Inhaltszusammenfassung zur Seite Nr. 1
Etherlink III PCI Network Interface
Card (10BT)
3C590-TPO
Installation Guide
Inhaltszusammenfassung zur Seite Nr. 2
Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Hewlett-Packard assumes no responsibility
Inhaltszusammenfassung zur Seite Nr. 3
1 Connecting to a Netware 3.12 Server Windows for Workgroups 1 Connecting to a Netware 3.12 Server Windows for Requirements Workgroups • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0. DOS ODI - File Name: 3C5X9.COM Size: 42KB Date: 7/21/96 • DOS and MS-Windows for Workgroups 3.11 media. • Novell Netware server 3.12 that supports Net BEUI, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols. • Netware client
Inhaltszusammenfassung zur Seite Nr. 4
1 Connecting to a Netware 3.12 Server Windows for Workgroups 6 Remove the 3com cards driver diskette and insert Netware client for DOS and MS-Windows disk 1. 7 Execute INSTALL.EXE and set lines 1-5 as listed below; 8 C:\NWCLIENT 9 YES 10 YES C:\WINDOWS 11 NO 12 3COM Etherlink III Parallel Tasking Family. 13 Highlight option 6 to continue with installation. 14 When prompted, insert the corresponding disks to complete file transfer and driver installation. 15 When the install utility is finishe
Inhaltszusammenfassung zur Seite Nr. 5
1 Connecting to a Netware 3.12 Server Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0. File Name: Elnk3.VXD Size: 30KB Date: 7/18/96 • Windows 95 SR2 media. • Novell Netrware 3.12 server that supports Net BEUI, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols. Device Configuration • I/O Base Address 300 • Interrupt Request Level 10 • Boot PROM Disabled • Transceiver Type Auto Select •
Inhaltszusammenfassung zur Seite Nr. 6
1 Connecting to a Netware 3.12 Server Windows 95 SR2 9 Choose to add an adapter, click on “Add” then on “Have Disk.” 10 Insert the 3C509B drivers diskette and set path to “A:\” and hit enter. (If you have a Hewlett-Packard pre-loaded HDD, set the path statement to “C:\LANDRV\3C509B\WIN95\”) 11 High light the adapter labeled “3Com Etherlink III ISA (3C509/3C509B) in ISA Mode” and press “OK.” 12 At the “Network” dialogue box, click on the “Identification” folder. 13 Enter your “Computer Name,”
Inhaltszusammenfassung zur Seite Nr. 7
2 Connecting to a Netware 4.11 Server Windows for Workgroups 2 Connecting to a Netware 4.11 Server Windows for Requirements Workgroups • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0. DOS ODI - File Name: 3C5X9.COM Size: 42KB Date: 7/21/96 • DOS and MS-Windows for Workgroups 3.11 media. • Novell Netware server 4.11 that supports Net BEUI, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols. • Netware clien
Inhaltszusammenfassung zur Seite Nr. 8
2 Connecting to a Netware 4.11 Server Windows for Workgroups 6 Remove the 3com cards driver diskette and insert Netware client for DOS and MS-Windows disk 1. 7 Execute INSTALL.EXE and set lines 1-5 as listed below; 8 C:\NWCLIENT 9 YES 10 YES C:\WINDOWS 11 NO 12 3COM Etherlink III Parallel Tasking Family. 13 Highlight option 6 to continue with installation. 14 When prompted, insert the corresponding disks to complete file transfer and driver installation. 15 When the install utility is finish
Inhaltszusammenfassung zur Seite Nr. 9
2 Connecting to a Netware 4.11 Server Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0. File Name: Elnk3.VXD Size: 30KB Date: 7/18/96 • Windows 95 SR2 media. • Novell Netrware 4.11 server that supports Net BEUI, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols. Device Configuration • I/O Base Address 300 • Interrupt Request Level 10 • Boot PROM Disabled • Transceiver Type Auto Select •
Inhaltszusammenfassung zur Seite Nr. 10
2 Connecting to a Netware 4.11 Server Windows 95 SR2 9 Choose to add an adapter, click on “Add” then on “Have Disk.” 10 Insert the 3C509B drivers diskette and set path to “A:\” and hit enter. (If you have a Hewlett-Packard pre-loaded HDD, set the path statement to “C:\LANDRV\3C509B\WIN95\”) 11 High light the adapter labeled “3Com Etherlink III ISA (3C509/3C509B) in ISA Mode” and press “OK.” 12 At the “Network” dialogue box, click on the “Identification” folder. 13 Enter your “Computer Name,”
Inhaltszusammenfassung zur Seite Nr. 11
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11 3 Connecting to a Windows NT Server 3.51 Windows for Requirements Workgroups Ver. 3.11 • HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed. • 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0. Driver Name: Elnk3.SYS Size: 27KB Date: 7/18/96 • Microsoft Windows NT Server 3.51 machine that suppo
Inhaltszusammenfassung zur Seite Nr. 12
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11 7 After windows loads, open the “NETWORK” Program Group, and double- click on “Network Setup.” 8 Select the “Networks” button in the “Network Setup” dialog box. 9 Click on the “Install Microsoft Windows Network:” option, and click “OK.” 10 Click on the “Drivers” button from the “Network Setup” dialog box, and click on “Add Adapter”. 11 Click “OK” to accept the default choice of “Unlisted or Updated Network Adapter.” 12
Inhaltszusammenfassung zur Seite Nr. 13
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11
Inhaltszusammenfassung zur Seite Nr. 14
3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11
Inhaltszusammenfassung zur Seite Nr. 15
3 Connecting to a Windows NT Server 3.51 Windows 95 SR2 Windows 95 SR2 Requirements • HP Vectra with Windows 95 SR2. • 3COM Etherlink 3C509-B Ethernet card and drivers disk ver 5.0. Driver Name: Elnk3.Vxd Size: 30.2KB Date: 7/18/96 • DOS and MS-Windows for Workgroups 3.11 media. • Microsoft Windows NT Server 3.51 machine that supports Net BEUI, TCP/ IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols. Device Configuration • I/O Base Address 300 • Interrupt Request Level 10 • Boot PROM D
Inhaltszusammenfassung zur Seite Nr. 16
3 Connecting to a Windows NT Server 3.51 Windows 95 SR2 10 In the “Network” dialog box , click on the “Add” button . 11 In the “Select Network Component Type” dialog box, highlight “Adapter” then click on “Add.” 12 Click on “Have Disk” in the “Select Network adapters” dialog box. 13 Insert the 3COM Software “Etherlink 3C509-B Ethernet Drivers Ver. 5.0” disk into the floppy drive. 14 With the Path set to “A:\” in the “Install From Disk” dialog box click “OK”. (If you have an HP pre-loaded
Inhaltszusammenfassung zur Seite Nr. 17
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 3.51 Windows NT Requirements Workstation • HP Vectra with Microsoft Windows NT Workstation 3.51 installed. Version 3.51 • 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0. Driver Name: Elnk3.SYS Size: 27KB Date: 7/18/96 • Microsoft Windows NT Workstation 3.51 and Service Pack Media. • Microsoft Windows NT S
Inhaltszusammenfassung zur Seite Nr. 18
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 3.51 9 Double click on the “Network” icon and agree to install Windows NT Networking on your computer. 10 Insert the Windows NT Workstaion CD. 11 In “Windows NT Setup”, enter the path to your NT files and click on “Continue.” (If you have an HP preloaded HDD, set path to “C:\I386”) 12 Click on “Do Not Detect” from the “ Network Adapter Card Detection” dialog box, and click on “Continue” in the second “Network Adapter
Inhaltszusammenfassung zur Seite Nr. 19
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 3.51 24 To complete the installation, remove the floppy disk , and click on “Restart Computer” button in the “Windows NT Workstation Networking Setup” dialog box.
Inhaltszusammenfassung zur Seite Nr. 20
3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 3.51
