Inhaltszusammenfassung zur Seite Nr. 1
Operating Instructions Model NB0050
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury, death
and/or property damage! Retain instructions for future reference.
CAMPBELL
Finishing Nailer
HAUSFELD
Description
This nailer is designed for trimwork, interior molding, baseboards, pane
Inhaltszusammenfassung zur Seite Nr. 2
Operating Instructions Model NB0050 l Always check l Do not operate Warning Continued the work con- or allow anyone l Never place ! tact element else to operate WARNING your hand or (WCE) trip the nailer if any any part of mechanism of warnings or your body in the nailer. A warning labels the nail dis- nail could acci- are not legible. charge area of dentally be dri- Warnings or the nailer. It is ven if the trig- warning labels are located on the possible for the gering mechanism is not working
Inhaltszusammenfassung zur Seite Nr. 3
Operating Instructions Model NB0050 2. An oiler can be SINGLE CYCLE MODE Using The Nailer used to provide This method is rec- Read this manual and understand oil circulation ommended when all safety warnings and instruc- through the precise nail place- tions before operating the nailer. nailer. A filter ment is required. can be used to The single cycle pin LUBRICATION remove liquid must be installed This nailer requires lubrication before and solid impurities which can rust in the nailer. This
Inhaltszusammenfassung zur Seite Nr. 4
Operating Instructions Model NB0050 Each time the 5. Unloading is the reverse of load- 5. Depress the Work Contact ing, except always disconnect the work contact Element (WCE) is air hose before proceeding. element (WCE) depressed, a nail is against the driven into the work surface ADJUSTING THE NAIL PENETRATION work surface. Care without pulling 1. Regulate the air pressure to 70 PSI 1 should be taken the trigger. The nailer MUST NOT at the nailer. when using this method because a nail cycle. D
Inhaltszusammenfassung zur Seite Nr. 5
Operating Instructions Model NB0050 Technical Support COLORMATCH™ System 4. The driver cover plate can Should you have any questions regard- The Campbell Hausfeld Finishing Nailer now be rotat- ing the operation or repair of this nail- has a unique COLORMATCH™ stripe. ed, exposing er, please call our Nailer Hotline at Look for the COLORMATCH™ stripe to the jammed 1-800-543-6400 for assistance. If you choose the right Campbell Hausfeld fastener. are calling from Ohio or outside of the fasteners
Inhaltszusammenfassung zur Seite Nr. 6
Operating Instructions Model NB0050 Troubleshooting Guide Stop using nailer immediately if any of the following problems occur. Serious personal injury could result. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center. Problem Cause Solution Air leaking at trigger valve O-Rings in trigger valve housing are O-Rings must be replaced & operation of work damaged contact element must be checked Air leaking between hous- Loose screws in housing Screws n
Inhaltszusammenfassung zur Seite Nr. 7
Operating Instructions Model NB0050 Limited Warranty 1. DURATION: One year from the date of purchase by the original purchaser. 2. WHO GIVES THIS WARRANTY (WARRANTOR): The Campbell Group A Scott Fetzer Company 100 Production Drive Harrison, Ohio, 45030 Telephone: 1-800-543-6400. 3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld product. 4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld nailer. 5. W
Inhaltszusammenfassung zur Seite Nr. 8
Operating Instructions NB0050 Notes 8
