setting is ON. SW1-2: Line Sync When multiple cameras are connected to the same switching device, vertical roll may occur on the monitor. AC
Inhaltszusammenfassung zur Seite Nr. 18
SW1-4: Auto White Balance/Manual White Balance Auto white balance (AWB) is enabled by default (ON). To manually set and lock the white balance: 1. Set SW1-4 to ON. 2. Hold a white background in front of the lens until the video is all white. 3. While holding the background in place, set SW1-4 to OFF. A green block and a white block alternate briefly on the video image until the manual white balance (MWB) process is complete. SW1-5: Fluorescent/General Enable this option to adjust the camera for
Inhaltszusammenfassung zur Seite Nr. 19
SW1-8: Day/Night Operation (DW models only) NOTE: On CW models, SW1-8 is unused and does not affect camera operation. DW model cameras regularly check the brightness level of the field of view to determine when to switch between day (color) and night (black-white) operation. Use SW1-8 to set the general light levels at which the camera will automatically switch. Set SW1-8 to ON (dark) to use standard thresholds to switch between color and black-white operation. This is the default setting. Se
Inhaltszusammenfassung zur Seite Nr. 20
AUTO IRIS LEVEL ADJUSTMENT The electronics of the IS210-DW and IS210-CW Series Camclosures automatically adjust the camera to the auto iris. Auto iris level adjustments are not necessary. VERTICAL PHASE ADJUSTMENT NOTE: Use this procedure for 24 VAC operation only. When using more than one camera power supply, a brief vertical roll may occur on the monitor when switching from one camera to another. To eliminate vertical roll, reverse the 24 VAC connections on one camera. If both cameras are co
