Inhaltszusammenfassung zur Seite Nr. 1
FENCE CONTROL
WITH ADJUSTABLE SOLAR PANEL
Model 47454
ASSEMBLY AND OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
Distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
Sa
Inhaltszusammenfassung zur Seite Nr. 2
SPECIFICATIONS TABLE ITEM DESCRIPTION Input Voltage 8.7 VDC Output Voltage 8 KV +/- 1.5 KV Battery Type 6 Volt, DC, Lead Acid, 4.5 AH Range of Fence Control 3 to 5 Miles (Single Strand Wire) Solar Panel Type Angle Adjustable Solar Panel Size 4-1/4” x 3-3/4” Rated Wattage In Full Sunlight 1.3 Watts Overall Dimensions 7-1/4” x 6-7/8” x 5-3/8” Weight 3.65 Lbs. SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, assembly, op- erating, inspection, maintenance and clean
Inhaltszusammenfassung zur Seite Nr. 3
7. STAY ALERT. Watch what you are doing at all times. Use common sense. Do not use this product when you are tired or distracted from the job at hand. 8. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that it will operate properly and perform its intended function. Check for damaged parts and any other conditions that may affect the operation of this product. Replace or repair damaged or worn parts immediately. 9. REPLACEMENT PARTS AND ACCESSORIES: When servicing,
Inhaltszusammenfassung zur Seite Nr. 4
4. DO NOT CONNECT ANY OTHER DEVICE, SUCH AS A POULTRY OR CATTLE TRAINER, TO A FENCE THAT IS ALREADY CONNECTED TO THE FENCE CONTROL. Should lightening strike the fence, its damaging electrical force will be conducted to all other devices. 5. AVOID ACCIDENTAL ELECTRICAL SHOCK. Never install an electric fence below high voltage power plant transmission lines. Never touch or attempt to climb over a fence that is electrically charged. Never use more than one Fence Control on the same fence.
Inhaltszusammenfassung zur Seite Nr. 5
UNPACKING When unpacking, check to make sure all the parts shown on the Parts List on page 11 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. INSTALLATION INSTRUCTIONS NOTE: For additional references to the parts listed below, refer to the Assembly Diagram on page 11. To Mount The Fence Control On A Horizontal Or Vertical Surface: 1. CAUTION: Prior to mounting the Fence Control, make sure
Inhaltszusammenfassung zur Seite Nr. 6
3. Caution: Do not use an existing Ground Rod that is hooked up to other electrical systems or to a water pipe. (See Figure B.) MOUNTING HOLES MAIN BODY (#4) FIGURE A 4. The front side of the solar shock (with terminals and switch/key) should face the sun light. The solar panel should face towards south to expose the solar panel to the maximum possible sunlight. 5. Connect one end of an appropriate length of 12 Gauge Insulated Wire to the Ground Rod, using a Ground Clamp (not provided). (
Inhaltszusammenfassung zur Seite Nr. 7
To Connect The Fence Line To The Fence Control: 1. CAUTION: Prior to connecting the Fence Line to the Fence Control, make sure its Power Switch (part #5) is in the “OFF” position (the Switch Cover [#13] must be removed from the Power Switch when the Fence Control is not in operation). (See Figure C, and Assy. Diagram.) 2. Splice one end of an appropriate length of 12-1/2 Gauge Insulated Wire onto the Fence Line. (See Figure B.) 3. Connect the other end of the 12-1/2 Gauge Insulated Wire t
Inhaltszusammenfassung zur Seite Nr. 8
NOTE: After making sure that all safety warnings and precautions (pages 2-4) are adhered to, the Fence Control is ready to be turned ON. 2. When the Battery (part #10) is fully charged, place the Switch Cover (#13) on the Power Switch (#5) and turn the Power Switch (part #5) to its “ON” position. (See Figure C, and Assy. Diagram.) 3. Observe the Indicating Lamp (part #7). A blinking Indicating Lamp shows that the electrical output is working properly. The fence is now electrically activa
Inhaltszusammenfassung zur Seite Nr. 9
Splices: 1. Two types of splicing may be used; hand splicing, or the use of specially designed splicing bolts and connectors. Gates: 1. A simple gate can be constructed from a single “hot” wire line with the use of an insulated gate handle. However, disconnecting the gate handle also disconnects the electric flow in the fence. A typical gate can be used without interfering with the electric flow in the fence by running an insulated wire under the gate, beneath the ground level. A “hot”
Inhaltszusammenfassung zur Seite Nr. 10
5. TROUBLESHOOTING: If the fence is not operating properly, make sure nothing, other than the fence posts, is touching the fence. Make sure all connections to the Fence Control are clean and tightened securely. Ensure that all fence wires and the ground wire connections are tightened securely. If necessary, use a commercial electric fence tester to check the output on the fence line. 6. TO CLEAN: wipe the outer body of the Fence Control with a soft, damp cloth, using a mild detergent. A
Inhaltszusammenfassung zur Seite Nr. 11
PARTS LIST / ASSEMBLY DIAGRAM 13 Switch Cover 1 13 NOTE: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. SKU 47454 PAGE 11
