Inhaltszusammenfassung zur Seite Nr. 1
2-190-706-13 (1)
Digital Powered
Mixer
Operating Instructions
Before operating the unit, please read this manual thoroughly and retain it for future reference.
SRP-X500P
© 2004 Sony Corporation
Inhaltszusammenfassung zur Seite Nr. 2
To avoid electrical shock, do not open the Important Safety Instructions cabinet. Refer servicing to qualified personnel only. • Read these instructions. Keep these instructions. THIS APPARATUS MUST BE EARTHED. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat
Inhaltszusammenfassung zur Seite Nr. 3
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to tr
Inhaltszusammenfassung zur Seite Nr. 4
Table of Contents Overview.................................................................................6 Features ...................................................................................... 6 The SRP-X500P manuals........................................................... 6 Using the supplied CD-ROM..................................................... 6 Operating Conditions............................................................7 Precautions ...................................
Inhaltszusammenfassung zur Seite Nr. 5
Connector specifications .......................................................... 32 Troubleshooting ..................................................................35 5
Inhaltszusammenfassung zur Seite Nr. 6
external personal computer or system controller to control the SRP-X500P. Overview REMOTE PARALLEL connector Input signal selection, volume control and scene control of the SRP-X500P can be performed via the input pins. Through the output pins, remote control of the Features environmental equipment such as a screen and lighting The SRP-X500P is a versatile powered mixer which equipment, and the status display of the SRP-X500P can incorporates an audio mixer, RGB/video switcher, be carri
Inhaltszusammenfassung zur Seite Nr. 7
SRP-X500P Manager This is a program for setting the SRP-X500P parameters Operating Conditions from a PC. The English and the Simplified Chinese versions are provided. The recommended operating environment for using the How to open files SRP-X500P Manager is as follows. OS Microsoft Windows Millennium Edition 1 Insert the supplied CD-ROM into the CD-ROM drive, Microsoft Windows 2000 Professional then click “My Computer.” Microsoft Windows XP Professional 2 Double-click “SRP-X500P.” Microsoft
Inhaltszusammenfassung zur Seite Nr. 8
Precautions The SRP-X500P must be used within a temperature range of 0°C to 40°C (32°F to 104°F). Operating the SRP-X500P near electrical equipment (motors, transformers, or dimmers) may cause it to be affected by electromagnetic induction. Keep the SRP- X500P as far from such equipment as possible. The presence of the lighting equipment may produce electrical interference over a very wide frequency range. Position the antennas and the wireless microphones to be used with the SRP-X50
Inhaltszusammenfassung zur Seite Nr. 9
Location and Function of Parts Front panel 1 23 45 6 7 8 qkqj qh qg qf qd qs qa q; 9 (In the figure above, the two blank panels are removed.) A POWER switch UWP-X1/X2 (not supplied)) for using wireless Turns the SRP-X500P on and off. microphones. With the SRP-X500P Manager software, you can set a parameter that will cause the projector or display monitor For details on installing tuner units, see “Installing the connected to the SRP-X500P to turn on or enter standby tuner units” (page 14).
Inhaltszusammenfassung zur Seite Nr. 10
MIC 3: Adjusts the level of the signal input from the MIC I MASTER control INPUT 3 connector. Adjusts the output level of the assigned channels. MIC 4: Adjusts the level of the signal input from the MIC With the SRP-X500P Manager software, you can specify INPUT 4 connector. which output channels are controlled by the MASTER LINE: Adjusts the level of the signals input from the control. LINE IN connectors. The MASTER control is factory-set to control the output AV/RGB: Adjusts the level of
Inhaltszusammenfassung zur Seite Nr. 11
controls so that the REF. indicators light up yellow Note intermittently. For control of an LCD Data Projector VPL-PX15, use the FEED BACK REDUCER (howling suppressor) CONTROL S connectors instead of the PROJECTOR buttons: Used to turn the howling noise reducing CONTROL RS-232C connector. function on or off, and to make settings for the function. The buttons light up green when the function N SYSTEM TYPE selector is turned on. Can be set to positions 1-9, according to the speaker confi
Inhaltszusammenfassung zur Seite Nr. 12
Rear panel 1 23 4 5 1 6 7 3# 3# 3# 3 # 3# qf qd qs qa 0 9 8 A ANT IN a/b connectors (BNC type) B PROJECTOR CONTROL CONTROL S IN/OUT Connect antennas for the tuner unit installed in the SRP- connectors (stereo mini jack) X500P. Only the supplied antennas or the UHF Antenna Used to control the LCD Data Projector VPL-PX15 AN-820 (not supplied) can be used. exclusively. For details on the function of this connector, see Notes “PROJECTOR CONTROL CONTROL S IN/OUT If the antenna is not installed
Inhaltszusammenfassung zur Seite Nr. 13
Input pins K AV/RGB INPUT audio connectors (A to E) (phono jack) Connectable device Remarks Connect to the audio output connectors of the devices Switch - whose video output is connected to the N AV/RGB INPUT video connectors on the SRP-X500P. Volume With 10 kΩ , B-curve When connecting a device, be sure that each output Emergency broadcast Connected via relay connector on the device is connected to the AV/RGB system INPUT video and audio connector on the SRP-X500P with the corresponding l
Inhaltszusammenfassung zur Seite Nr. 14
that of the tuner unit, or that the battery in the microphone is running down. Installation To remove the tuner unit Pull the latch securing the tuner unit to the side and pull out Installing the tuner units the tuner unit. Up to two WRU-806 UHF Synthesizer Tuner Units (not Tuner unit supplied) or two URX-M1 Tuner Units included in the UWP-X1/X2 (not supplied) can be installed in the SRP- X500P. Notes To prevent the production of noise, be sure to turn the SRP-X500P off before installing
Inhaltszusammenfassung zur Seite Nr. 15
Note GP button + button When removing the blank panels to the SRP-X500P, be sure to start with the small panel. Rack mounting RF indicator About the rack Use an EIA-standard 19-inch rack with a depth of 450 mm or more. CH button – button Use four screws of the same diameter as the rack screw holes and with an effective length of 12 mm or more to 1 Turn on the SRP-X500P. mount the SRP-X500P into the rack. 2 Press and hold down the GP button, and press the + or – button to select a group. Rac
Inhaltszusammenfassung zur Seite Nr. 16
Releasing the buttons automatically cancels the group and channel selection mode, and the currently displayed group is selected. Refer to “Wireless Microphone System Frequency List” supplied with the WRU-806. 3 Press and hold down the CH button, and press the + or – button in 3 seconds to select a channel. Similer to step 2, each time you press the + or – button, the CH indication changes in the order shown in the group and reception channel list. Refer to “Wireless Microphone System Frequ
Inhaltszusammenfassung zur Seite Nr. 17
System Configurations and Speaker Connections Sample configuration using the SRP-X500P factory-settings In this configuration, the SRP-X500P can be used without having to change the settings with the supplied SRP-X500P Manager software. AN-820 UHF Antenna or the Projector supplied antenna PROJECTOR CONTROL RS-232C INPUT AN-820 UHF Antenna or the supplied antenna Transmitter Wireless Front Front microphone speaker speaker Transmitter LINE (L) (R) OUT Document PC Wireless microphone camera
Inhaltszusammenfassung zur Seite Nr. 18
Sample system configuration with a custom operation panel and environmental equipment connected In this configuration, the SRP-X500P can be controlled by a custom operation panel or an external system controller. AN-820 UHF Antenna or the Projector supplied antenna Transmitter PROJECTOR CONTROL RS-232C INPUT AN-820 UHF Antenna or the Wireless supplied microphone antenna Custom operation panel Front speaker Operation (L) terminal Document camera Transmitter VIDEO OUT Wireless micropho
Inhaltszusammenfassung zur Seite Nr. 19
To connect low-impedance speakers to the Speaker connection SPEAKERS CH-3/4 terminals Only speakers with low impedance (4 to 16Ω ) can be Set the SYSTEM TYPE selector to “2,” “5,” “6,” “7,” “8,” connected to the SPEAKERS CH-1/2 terminals. or “9.” Speakers of high or low impedance can be connected to the Or, set the SYSTEM TYPE selector to “0” and use the SPEAKERS CH-3/4 terminals by setting the SYSTEM SRP-X500P Manager software to make setting. TYPE selector. Connect the speakers as shown in
Inhaltszusammenfassung zur Seite Nr. 20
SPEAKERS LINE OUT SP 1 SP 2 SP 3 SP 4 CH-1 CH-2 CH-3 CH-4 MIC IN ON/OFF OFF OFF ON ON ON ON ON ON LEVEL 0dB 0dB 0dB 0dB 0dB 0dB 0dB 0dB LINE IN ON/OFF ON OFF OFF OFF ON OFF OFF OFF L LEVEL 0dB 0dB 0dB 0dB 0dB 0dB 0dB 0dB LINE IN ON/OFF OFF ON OFF OFF OFF ON OFF OFF R LEVEL 0dB 0dB 0dB 0dB 0dB 0dB 0dB 0dB AV/RGB ON/OFF ON OFF OFF OFF ON OFF ON OFF IN L Audio from the AV components is output from the front LEVEL 0dB 0dB 0dB 0dB 0dB 0dB 0dB 0dB speakers in stereo, and audio from the microphones is
