Inhaltszusammenfassung zur Seite Nr. 1
FO-DVI-XX-MM Series
User’s Guide
Models
FO-DVI-XX-MM
© 2008 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations
or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to
specifications and product descriptions at any time without notice. No license, whethe
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents Section 1: Getting Started ...................................................................................................................... 4 1.1 Important Safeguards ............................................................................................................ 4 1.2 Safety Instructions ................................................................................................................. 5 1.3 Regulatory Notices Federal Communications Commi
Inhaltszusammenfassung zur Seite Nr. 3
www.avenview.com 3
Inhaltszusammenfassung zur Seite Nr. 4
Section 1: Getting Started 1.1 Important Safeguards Please read all of these instructions carefully before you use the device. Save this manual for future reference. What the warranty does not cover Any product, on which the serial number has been defaced, modified or removed. Damage, deterioration or malfunction resulting from: Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions
Inhaltszusammenfassung zur Seite Nr. 5
1.2 Safety Instructions Do not dismantle the housing or modify the module. Dismantling the housing or modifying the module may result in electrical shock or burn. Refer all servicing to qualified service personnel. Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous voltage or other hazards Keep the module away from liquids. Spillage into the housing may result in fire, electrical shock, or equipment damage. If an obj
Inhaltszusammenfassung zur Seite Nr. 6
1.5 Model Description FO-DVI-XX-MM Model Name Length in Meters (5 = 5 meters, 10 = 10 meters) 1.6 Package Contents Before you start the installation of the converter, please check the package contents. - DVI Optical Cable with Receiver and Transmitter - User’s Manual 1.7 Before Installation Put the product in
Inhaltszusammenfassung zur Seite Nr. 7
1.8 Installation This product is composed of a Transmitter converting the graphic signal of a computer to optical and Optical Fiber propagating the optical signal and Receiver supplying electrical signal to monitor converted from the optical signal to electrical signal. The Transmitter should be connected to computer and the Receiver should be connected to a monitor (as shown below). Connection diagram of FO-DVI-XX-MM Avenview FO-DVI-xx-MM is designed to self detect the resolution
Inhaltszusammenfassung zur Seite Nr. 8
1.9 General Troubleshooting Problem Possible Solution Check if the PC Power is on Check if connection to the computer and the monitor are No Image correct. Turn the PC Power off and on again. This product supports up to UXGA resolution. Screen Defects Appear Check the DVI connection Check the maximum resolution range of the graphics card. www.avenview.com 8
Inhaltszusammenfassung zur Seite Nr. 9
Section 2: Specifications Item Description Video Bandwidth 1.65Gbps (Single Link) DVI 24Ping Plug Connector Power Consumption 5V / 0.5A (min) SXGA 1280 x 1024 @ 700 meters (2300 feet) Supported Resolution UXGA 1600 x 1200 @ 500 meters (1650 feet) and Distance WUXGA 1920 x 1200 @ 100 meters (330 feet) Optical Optical Source 850nm VCSEL O/E Converter PIN Photo Diode Fiber Type Multi-Mode Fiber Environmental Operation 0˚ to 50˚C Degree Storage -20˚ to 70˚C Degree 2.1 Part L
Inhaltszusammenfassung zur Seite Nr. 10
Item Description Q’t y Material A DVI-D Single Link 18 Plug 2 Glass filled thermoplastic UL94V-0 B DVI Case-Top, Bottom 2 Glass filled PC UL94V-0 C DVI Thumb Screw 4 SUM 24L+ABS D Stopper 2 PVC 55% E Epoxy Printed Circuit Board for Tx 1 FR-4, 1.5t UL94V-0 F Optical Connector for VCSEL,PD 2 PA46 UL94V-0 + C5210 G Optical Connector for fiber 2 PA46 UL94V-0 H Epoxy Printed Circuit Board for Rx 1 FR-4, 1.5t UL94V-0 I Vertical Surface Emitting Laser Diode 4 GaAs J Photo Detector 4 GaAs K
Inhaltszusammenfassung zur Seite Nr. 11
2.3 Signal Pin Assignment - Fully compatible with DVI Rev 1.0 standard - R, G, B and Clock signals are transmitted by optical fibers. - DDC, Hot plug detection signal and 5V power is transmitted by electrical copper wire. - External power is not required for operation Pin Signal Assignment Pin Signal Assignment Pin Signal Assignment 1 T.M.D.S. Data2- 9 T.M.D.S. Data1- 17 T.M.D.S. Data0- 2 T.M.D.S. Data2+ 10 T.M.D.S. Data1+ 18 T.M.D.S. Data0+ 3 T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shie
Inhaltszusammenfassung zur Seite Nr. 12
2.5 Characteristics of FO-DVI-XX Cable 2.5.1 Optical Fiber Construction and Characteristic The construction of the buffered optical fiber shall be in accordance with Figure 1 and Table 1 below: Item Description Fiber Type Hard Plastic Clad Silica Optical Fiber(H-PCF) Index Profile Semi Graded Material GeO doped Silica glass 2 Core Diameter 200±5um Non-circularity Less than 6% Material Fluoroacrylate Cladding Diameter 225±5um Concentricity Less than 6um error Material Ac
Inhaltszusammenfassung zur Seite Nr. 13
2.6 FO-DVI-XX Cable Construction The construction of 4 Optical Fibers and 4 Copper wires cable shall be in accordance with Figure and Table below: The Dimension of FO-DVI-XX-MM Cable Items Uni Specification t DVI Cable Make-up - Layer Stranding Drain Wires (Size/Stranded) mm(AWG) -0.203/7 (24) AL-Mylar Screen Shield - A helically Cable Outer Diameter mm 7.40±0.20 Jacket Color - FR-PVC(Orange) Cable Marking - If need www.avenview.com 13
Inhaltszusammenfassung zur Seite Nr. 14
2.7 Physical Interconnect Specification 2.7.1 Mechanical Characteristics Item Test Condition Requirements No discontinuity at 1us or longer (each ANSI/EIA-364-28, Condition III Method Vibration contact) when continuity is tested 5A, 15 minute/axis per ANSI/EIA-364-46 No discontinuity at 1us or longer (each ANSI/EIA-364-27 Condition A Mechanical Shock contact) when continuity is tested (specified pulse) per ANSI/EIA-364-46 Low Level contact resistance per ANSI/EIA-364-09 ANSI/E
Inhaltszusammenfassung zur Seite Nr. 15
2.7.2 Connector Electrical Characteristics Item Test Condition Requirements Contact Resistance ANSI/EIA-364-23 20mΩ, maximum, initial per contact mated pair 10mΩ, maximum change from original per contact mated pair Shell Resistance ANSI/EIA-364-06A-83 50mΩ, maximum initial Contact resistance measured from 50mΩ, maximum change from receptacle shell leg to plug cable original braid. Test current = 100mA; Test Voltage = 5V DC open circuit maximum Dielectric Withstanding Voltage ANSI/E
Inhaltszusammenfassung zur Seite Nr. 16
Disclaimer While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or conseque
Inhaltszusammenfassung zur Seite Nr. 17
regarding such products, including but not limited to, the implied warranties of merchantability, fitness for a particular purpose, and non-infringement. www.avenview.com 17
