Inhaltszusammenfassung zur Seite Nr. 1
85 Mbps
MegaPlug
Ethernet Adapter
Model #: HPE400T
User Manual
Ver 1.0
™
Solutions for the Digital Life
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents 1 Introduction 1 Package Contents 1 Features 2 System Requirements 2 Getting to Know the 4-Port Hub 3 Technical Support
Inhaltszusammenfassung zur Seite Nr. 3
Actiontec HomePlug 4-Port Hub User Manual This page left intentionally blank. i ii i
Inhaltszusammenfassung zur Seite Nr. 4
Introduction 1 Thank you for purchasing the Actiontec MegaPlug 4-Port Hub. The MegaPlug 4- Port Hub is one of the easiest ways to enjoy home or small business networking. It operates on the MegaPlug Powerline Specification Turbo standard, providing data transfer speeds up to 85 Mbps over home AC wiring. Since home power lines are the most pervasive medium in households, with multiple outlets in every room, the MegaPlug 4-Port Hub allows multiple desktop and laptop computers to be networked
Inhaltszusammenfassung zur Seite Nr. 5
Actiontec MegaPlug 4-Port Hub User Manual Chapter 1 Introduction Features s HomePlug Turbo compliant s 85 Mbps data rate (maximum) s 56-bit DES encryption s Two-pronged US power plug (fits ungrounded power outlets) s Power and Link indicators System Requirements s At least 1 available power outlet s Standard home power wiring s Computer with the following: · CD-ROM drive · IBM compatible running at 200 MHz or better · Windows 98SE, Me, 2000, or XP installed · 64 MB of RAM · Ethernet networ
Inhaltszusammenfassung zur Seite Nr. 6
Actiontec MegaPlug 4-Port Hub User Manual Chapter 1 Introduction Getting to Know the 4-Port Hub This section contains a quick description of the Hub’s external features. Front Panel The Hub’s front panel features six lights (LEDs): Power Light The Power light glows green the Hub is powered up (“On”). If the Power light is off, the Hub is powered down (“Off”). HP Light The HP light illuminates when the Hub is connected to a MegaPlug network. Ethernet Lights (1, 2, 3, 4) The Ethernet lights glo
Inhaltszusammenfassung zur Seite Nr. 7
Actiontec MegaPlug 4-Port Hub User Manual AC IN Port The AC IN port is used to connect Hub with an electrical wall socket via the included Power cable Information Sticker The information sticker (located on the bottom of the Hub) displays the MAC (Media Access Control) address, device ID, and other information about the Hub. Technical Support Actiontec Electronics prides itself on making durable, high-quality, high-perfor- mance products. If you need assistance, the Actiontec Technical Suppo
Inhaltszusammenfassung zur Seite Nr. 8
Connecting the MegaPlug Hub 2 To connect the Hub, it must be connected to a computer, plugged into a standard wall outlet, and the Configuration Utility loaded on the computer. Connecting the Hub To use the Hub properly, if should be plugged into electrical outlets, and devices (computers, printers, etc.) connected to them. Connecting a Hub to a Computer 1. Get a Hub and one Ethernet cable. 2. Insert one end of the Ethernet cable into the Ethernet port of the Hub. 3. Plug the Hub into a wall
Inhaltszusammenfassung zur Seite Nr. 9
Actiontec MegaPlug 4-Port Hub User Manual Chapter 2 Connecting the MegaPlug Hubs 5. Insert the other end of the Ethernet cable into an Ethernet port on a router/ gateway connected to a computer. Follow the instructions in the next section, “Installing the Configuration Utility.” Installing the Configuration Utility After connecting the Hub, install the Configuration Utility: 1. Insert the Installation CD in the CD-ROM drive of the computer connected to a Hub. 2. When the “Welcome” screen appea
Inhaltszusammenfassung zur Seite Nr. 10
Actiontec MegaPlug 4-Port Hub User Manual Chapter 2 Connecting the MegaPlug Hubs 4. When this window appears, click Finish. 5. Repeat for other computers connected to a Hub. The MegaPlug Hub is now connected and ready to use, and the Configuration Utility is loaded on the computers. Go to chapter 3, “Using the Configuration Utility” for information about changing the default configuration settings of the Hub. 6 7
Inhaltszusammenfassung zur Seite Nr. 11
Actiontec MegaPlug 4-Port Hub User Manual This page left intentionally blank. 8
Inhaltszusammenfassung zur Seite Nr. 12
Using the 3 Configuration Utility Once the Hub has been properly connected and installed, the user can further con- figure the Hub using the Actiontec MegaPlug Configuration Utility. The Utility also provides information about the network. To access the Utility: 1. Click Start on the desktop, then Programs. 2. From the Programs menu, find “Actiontec MegaPlug,” then select MegaPlug Configuration Utility. The Utility appears on the desktop. See the following sections for more informa- tion abou
Inhaltszusammenfassung zur Seite Nr. 13
Actiontec MegaPlug 4-Port Hub User Manual Chapter 3 Using the Configuration Utility Local Device(s) on Your Computer The list displays all MegaPlug Hubs connected to the computer. Note: If no Hub appears in the Device List, make sure the Hub ☞ is connected properly (with the appropriate Ethernet cable) to the computer. Then, unplug the Hub, and plug it back in again. If, after performing these actions, no Hub appears in the Device List, the Hub may be defective. Contact technical support.
Inhaltszusammenfassung zur Seite Nr. 14
Actiontec MegaPlug 4-Port Hub User Manual Chapter 3 Using the Configuration Utility Local Device(s) on Your Computer The list displays all MegaPlug Hubs connected to the computer. Note: If no Hub appears in the Device List, make sure the Hub ☞ is connected properly (with the appropriate Ethernet cable) to the computer. Then, unplug the Hub, and plug it back in again. If, after performing these actions, no Hub appears in the Device List, the Hub may be defective. Contact technical support.
Inhaltszusammenfassung zur Seite Nr. 15
Actiontec MegaPlug 4-Port Hub User Manual Set All Devices Click this button to encrypt all devices on the MegaPlug network. About Selecting About from the row of tabs near the top of the Utility’s window gener- ates the “About” tab. The About tab displays the MegaPlug Configuration Utility version. 12
Inhaltszusammenfassung zur Seite Nr. 16
Troubleshooting 4 This chapter contains a list of problems that may be encountered while using the MegaPlug 4-Port Hub, and techniques to solve them. Note that these techniques may not be successful in all cases. Also included is a list of frequently asked questions. Troubleshooting If the Hub is showing signs of trouble, before attempting any other troubleshoot- ing procedures, plug the Hub into a working electrical wall socket. The Power light doesn’t light up after I plug the Hub into a wal
Inhaltszusammenfassung zur Seite Nr. 17
Actiontec MegaPlug 4-Port Hub User Manual Chapter 4 Troubleshooting The Power and Link lights are on, but I can’t access the router/gateway from the computer s Try plugging the Hub in different power outlets. s Make sure all Hubs on the network are using the same security parameters. Frequently Asked Questions What’s the transfer speed over the Hub’s network? The Hub’s network transfer speed is 85 Mbps (maximum) over a standard home power line network. What’s the estimated range of the Hub’s
Inhaltszusammenfassung zur Seite Nr. 18
Actiontec MegaPlug 4-Port Hub User Manual Chapter 4 Troubleshooting Can my neighbor receive the Hub’s network signal? It is possible for a neighbor to receive the network signal. To prevent this, change the default 56-bit DES security encryption password on the Hub (see chapter 3). How do I find out what the current speed and signal strength of the Hub’s network is? Run the Hub’s Configuration Utility to show current speed and signal strength. How many Hubs do I need to set up a network? One.
Inhaltszusammenfassung zur Seite Nr. 19
Actiontec MegaPlug 4-Port Hub User Manual This page left intentionally blank. 16
Inhaltszusammenfassung zur Seite Nr. 20
Setting Up Static IP Address 5 To communicate with a MegaPlug 4-Port Hub from a computer on the network, the user may have to switch the IP address settings from DHCP-enabled to static IP, so that the computer and the Hub are on the same subnet. To set up static IP on a computer, select the operating system and follow the instructions. Note: The following procedures are based on the Hub’s factory ☞ default IP address. If the Hub’s IP address has been changed, enter the new IP address wh
