Inhaltszusammenfassung zur Seite Nr. 1
Versa S940
Disassembly Manual
Inhaltszusammenfassung zur Seite Nr. 2
Table of contents Overview.................................................................................................................................................................3 Technician Notes....................................................................................................................................................3 Disassembly Instructions....................................................................................................................
Inhaltszusammenfassung zur Seite Nr. 3
Overview This document contains step-by-steps disassembly instructions for the Versa S940/EasyNote A7 chassis. The instructions are illustrated where necessary with images of the part that is being removed or disassembled. Furthermore, the screws that are removed are shown next to the image of the parts themselves. NEC reserves the right to make changes to the Versa S940/EasyNote A7 chassis without notice. Technician Notes Only technicians authorized by NEC Computers International BV
Inhaltszusammenfassung zur Seite Nr. 4
WARNING Hazardous Voltage Ensure that the computer is disconnected from its power source and from all There is hazardous voltage present inside the computer telecommunications links, networks, or modem when it is connect to an AC supply, even when the lines whenever the chassis cover is removed. computer’s power switch is off. Exposure to hazardous Do not operate the computer with the cover voltage could cause personal injury. To avoid risk of injury, removed. contact an Authorized Se
Inhaltszusammenfassung zur Seite Nr. 5
Removing the Battery Perform the following steps to remove the battery: 1. Make sure to power off the Versa S940/EasyNote A7. 2. Turn the unit upside down. 3. Unlock the battery and slide it out of its place as the arrow shows in Fig. 1 Fig. 1 Removing the battery NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 5
Inhaltszusammenfassung zur Seite Nr. 6
Removing the Memory Module To remove the Memory Module, first remove the battery (see Removing the Battery), then perform the following steps: 1. Release the three screws retaining the memory module cover. Fig. 2 Removing the screws retaining the memory module slot cover 2. Unclip the memory module as shown in Fig. 3 Fig. 3 Removing the memory module 3.
Inhaltszusammenfassung zur Seite Nr. 7
Removing the WLAN Card Module To remove the WLAN Card Module, first remove the Memory Module Cover (see Removing Memory Module) then perform the following steps: 1. Disconnect the wireless antenna connector and release the WLAN Card Module as shown in Error! Reference source not found. Fig. 4 WLAN Card Module 2. Lift up the WLAN Card Module and put it aside.
Inhaltszusammenfassung zur Seite Nr. 8
Removing the Hard Disk Drive To remove the hard disk drive, first remove the battery (see Removing the Battery), then perform the following steps: 1. Remove the screws as shown in Fig. 5 M2.5x8 Copper Fig. 5 Removing the Hard disk drive cover 2. Carefully pull the HDD module out from the base unit. Fig. 6 Pulling HDD module NEC Versa S940/PB
Inhaltszusammenfassung zur Seite Nr. 9
3. Remove four screws that around HDD module. M4x3 Silver Fig. 7 HDD module Note: When installing HDD, make sure the HDD module strap properly insert into base unit as shown in below picture. NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 9
Inhaltszusammenfassung zur Seite Nr. 10
Removing the Optical Disk Drive To remove the ODD, first remove the battery (see Removing the Battery) and Memory Module Cover (see Removing Memory Module) then perform the following steps: 1. Use pin to eject the optical drive via emergency eject hole as shown in Fig. 8 Fig. 8 Eject the optical drive 1. Pull the ODD module out from the base unit as shown in Fig. 9
Inhaltszusammenfassung zur Seite Nr. 11
Removing the CPU To remove the CPU first remove the battery (see Removing the Battery) then perform the following steps: 1. Losses four screws that retaining the CPU cover as shown in Fig. 10 Fig. 10 Removing the screws retaining CPU cover 2. Remove the CPU Fan screws, disconnect the CPU Fan connector and unscrew screws on CPU Heat Sink in descending order (3 2 1) as shown in Fig. 11 A = M
Inhaltszusammenfassung zur Seite Nr. 12
3. Unlock the CPU from the CPU socket and lift up the CPU carefully. Fig. 12 Unlocking the CPU NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 12
Inhaltszusammenfassung zur Seite Nr. 13
Removing the Keyboard To remove the Keyboard, first remove the battery (see Removing the Battery), then perform the following steps: 1. Release two screws on keyboard cover as shown in Fig. 13 M2x4.5 Black Fig. 13 Releasing the keyboard cover 2. Lift up the keyboard cover carefully as shown in Fig. 14 Fig. 14 Lifting up the Keyboard Cover
Inhaltszusammenfassung zur Seite Nr. 14
3. Unscrew two screws at the bottom as shown in Fig. 15 A = M2.5x5 Black B= M2.5x6 Copper Fig. 15 Unscrewing Keyboard screws Caution: If using wrong screws during keyboard assemble might result damage to keyboard. Thus please mark those screws carefully during dissemble. 4. Flip over the unit and release remaining screw holding keyboard as shown in Fig. 16 M2.5x3 Silver Fig. 16 Screw
Inhaltszusammenfassung zur Seite Nr. 15
5. Lift up the keyboard and disconnect it from the system as shown in Fig. 17 Fig. 17 Disconnecting the keyboard flat cable Removing the LCD Module To remove the LCD Module first remove the battery (see Removing the Battery), remove WLAN Card Module (see Removing WLAN Card Module)and remove the Keyboard (see Removing the Keyboard) then perform the following steps: 1. Release LCD cable from base u
Inhaltszusammenfassung zur Seite Nr. 16
2. Disconnect LCD Cable Connection and remove four screws retaining the Heat Plate as shown in Fig. 19 M2.5x6 Silver Fig. 19 Removing the screws retaining the LCD module 3. Carefully lift up the LCD Module. NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 16
Inhaltszusammenfassung zur Seite Nr. 17
Removing the LCD Panel To remove the LCD panel, first remove the LCD module (see Removing the LCD Module), then perform the following steps: 1. Use a pin to remove the rubber cover on the LCD module as shown in Fig. 20 2. Remove all screws as shown in Fig. 20 and remove carefully the LCD cover. A = M2x7 Silver B = M2.5x5 Black Fig. 20 Removing the rubber covers & screws on the LCD Module 3. Carefully removing the
Inhaltszusammenfassung zur Seite Nr. 18
4. Release four screws at the both side of LCD hinge as shown in Fig. 22 M2.5x4 Copper Fig. 22 Unscrew LCD Penal 5. Disconnect all connectors on inverter board as shown in Fig. 23 Fig. 23 Removing the Inverter Board 6. Carefully lift up the LCD panel. 7. Remove the screws at both sides of the LCD panel in order to release the LCD hinges as shown in Fig. 24 M2x4
Inhaltszusammenfassung zur Seite Nr. 19
Removing the Top Cover To remove the Top Cover , first remove the battery (see Removing the Battery), remove the HDD (see Removing the Hard Disk Drive), remove the Optical Disk Drive (see Removing the Optical Disk Drive), remove the CPU (see Removing the CPU)remove the Keyboard (see Removing the Keyboard) and remove the LCD Module (see Removing the LCD Module) then perform the following steps: 1. Remove all screws on the bottom of the base unit as shown in Fig. 25
Inhaltszusammenfassung zur Seite Nr. 20
3. Disconnect the Touch Pad Connector and remove all screws as shown in Fig. 27 A = M2.5x4 Silver B = M2.5x5 Silver Fig. 27 Top cover 4. Carefully lift up the Top Cover. NEC Versa S940/PB EasyNote A7 Disassembly Manual Page 20
