Inhaltszusammenfassung zur Seite Nr. 1
Hardware Installation Guide for the
QLA22xx Board Family
Fibre Channel Host Adapter Boards for the PCI Bus
FC0151103-00 E
February 6, 2001
Inhaltszusammenfassung zur Seite Nr. 2
QLogic Corporation Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications described in this document for any of these products are for illustrative purposes only. QLogic Corporation makes no r
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents Section 1 Introduction 1.1 General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.2 What is Fibre Channel?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Section 2 Hardware Installation 2.1 Preinstallation Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 2.2 What You Need for Installation . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 4
Table of Contents QLA22xx Hardware Installation Guide FIGURES Figure Page 2-1 QLA2200 Board Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2-2 QLA2200F Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2-3 QLA2202F Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 2-4 QLA2204F Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 2-5 QLA2200G Board Layout . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 5
Section 1 Introduction NOTE: The following QLogic host adapter boards are collectively referred to as the QLA22xx board unless otherwise noted: QLA2200 family (64-bit PCI to Fibre Channel copper media): FC0210406-03 (ISP2200 chip) FC0210406-04 (ISP2200A/33 chip) FC0210406-05 (ISP2200A/66 chip) QLA2200F family (64-bit PCI to Fibre Channel optical media): FC0310406-03 (ISP2200 chip) FC0310406-04 (ISP2200A/33 chip) FC0310406-05 (ISP2200A/66 chip) QLA2202F family (64-bit PCI to dual cha
Inhaltszusammenfassung zur Seite Nr. 6
What is Fibre Channel? 1 – Introduction that support private loop direct attach (PLDA) and fabric loop attach (FLA). Installation of the QLA22xx board is quick and easy. 1.2 What is Fibre Channel? Fibre channel technology is outlined in the SCSI-3 Fibre Channel Protocol (SCSI-FCP) standard. Fibre Channel is a high-speed data transport technology used for mass storage and networking. It connects mainframes, super computers, workstations, storage devices, and servers. Fibre Channel supports da
Inhaltszusammenfassung zur Seite Nr. 7
Section 2 Hardware Installation 2.1 Preinstallation Procedures Before installing your QLA22xx board, take a moment to read this guide. CAUTION! The QLA22xx board contains parts that can be damaged by electrostatic discharge (ESD). Before handling the QLA22xx board, use standard methods to discharge static electricity. Keep the QLA22xx board in the antistatic bag until you are ready to install it. Place the board on the bag when you examine or configure it. Retain the bag for future us
Inhaltszusammenfassung zur Seite Nr. 8
ISP CHIP ISP CHIP What You Need for Installation 2 – Hardware Installation QLA22xx board in the unlikely event that the NVRAM is corrupted. If the NVRAM is corrupted, you will be prompted for the QLA22xx serial number. J1 SERIAL NUMBER Figure 2-1. QLA2200 Board Layout J1 SERIAL NUMBER Figure 2-2. QLA2200F Board Layout 2-2 FC0151103-00 E
Inhaltszusammenfassung zur Seite Nr. 9
SERIAL NUMBER ISP CHIP ISP CHIP 2 – Hardware Installation What You Need for Installation J1 J2 Figure 2-3. QLA2202F Board Layout FC0151103-00 E 2-3
Inhaltszusammenfassung zur Seite Nr. 10
SERIAL NUMBER J1 PORT 1 PORT 2 J2 J3 PORT 3 PORT 4 J4 What You Need for Installation 2 – Hardware Installation Figure 2-4. QLA2204F Board Layout 2-4 FC0151103-00 E ISP CHIP ISP CHIP ISP CHIP ISP CHIP
Inhaltszusammenfassung zur Seite Nr. 11
SERIAL NUMBER ISP CHIP ISP CHIP 2 – Hardware Installation What You Need for Installation J6 Figure 2-5. QLA2200G Board Layout J1 SERIAL NUMBER Figure 2-6. QLA2200L Board Layout FC0151103-00 E 2-5
Inhaltszusammenfassung zur Seite Nr. 12
ISP CHIP ISP CHIP Power Distribution 2 – Hardware Installation TX RX J3 J4 J1 SERIAL NUMBER J2 Figure 2-7. QLA2212F Board Layout 2.3 Power Distribution The QLA2200/2200L board supplies +5 volts to pin 7 of the HSSDC copper interface to support an external media interface adapter (MIA), if required. (An MIA converts copper bus signals to optical bus signals.) 2.4 Installation in the Computer Perform the following steps to install the QLA22xx board in your PC: 1. Check the motherboard and make a
Inhaltszusammenfassung zur Seite Nr. 13
2 – Hardware Installation Installation in the Computer 4. Choose any PCI bus slot that supports bus mastering. Most motherboards automatically assign an IRQ level and interrupt line; if your motherboard does not, you must assign the IRQ level and use interrupt line A for this slot. NOTE: ❑ Some motherboards have two kinds of PCI bus slots: master and slave. The QLA22xx board must be in a PCI bus master slot. (Some motherboards have PCI bus master slots that are shared with onboard devices.
Inhaltszusammenfassung zur Seite Nr. 14
Installation Help 2 – Hardware Installation 10. Power up all external FC devices, then power up the PC and observe the monitor. The BIOS is disabled by default. Consequently, the devices attached to the QLA22xx board are not identified. For example: QLogic Corporation QLA22xx PCI Fibre Channel ROM BIOS Version X.XX Copyright (C) QLogic Corporation 2000 All rights reserved. www.qlogic.com Press for Fast!UTIL BIOS for Adapter 0 is disabled ROM BIOS not installed NOTE: ❑ Sun SPARC systems
Inhaltszusammenfassung zur Seite Nr. 15
Section 3 Troubleshooting 3.1 Problems After Installation There are three basic types of installation problems that can cause your QLA22xx board to function incorrectly: hardware problems, system configuration problems, and Fibre Channel problems. The following section provides itemized checklists to help you determine why your QLA22xx board is not functioning. 3.2 Hardware Problem Checklist Are all of the circuit cards installed securely in the system? Are all of the cables secure
Inhaltszusammenfassung zur Seite Nr. 16
Fibre Channel Problem Checklist 3 – Troubleshooting 3.4 Fibre Channel Problem Checklist Were all of the FC devices powered up before you powered up the PC? Check that all cables are properly connected. 3-2 FC0151103-00 E
Inhaltszusammenfassung zur Seite Nr. 17
Appendix A Fast!UTIL NOTE: The Fast!Util BIOS utility does not run on Sun SPARC systems. Refer to the Software Installation Guide for the QLA2200 Board Family for information regarding adapter configuration settings. A.1 Introduction This appendix provides detailed configuration information for advanced users who want to customize the configuration of the QLA22xx board and the connected devices. The board can be configured using Fast!UTIL. Access Fast!UTIL by pressing - during the
Inhaltszusammenfassung zur Seite Nr. 18
Configuration Settings A – Fast!UTIL A.2.1 Host Adapter Settings From the Configuration Settings menu in Fast!UTIL, select Host Adapter Settings. The default settings for the QLA22xx host adapter board are listed in table A-1 and described in the following paragraphs. Table A-1. Host Adapter Settings Setting Options Default Host Adapter BIOS Enabled or Disabled Disabled Frame Size 512, 1024, 2048 1024 Loop Reset Delay 0-15 seconds 5 seconds Adapter Hard Loop ID Enabled or Disabled Disabled Ha
Inhaltszusammenfassung zur Seite Nr. 19
A – Fast!UTIL Configuration Settings A.2.3 Restore Default Settings The Restore Defaults option from the Configuration Settings menu restores the QLA22xx board default settings. A.2.4 Raw NVRAM Data This option displays the adapter’s NVRAM contents in hexadecimal format. This is a QLogic troubleshooting tool; you cannot modify the data. A.2.5 Advanced Adapter Settings From the Configuration Settings menu in Fast!UTIL, select Advanced Adapter Settings. The default settings for the QLA22xx host
Inhaltszusammenfassung zur Seite Nr. 20
Configuration Settings A – Fast!UTIL Execution Throttle. This setting specifies the maximum number of commands executing on any one port. When a port’s execution throttle is reached, no new commands are executed until the current command finishes executing. The valid options for this setting are 1-256. The default (optimum) is 16. Fast Command Posting. This setting decreases command execution time by minimizing the number of interrupts. The default is Enabled. >4GByte Addressing. This
