Inhaltszusammenfassung zur Seite Nr. 1
Euphonix System
Installation Guide
Document Revision: 2.4
Part Number: 840-07591-04
Release Date: September, 2003
Euphonix, Inc.
220 Portage Ave.
Palo Alto, California 94306
Phone: 650-855-0400
Fax: 650-855-0410
Web: http://www.euphonix.com
e-mail: info@euphonix.com
Inhaltszusammenfassung zur Seite Nr. 2
In the interest of continued product development, Euphonix reserves the right to make improvements in this manual and the products it describes at any time, without notice or obligation. System 5, S-5, PatchNet, eMix, EuCon, R-1, Audio Deck, Studio Hub are trademarks of Euphonix, Inc. ©2002 Euphonix, Inc. All rights reserved worldwide. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any mea
Inhaltszusammenfassung zur Seite Nr. 3
Euphonix System 5 Installation Guide Table of Contents List of Figures .........................................................................................................................v List of Tables ........................................................................................................................ vii Chapter 1: System 5 Overview ....................................................................................9 Introduction to System 5..........................
Inhaltszusammenfassung zur Seite Nr. 4
Euphonix System 5 Installation Guide Chapter 3: System 5 Components ..........................................................................33 DF64 Digital Frame ............................................................................................33 FC631 Frame Controller .........................................................................35 MM641 MADI Interface Card................................................................35 SP661 Signal Processor ..........................
Inhaltszusammenfassung zur Seite Nr. 5
Euphonix System 5 Installation Guide List of Figures 2-1 Typical Room and Equipment Layout for System 5 ........................................................20 2-2 System 5 Console ..............................................................................................................20 2-3 Console Dimensions - Top ...............................................................................................21 2-4 Console Dimensions - Side .............................................
Inhaltszusammenfassung zur Seite Nr. 6
Euphonix System 5 Installation Guide 3-17 SH612 Studio Hub ............................................................................................................48 3-18 AM713 Front Panel ..........................................................................................................49 3-19 AM713 Rear Panel ............................................................................................................50 3-20 MA703 Front Panel .........................................
Inhaltszusammenfassung zur Seite Nr. 7
Euphonix System 5 Installation Guide List of Tables 1-1 DF64 Requirements ...................................................................................................... 14 1-2 Summary of System 5 Components ............................................................................... 16 2-1 System 5 Components: Dimensions, Power Consumption, Heat Dissipation ............... 17 2-2 Fuse Ratings for System 5 Components ....................................................................
Inhaltszusammenfassung zur Seite Nr. 8
Euphonix System 5 Installation Guide viii
Inhaltszusammenfassung zur Seite Nr. 9
Euphonix System 5 Installation Guide Chapter 1: System 5 Overview This chapter explains the basic elements of any digital audio mixing system and introduces the components of System 5. It concludes with a section explaining how to estimate your system’s requirements. Chapter 2: Interconnecting System Components illustrates how to connect the components, where to locate them, and lists technical information about the components. Chapter 3: System 5 Components presents relevant details about ea
Inhaltszusammenfassung zur Seite Nr. 10
Euphonix System 5 Installation Guide System 5 Overview Inputs System 5 inputs may be mono, stereo, or any format up to 7.1, which means that a single input may use one to eight logical channels. Physical Faders Each CM408 Eight-channel Module contains eight physical faders. Each fader can control two inputs using a Swap button that switches the fader between the Swap and Main inputs. Layouts Inputs are assigned to physical faders by using Layouts. Numerous Layouts can be easily stored and
Inhaltszusammenfassung zur Seite Nr. 11
Euphonix System 5 Installation Guide System 5 Overview Digital I/O All digital I/O is converted to and from MADI format via the DM714 AES/EBU to MADI Converter, and the MD704 MADI to AES/EBU Converter. Each unit’s main I/O handles 24 signals (12 AES/EBU pairs) and also contains an auxiliary stereo analog input or output, and an auxiliary stereo digital input or output (AES/EBU and S/PDIF). All digital inputs have built in Sample Rate Converters. Format Conversion The FC727 is a bidirectiona
Inhaltszusammenfassung zur Seite Nr. 12
Euphonix System 5 Installation Guide System 5 Overview We recommend following these guidelines: • It is important to minimize the timing differences between signal paths to avoid cumulative timing errors. It is good system engineering practice to send sync signals to all system components from one source. • Sync signals should not be looped and each distribution amplifier should be fed directly from the master clock source. • Drawings in this installation guide show the use of Word Clock. Th
Inhaltszusammenfassung zur Seite Nr. 13
Euphonix System 5 Installation Guide System 5 Overview TCC Control The PC253i Interface computer also requires no user interaction. It connects to the MC524 Monitor Interface and up to seven ML530 Mic/Line Interfaces via TCC connection. Machine Control The TT007 provides machine control of three serial 9-pin devices, MTC, and LTC. The TT007 connects via MIDI in and out to a MOTU MIDI I/F. This interface is connected to the PC253i Interface Computer, MMC, LYNX Net, and ESBus via the parallel p
Inhaltszusammenfassung zur Seite Nr. 14
Euphonix System 5 Installation Guide System 5 Overview Estimating System Requirements This section helps estimate the system requirements for a particular installation. Contact a Euphonix representative for an exact specification. Use following categories to determine the System 5 components necessary for your studio. Most of the studio details considered here are relevant to any digital mixing system. Number of DF64 Digital Frames Some examples of Mixer Models and their relationship to the
Inhaltszusammenfassung zur Seite Nr. 15
Euphonix System 5 Installation Guide System 5 Overview I/O Specification When considering I/O requirements, count the number of analog and AES/EBU inputs and outputs required to hook up all equipment and auxiliary panels for extra equipment. Do not specify I/O from the console perspective. For example, it is not efficient to specify one an- alog input and one analog output to be used as an insert point for each channel input. For microphone preamps, count the maximum number of preamps require
Inhaltszusammenfassung zur Seite Nr. 16
Euphonix System 5 Installation Guide System 5 Overview Table 1-2 Summary of System 5 Components Component Function Number Notes CM401 Ethernet devices. CM401 includes a Master Module These two modules make up the center section 1 of each TB Mic and expansion port for TB of the S5 console. required CM402 Expanded external switches wiring. Channel Module CM403 Powered Allows installation of joystick panner panel and optional Ethernet device film monitor panel. Console Module CM408 Contains
Inhaltszusammenfassung zur Seite Nr. 17
Euphonix System 5 Installation Guide Chapter 2: Interconnecting System Components This chapter summarizes technical information for System 5’s components, including size, weight, power consumption, cooling, and fuse requirements and shows their interconnections. To plan an installation, examine Figure 2-1 to learn about suggested equipment locations. The Sync, MADI, and Control hookup diagrams (Figure 2-10 through Figure 2-13) all show maximum cable distances. Component Specifications Table
Inhaltszusammenfassung zur Seite Nr. 18
Euphonix System 5 Installation Guide Interconnecting System Components 3.5” 17”/432 mm ML530 18.5” 17 lb 89 mm (19”/483 mm 100 W 345 BTU/hr 470 mm 7.7 kg Mic/Line Interface 2RU faceplate) 3.5” 17”/432 mm SC261 22” 23 lb 89 mm (19”/483 mm 200 W 685 BTU/hr 560 mm 10.5 kg System Computer 2RU faceplate) 3.5” 17”/432 mm PC253i 18.5” 23 lb 89 mm (19”/483 mm 200 W 685 BTU/hr 470 mm 10.5 kg Digital Pilot 2RU faceplate) 3.5” 17”432 mm PC253d 18.5” 23 lb 89 mm (19”/483 mm 200 W 685 BTU/hr 470 mm 10.
Inhaltszusammenfassung zur Seite Nr. 19
Euphonix System 5 Installation Guide Interconnecting System Components Table 2-2 Fuse Ratings for System 5 Components How to Change Component 100/115/120 VAC 220/230/240 VAC Voltage Setting CM401 T5 A T5 A autoranging CM402 T5 A T5 A autoranging CM403 T5 A T5 A autoranging CM408 T5 A T5 A autoranging MC524 6 A 3 A autoranging Monitor Interface ML530 6 A 3 A autoranging Mic/line Interface SC261 6 A 3 A autoranging System Computer PC253i 6 A 3 A autoranging Digital Pilot PC253d 6 A 3 A auto
Inhaltszusammenfassung zur Seite Nr. 20
Euphonix System 5 Installation Guide Interconnecting System Components Typical Room and Equipment Layout for System 5 Figure 2-1 Typical Room and Equipment Layout for System 5 Typical Console Layout CM424 Producer’s Three CM408 CM402 and CM401 CM403 Film and Three CM408 CM424 Producer’s Module with Eight-channel Modules Center Section Modules Panner Module Eight-channel Modules Module with Writing Surface Writing Surface Figure 2-2 System 5 Console 20
