Inhaltszusammenfassung zur Seite Nr. 1
■ Contents
IEEE 802.11b Outdoor
CHAPTER 1. INTRODUCTION .................................................................. 1
1.1 INTRODUCING THE WIRELESS CLIENT BRIDGE........................................... 1
Wireless Client Bridge
1.2 PRODUCT FEATURES ................................................................................. 1
1.3 PACKAGE CONTENTS................................................................................. 1
1.4 SYSTEM REQUIREMENTS ...................
Inhaltszusammenfassung zur Seite Nr. 2
5.1 SYSTEM INFORMATION............................................................................ 38 5.2 STATISTIC INFORMATION ........................................................................ 39 Chapter 1. Introduction 5.3 SITE SURVEY........................................................................................... 40 5.4 WIRELESS LINK INFORMATION ............................................................... 41 1.1 Introducing the Wireless client bridge CHAPTER 6
Inhaltszusammenfassung zur Seite Nr. 3
1.4 System Requirements Chapter 2. Installation and Basic Configuration Installation of the Outdoor Wireless Client Bridge requires the following: This chapter describes the procedures of installing the Wireless client 1. A Windows-based PC/AT compatible computer or Ethernet bridge. data device with an available RJ-45 Ethernet port to run the configuration program or with TCP/IP connection to the Ethernet network. 2.1 Before You Start 2. A 10/100Base-T Ethernet RJ-45 Ethernet cable i
Inhaltszusammenfassung zur Seite Nr. 4
Data Input Port 3 for connecting cross-over Ethernet Cable to PC or straight Ethernet cable to Hub Switch Router. 2.2 Locate the Wireless client bridge and Inline 110~240VAC, 50~60Hz AC/DC power adapter DC Input Port Power Injector Ports 4 Power & Data Output Port 5 for connecting the 30m RJ-45 Interface on the Wireless client bridge Unit CAT-5 Ethernet Cable. Ethernet Port 1 for connecting the RJ-45 CAT-5 Ethernet Grounding Port 6. cable. RS-232 Console Port 2 f
Inhaltszusammenfassung zur Seite Nr. 5
2.3 Preparing Installation Before installing Wireless client bridge for the outdoor application in a hard- to-reach location, we recommend to configure and test all the devices first. For configuring the Wireless client bridge, please follow the quick steps below to power up the Wireless client bridge. Step 1: Console Port Connection Figure 2.2.1 Step 4 You can also mount the Wireless client bridge to the mast as shown in Figure 2.2.2. Step 5 Step 2 Step 3 Step 1 Atta
Inhaltszusammenfassung zur Seite Nr. 6
NOTE: This connection is required for setting up initial configuration 2.4 Basic Configuration information. After configuration is completed, the RS-232 null modem console cable shall be removed, and run a cross-over Ethernet cable from Data Input Port to PC, or a straight Ethernet 2.4.1 What you need to know cable to LAN connection, e.g. Hub. The Wireless client bridge can be configured into two operation roles, Step 5 Attach one straight Ethernet cable to the Power & Data Output i
Inhaltszusammenfassung zur Seite Nr. 7
Step 4 Reboot Wireless client bridge. 2.4.3 Login into the Web Interface Step 5 When the Wireless client bridge is powered up, the “Current Network Status” will be displayed as shown below. The Wireless client bridge supports access to the configuration system through the use of an HTTP Interface. Web Configuration Before configuring Wireless client bridge, user needs to know the IP Address assigned to the unit. When shipped from the factory, the IP Address 192.168.5.99 was
Inhaltszusammenfassung zur Seite Nr. 8
● Site Survey Step 3 Enter “root” in the User Name and the Password fields, and click ● Wireless Link Info OK to enter the web configuration user interface screen as shown below. ▽ Utility ● Software Upgrade ● Administration Move through the tree by clicking on an icon to expand or collapse the tree. The nodes on the tree represent web pages that allow viewing and modifying the parameters. 2.4.4 Set IP Address, Subnet Mask, Default Route IP Web Configuration
Inhaltszusammenfassung zur Seite Nr. 9
IP Use MAC Addr. You can choice Enable or Disable. If you choice Enable , it will set IP = 2.4.6 Change Supervisor Account & Password 10.X.X.X that used to last 3 MAC Address ID. For example : Enter the Utility > Administration page. The figure below shows the MAC Addr = 00:47:55:43:43:49 => IP = 10.67.67.73(43hex=67decimal) Utility/ Administration page. If you choice Disable you need setting Bridge IP Address Information. Bridge IP Address Use this setting to assign or
Inhaltszusammenfassung zur Seite Nr. 10
2.4.7 Upgrade the Firmware Setup your TFTP Server The Trivial File Transfer Protocol (TFTP) Server allows you to transfer files across a network. You can download the firmware files for Wireless client bridge upgrades. After the TFTP Server is installed, make sure you have the proper TFTP Server IP address, the proper Wireless client bridge firmware files, and the TFTP Server is operational. Update the Firmware using the TFTP method Step 1 Enter the Utility > Software Upgrad
Inhaltszusammenfassung zur Seite Nr. 11
shown below. Step 2 Press keystroke to reboot the Wireless client bridge. Press Step 4 Select “F -- upgrade Flash memory” and it will display upgrade key during the boot process, and it will display prompt items for selection as the figure shown below. character NetARM> as the figure shown in the next page. Step 5 Select “3: SOHO” and select “4: WEBIMG” to update the firmware files one by one. Step 3 Press “h” keystroke, it will display related commands as the figure
Inhaltszusammenfassung zur Seite Nr. 12
2.4.8 Back-up the Wireless client bridge’s Configuration Files After configuring Wireless client bridge, user can back-up the configuration files. User can upload the latest back-up files and recover the Wireless client bridge configuration to the settings specified in the back-up files. Downloading Configuration Files Just being the same with firmware upgrade procedures. After the prompt character NetARM> is displayed, select “S – Save image to file”, and then select “6: CONFIG”
Inhaltszusammenfassung zur Seite Nr. 13
Chapter 3. Network Topologies 3.1 Wireless Client Bridge-to-Central Wireless Bridge This chapter describes several main types of installations implemented by using the Outdoor Wireless System commonly. This is by no means intended to be an exhaustive list of all possible configurations, but rather shows examples of some of the more common implementations. The Wireless client bridge can only be configured into Wireless Client Router/Bridge to accomplish the broadband wireless point-to-po
Inhaltszusammenfassung zur Seite Nr. 14
3.2 Wireless Client Router-to-Central Wireless 3.3 Wireless Client Bridge-to-Central Wireless Bridge Router Step 1 Set the COU to perform a bridge (bridge IP address: Step 1 Set the COU to perform a Wireless Router (Wireless Interface IP: 192.168.2.1). 192.168.1.1, Ethernet Interface IP: 192.168.2.1). It is a must to enable NAT on Ethernet interface (default route: 192.168.2.254). Step 2 Set Wireless parameters on COU: Channel (1) and SSID (wireless). Step 2 Set Wireless parameters
Inhaltszusammenfassung zur Seite Nr. 15
The operator can also disable NAT behavior on COU and enable NAT behavior on ROU (enable NAT on Wireless Interface). In this case, any 3.4 Wireless Client Router-to-Central Wireless outgoing packets will transfer to 192.168.1.2. Router The operator can also enable NAT behavior on COU (enable NAT on Ethernet interface) and enable NAT behavior on ROU (enable NAT on Wireless Interface). Step 1 Set the COU to perform a Wireless Router (Wireless Interface IP: 192.168.1.1, Ethernet In
Inhaltszusammenfassung zur Seite Nr. 16
Chapter 4. Network Parameters 4.1 IP Configuration Wireless Client Bridge Step 1 Enter the IP Address manually into the Bridge IP Address field. Step 2 Use Bridge IP Address setting to assign or change the bridge’s IP address. Step 3 Click FINISH at the bottom of this page to complete the modification of IP address. 4.2 Configure SNMP Select the “/General Config/ TCP/IP/SNMP”, and the SNMP screen appears. The figure below shows the current SNMP community pool and
Inhaltszusammenfassung zur Seite Nr. 17
3. Click OK to refresh the current trap host pool. 4.2.2 Configure Trap Host Pool 4. To modify another trap host entry to the current trap host pool, repeat step 1 through step 3. The Trap Host Pool has five entries. 5. When you have modified all the entries preferred, click FINISH. 1. To modify a entry, click the select button beside the entry index number and click Modify . The configuration page appears as following figure. 2. Specify the Version, IP Address and Communi
Inhaltszusammenfassung zur Seite Nr. 18
Step 4 Click FINISH at the bottom of this page to complete the modification. 4.3 Configure Wireless related parameters The following gives more info about the parameters set in the Wireless LAN Step 1 Select “/General Config/Wireless” and the Wireless LAN information page to users. information page appears as the figure shown below. rts Threshold The setting determines the packet size, ranging from 0 to 2339 bytes, at which the bridge issues a request to send (RT
Inhaltszusammenfassung zur Seite Nr. 19
numbers 0 through 9 and the letters A through F. The 40-bit WEP keys can contain any combination of 10 of these characters; the 128-bit WEP 4.4 Utility keys can contain any combination of 26 of these characters. The letters are not case-sensitive. 4.4.1 Software Upgrade Step 1 Click Utility, select Software Upgrade page as the figure shown below, and then use TFTP to upgrade AP. In the Utility – Software Upgrade page, user must specify the TFTP server IP and select by which file to
Inhaltszusammenfassung zur Seite Nr. 20
4.4.2 Administration Chapter 5. Monitor Information Step 1 Click Utility, Administration. The following figure shows the User can find the system running status and other information on this Utility – Administration page. window. Click the Running Status link on the left window, use can choose which function that he wants to monitor. General System Information The following information can be found in this block. Product Model Host Name Software Versi
