Inhaltszusammenfassung zur Seite Nr. 1
INSTALLATION INSTRUCTIONS
Instrucciones de instalación Istruzioni di installazione
Installationsanleitung Installatie-instructies
Instruções de Instalação Instructions d´installation
Wall and Desk CPU Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
KSA-1020
Inhaltszusammenfassung zur Seite Nr. 2
KSA-1020 Installation Instructions DISCLAIMER Milestone AV Technologies, and its affiliated corporations and CAUTION: A CAUTION alerts you to the possibility of subsidiaries, (collectively, Milestone) intend to make this damage or destruction of equipment if you do not follow the manual accurate and complete. However, Milestone makes no corresponding instructions. claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possib
Inhaltszusammenfassung zur Seite Nr. 3
Installation Instructions KSA-1020 LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging losdraaie
Inhaltszusammenfassung zur Seite Nr. 4
Installation Instructions KSA-1020 TOOLS REQUIRED FOR INSTALLATION 7/64" #2 1/2" 17/64" 1/2" PARTS B(2) C(4) 3" A(1) E(2) D(1) 1/4-20 X 1 3/4" G(2) F(1) 3/8 X 1 1/4" #12 X 2 1/2" 4
Inhaltszusammenfassung zur Seite Nr. 5
Installation Instructions KSA-1020 buttons to reinstall them in the holes in which they will be ASSEMBLY AND INSTALLATION used. Installation of Protective Rubber Edging • If mounting vertically, move mounting buttons in 1. Place four strips of protective rubber edging (C) over the the four holes on top of the mount. (See Figure 3) sharp edges located on the top and bottom of the mount (A). • If mounting horizontally, move mounting buttons (See Figure 1) in the top four holes on the back. (
Inhaltszusammenfassung zur Seite Nr. 6
KSA-1020 Installation Instructions CPU’s to be installed. (See Figure 5) 8. Tighten front strap to desired tension. NOTE: Flanges may be reversed in order to allow for narrow WALL MOUNT INSTALLATION CPU’s to be installed in a secure manner. If this is done, be sure to also to remove and reinstall strap so that the buckle is facing out for easy adjustment. WARNING: FAILURE TO PROVIDE ADEQUATE STRUCTURAL STRENGTH FOR THIS MOUNT CAN 5 RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMEN
Inhaltszusammenfassung zur Seite Nr. 7
Installation Instructions KSA-1020 Site Requirements for Using Steel Studs WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for installation of display mounts onto a steel stud structure. If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation. It should also be noted that no
Inhaltszusammenfassung zur Seite Nr. 8
KSA-1020 Installation Instructions Wall Mounting Using Steel Studs or Drywall After determining the site meets the installation requirements: Steel Stud 1. Identify desired mounting location on wall. Drywall 2. Using a stud finder or similar method locate stud. 3. Align mounting holes in mount with stud making sure mounting holes are centered on stud. (See Figure 9) Plastic Cap WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUI
Inhaltszusammenfassung zur Seite Nr. 9
Installation Instructions KSA-1020 Steel Stud Drywall 12 (E) x 2 13 3 (Flag in closed position) Mounting Bracket Anchor Metal Channel Figure 15 (SIDE VIEW) Desk Mount Installation Figure 13 WARNING: Failure to provide adequate structural strength Mounting CPU to Wall for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the desk to which this component is attached can CAUTION: Overtightening screws may cause wall
Inhaltszusammenfassung zur Seite Nr. 10
KSA-1020 Installation Instructions desk 2 mounting bracket (D) 3 (F) Figure 16 3. Install 3/8 x 1 1/4" hex head lag screw (F) through bearing (D) and bracket into hole drilled in Step 2. (See Figure 16) 4. Ensure bracket flag is in the open position. 5. Insert four mounting buttons into four mounting holes on the bracket. (See Figure 17) Figure 17 6. Slide buttons into locked position within holes. 7. Move flag to closed position in order to fully secure mount to bracket. (See Figure 15) 1
Inhaltszusammenfassung zur Seite Nr. 11
Installation Instructions KSA-1020 11
Inhaltszusammenfassung zur Seite Nr. 12
KSA-1020 Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Chief Manufacturing, a division of Asia Pacific A Room 24F, Block D, Lily YinDu International Building Milestone AV Technologies LuoGang, BuJi Town, Shenzhen, CHINA. 8834-000003 P +86-755-8996 9226 ©2008 Milestone AV Technologies F +86-755
