Inhaltszusammenfassung zur Seite Nr. 1
BiPAC 7202 / 7202G
(802.11g) ADSL2+ Router
User’s Manual
Inhaltszusammenfassung zur Seite Nr. 2
Chapter 1 ................................................................................................. 1 1.1 Introducing the BiPAC 7202(G) ............................................. 1 1.2 Features................................................................................. 3 1.3 Applications of the BiPAC 7202(G) ........................................ 6 Chapter 2 ................................................................................................. 7 2.1 Important No
Inhaltszusammenfassung zur Seite Nr. 3
Chapter 1 Introduction 1.1 Introducing the BiPAC 7202(G) Thank you for purchasing the BiPAC 7202(G) ADSL Router by Billion. Your new router is an all-in-one unit that combines an ADSL modem, ADSL router and Ethernet network switch to provide everything you need to get the machines on your network connected to the Internet over an ADSL broadband connection. The BiPAC 7202(G) router complies with ADSL2+ standards for deployment worldwide and supports downstream rates of up to 24 Mbps and
Inhaltszusammenfassung zur Seite Nr. 4
addresses making them invisible to outside users on the Internet, so it is much more difficult for a hacker to target a machine on your network. Second, it can block and redirect certain ports to limit the services that outside users can access. To ensure that games and other Internet applications run properly, you can open specific ports for outside users to access internal services on your network. The Integrated DHCP (Dynamic Host Control Protocol) client and server services allow mu
Inhaltszusammenfassung zur Seite Nr. 5
1.2 Features Express Internet Access – ADSL2/2+ capable The BiPAC 7202(G) complies with ADSL worldwide standards. Supporting downstream rates of 8Mbps with ADSL, the router is capable of up to 12/24 Mbps with ADSL2/2+, and upstream rates of up to 1 Mbps. Users enjoy not only high-speed ADSL services but also broadband multimedia applications such as interactive gaming, video streaming and real-time audio which are easier and faster than ever. The router is compliant with Multi-Mode stand
Inhaltszusammenfassung zur Seite Nr. 6
Domain Name System Relay Domain Name System (DNS) relay provides an easy way to map a domain name with a user-friendly name such as www.billion.com with an IP address. When a local machine sets its DNS server to the router’s IP address, every DNS conversion request packet from the PC to this router is forwarded to the real DNS on the outside network. Dynamic Domain Name System (DDNS) The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname. This dynamic I
Inhaltszusammenfassung zur Seite Nr. 7
This feature filters the packet based on IP addresses as well as Port numbers. Filtering packets to and from the Internet provides a higher level of security control. Static and RIP1/2 Routing An easy static routing table or RIP1/2 routing protocol supports routing capability. Simple Network Management Protocol (SNMP) SNMP allows convenient remote management of the router. Web-based GUI A web-based GUI offers easy configuration and management. User-friendly and with on-line help, it a
Inhaltszusammenfassung zur Seite Nr. 8
1.3 Applications of the BiPAC 7202(G) 6
Inhaltszusammenfassung zur Seite Nr. 9
Chapter 2 Product Overview 2.1 Important Notes Do not use the BiPAC 7202(G) in high humidity or high temperatures. Do not use the same power source for the BiPAC 7202(G) as other equipment. Do not open or repair the case yourself. If the BiPAC 7202(G) is Warning too hot, turn off the power immediately and have it repaired at a qualified service center. Avoid using this product and all accessories outdoors. Place the BiPAC 7202(G) on a stable surface.
Inhaltszusammenfassung zur Seite Nr. 10
2.3 The Front LEDs BiPAC 7202 BiPAC 7202G LED Description 1 PPP : Steady glow when there is a PPPoA / PPPoE connection. Lights when successfully connected to an ADSL DSLAM 2 ADSL: (linesync). Steady glow when connected to an Ethernet device. LAN Port 3 Glows green for 100Mbps; Orange for 10Mbps. 1-4: Blinking light when data is Transmitted / Received. WLAN Lit green when the wireless connection is established. 4 (7202G Flashes when sending/receiving data. onl
Inhaltszusammenfassung zur Seite Nr. 11
2.4The Rear Ports BiPAC 7202 3 4 1 2 BiPAC 7202G 4 3 1 2 5 Port Description 1 PWR Connect the supplied power adapter to this jack. After the router is powered on, press this recessed button using the end of paper clip or other small pointed object to reset the router or to restore it to factory default settings. 1. Recovery procedures for non-working routers (e.g. after a failed firmware upgrade flash): Hold the Emergency/Failure Recovery Button on the back of the modem
Inhaltszusammenfassung zur Seite Nr. 12
password will be reset to admin, and the modem will be accessible via its default IP address at http://192.168.1.254/ Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the LAN 3 four LAN ports when connecting to a PC or an office/home network of 10Mbps or 100Mbps. ADSL Connect the supplied RJ-11 (telephone) cable to this port when 4 (LUNE) connecting to the ADSL/telephone network. Power 5 Power ON/OFF switch. Switch The detail instruction in Emergency/Failure Recovery Butt
Inhaltszusammenfassung zur Seite Nr. 13
2.5 Cabling One of the most common causes of problems is bad cabling or ADSL line(s). Make sure that all connected devices are turned on. On the front of the product is a bank of LEDs. Verify that the LAN Link and ADSL line LEDs are lit. If they are not, verify that you are using the proper cables. Ensure that all other devices connected to the same telephone line as your Billion router (e.g. telephones, fax machines, analog modems) have a line filter connected between them and the wall
Inhaltszusammenfassung zur Seite Nr. 14
Chapter 3 Installation You can configure the BiPAC 7202(G) router through the convenient and user-friendly interface of a web browser. Most popular operating systems such as Linux and Windows 98/NT/2000/XP/Me include a web browser as a standard application. 3.1 Before Configuration PCs must have a properly installed Ethernet interface and connect to the router directly or through an external repeater hub. In addition, PCs must have TCP/IP installed and configured to obtain an IP ad
Inhaltszusammenfassung zur Seite Nr. 15
Configuring a PC in Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. 13
Inhaltszusammenfassung zur Seite Nr. 16
Configuring a PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. 14
Inhaltszusammenfassung zur Seite Nr. 17
Configuring PC in Windows 98/Me 1.Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2.Select TCP/IP ->NE2000 Compatible, or the name of your Network Interface Card (NIC) in your PC. 3.Select the Obtain an IP address automatically radio button. 4.Then select the DNS Configuration tab. 5.Select the Disable DNS radio button and click OK to finish the configuration. 15
Inhaltszusammenfassung zur Seite Nr. 18
Configuring PC in Windows NT4.0 1.Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2.Select TCP/IP Protocol and click Properties. 3.Select the Obtain an IP address from a DHCP server radio button and click OK. 16
Inhaltszusammenfassung zur Seite Nr. 19
3.2 Factory Default Settings Before configuring the BiPAC 7202(G) router, you need to know the following default settings. Web Interface: Username: admin Password: admin LAN Device IP Settings: IP Address: 192.168.1.254 Subnet Mask: 255.255.255.0 ISP setting in WAN site: PPPoE DHCP Server: DHCP server is enabled. Start IP Address: 192.168.1.100 IP pool counts: 100 3.2.1 Username and Password The default username and password are “admin” and “admin” respectively.
Inhaltszusammenfassung zur Seite Nr. 20
3.3 LAN and WAN Port Addresses The parameters of LAN and WAN ports are preset at the factory. The default values are shown below. LAN Port WAN Port IP address 192.168.1.254 The PPPoE function is enabled to Subnet Mask 255.255.255.0 automatically get the WAN port DHCP server function Enabled configuration from the IP addresses for 100 IP addresses continuing from ISP, but you have to distribution to PCs 192.168.1.100 through set the username and 192.168.1.199 password first.
