Inhaltszusammenfassung zur Seite Nr. 1
ENHWI-G
IEEE 802.11g
Wireless Broadband Router
User Guide
Inhaltszusammenfassung zur Seite Nr. 2
Regulatory notes and statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions however are far much less than the electromagnetic energy emissions from wireless devices like for example mobile phones. Wireless LAN devices are safe for use frequency safety standards and recommendations. The use of Wireless LAN devices may be restricted in some situations or environments for exa
Inhaltszusammenfassung zur Seite Nr. 3
The radiated output power of this Wireless LAN device is far below the FCC radio frequency exposure limits. Nevertheless, this device shall be used in such a manner that the potential for human contact during normal operation is minimized. When nearby persons has to be kept to ensure RF exposure compliance, in order to comply with RF exposure limits established in the ANSI C95.1 standards, the distance between the antennas and the user should not be less than 20 cm. FCC Interference Statem
Inhaltszusammenfassung zur Seite Nr. 4
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Protection requirements for health and safety – Article 3.1a Testing for electric safety acco
Inhaltszusammenfassung zur Seite Nr. 5
Inhaltszusammenfassung zur Seite Nr. 6
2.2.1 Basic ...................................................................................................... 24 2.2.2 Authentication ....................................................................................... 25 2.2.3 Advanced............................................................................................... 27 2.3 Status............................................................................................................ 27 2.3.1 Device Information......
Inhaltszusammenfassung zur Seite Nr. 7
ABOUT THIS GUIDE Congratulations on your purchase of this IEEE 802.11g Wireless Broadband Router. This integrated access device combines Internet gateway functions with wireless LAN and Fast Ethernet switch. It provides a complete solution for Internet surfing and office resources sharing, and it is easy to configure and operate for every users. Purpose This manual discusses how to install the IEEE 802.11g Wireless Broadband Router. Overview of this User’s Guide Introduction. Describes
Inhaltszusammenfassung zur Seite Nr. 8
INTRODUCTION With the explosive growth of the Internet, accessing information and services at any time, day or night has become a standard requirement for most people. The era of the standalone PC is waning. Networking technology is moving out of the exclusive domain of corporations and into homes with at least two computers. This integrated access device combines Internet gateway functions with wireless LAN and Fast Ethernet switch. Designed for the business and home, it saves you the c
Inhaltszusammenfassung zur Seite Nr. 9
Features: High speed data transfer rate Supports NAT for share 1 IP address to all LAN user. Supports PPPoE and PPTP protocol for Dial-Up ADSL. Supports 64/128 bit WEP Encryption Supports WPA security Supports DHCP Server / Client. Supports UPnP (Universal Plug and Play). Supports virtual server mapping. Supports packet filtering. Supports DNS Simple Firewall protection. Upgradeable firmware for future function. Simple setting using Quick Setup. Easy configuration via
Inhaltszusammenfassung zur Seite Nr. 10
UNPACKING AND SETUP This chapter provides unpacking and setup information for the Wireless Broadband Router. Unpacking Open the box of the Wireless Broadband Router and carefully unpack it. The box should contain the following items: One Wireless Internet Broadband Router One external power adapter One CD-Rom with this User’s Guide If any item is found missing or damaged, please contact your local reseller for replacement. Setup The setup of the Wireless Broadband Router can be pe
Inhaltszusammenfassung zur Seite Nr. 11
HARDWARE INSTALLATION Front Panel The figure below shows the front panel of the Wireless Broadband Router. Wireless Broadband Router Front Panel POWER This indicator lights green when the hub is receives power, otherwise it is off. SYSTEM This indicator blinks green means the Internet Broadband Router is working successful. Otherwise, this indicator always on or off means the function of the Internet Broadband Router is fail. WAN (Link/ACT) The indicators light green when the WAN po
Inhaltszusammenfassung zur Seite Nr. 12
Antenna There are two 2 dBi Gain Antenna in the rear panel for wireless connection. LAN (1-4) Four RJ-45 10/100Mbps Auto-MDIX ports for connecting to either 10Mbps or 100Mbps Ethernet connections. WAN In the four port broadband router, there is an RJ-45 10/100Mbps Auto-MDIX port for the WAN that will fit the xDSL/Cable modem’s specification need. DC IN Plug the power adapter to this power jack RESET Use a pin-shape item to push to reset this device to factory default settings. It will
Inhaltszusammenfassung zur Seite Nr. 13
Connect the Router using Wireless LAN 1. Plug in one end of the RJ45 network cable to the xDSL/Cable Modem. 2. Plug in the other end of the RJ45 network cable to the Wireless Internet Broadband Router WAN port. Check the installation The control LEDs of the Wireless Internet Broadband Router are clearly visible and the status of the network link can be seen instantly: 1. With the power source on, once the device is connected to the broadband modem, the Power, CPU, LAN, WLAN and WAN po
Inhaltszusammenfassung zur Seite Nr. 14
PC NETWORK TCP/IP SETTING The network TCP/IP settings differ based on the computer’s operating system (Win95/98/ME/NT/2000/XP) and are as follows. Windows 95/98/ME 1. Click on the “Network neighborhood” icon found on the desktop. 2. Click the right mouse button and a context menu will be show. 3. Select “Properties” to enter the TCP/IP setting screen. 4. Select “Obtain an IP address automatically” on the “IP address” field. 5. Select “Disable DNS” in the “DNS” field. 8
Inhaltszusammenfassung zur Seite Nr. 15
6. Select “None” for the “Gateway address” field. Windows 2000 Double click on the “My computer” icon on the desktop. When “My computer” window opens, open the “Control panel” and then open the “Network dialup connection” applet. Double click on the “Local area network connection” icon. Select “Properties” to enter the TCP/IP setting window. 1. In the “Local area network status” window, click on “Properties.” 2. In the “Local area network connection” window, first select TCP/IP setting
Inhaltszusammenfassung zur Seite Nr. 16
Windows XP Point the cursor and click the right button on the “My Network Place” icon. Select “properties” to enter the TCP/IP setting window. 1. Set “IP address” to “Obtain an IP address automatically.” 2. Set “DNS” to “Obtain DNS server address automatically.” 10
Inhaltszusammenfassung zur Seite Nr. 17
WIRELESS BROADBAND ROUTER CONFIGURATION First make sure that the network connections are functioning normally. This Wireless Broadband Router can be configured using Internet Explorer 4.0 or newer web browser versions. Login to the Wireless Broadband Router through WLAN Before configuring the Wireless Broadband Router through WLAN, make sure that the SSID, Channel and the WEP is set properly. The default setting of the Wireless Broadband Router that you will use: SSID: default Channel:
Inhaltszusammenfassung zur Seite Nr. 18
Quick Setup Setup wizard is provided as the part of the web configuration utility. User can simply follow the step-by-step process to get the wireless router configuration ready to run in 6 easy steps by clicking on the “Wizard” button on the function menu. The following screen will appear. Please click “Next” to continue. Step 1: Set up new Password User can change the password and then click “Next” to continue. 12
Inhaltszusammenfassung zur Seite Nr. 19
Step 2: Choose time zone Select the time zone from the drop down list. Please click “Next” to continue. Step 3: Set LAN connection and DHCP server Set user’s IP address and mask. The default IP is 192.168.1.1. If user likes to enable DHCP, please click “Enabled”. DHCP enabled is able to automatically assign IP addresses. Please assign the range of IP addresses in the fields of “Range start” and “Range end”. Please click “Next” to continue. 13
Inhaltszusammenfassung zur Seite Nr. 20
Step 4: Set Internet connection Select how the router will set up the Internet connection: Obtained IP automatically; Fixed IP address; PPPoE to obtain IP automatically; PPPoE with a fixed IP address; PPTP. Obtain IP automatically (DHCP client): If user has enabled DHCP server, choose "Obtain IP automatically (DHCP client)" to have the router assign IP addresses automatically. Fixed IP Address: 14
