Bedienungsanleitung Kohler Waterlite showerhead 8022A

Inhaltszusammenfassung zur Seite Nr. 1

Watertile Showerhead
Installation and User Guide
MODEL NUMBERS
8022A, 8023A
Important! Please quote the above model number(s) when ordering spares
IMPORTANT
INSTALLER: THIS MANUAL IS THE PROPERTY OF THE
CUSTOMER AND MUST BE RETAINED WITH THE PRODUCT
FOR MAINTENANCE AND OPERATIONAL PURPOSES.
1063864-AN2-E 17/02/12
1

Inhaltszusammenfassung zur Seite Nr. 2

10 121 BEFORE YOU BEGIN All information is based on the latest product information available at the time of publication. Kohler Co. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. Please leave these instructions for the consumer. NOTES: 1. Flush the water supply pipes thoroughly to remove any debris. 2. An in line water filter must be used with this product. 3. Inspect the supply pipes for damage. Replace as necessary. 4. O

Inhaltszusammenfassung zur Seite Nr. 3

INSTALLATION Before you Begin 1. Turn off the water supply. 2. Make sure that the Watertile showerhead is installed by a competent installer. 3. Before installation carefully inspect the new fixture for any signs of damage. 4. Kohler Co. reserves the right to make revisions in the design of products without notice. Install the Pipe and Elbow Finished Wall G ½” Elbow 1. Install the water supply pipes. 2. Install the wall mount elbow to the end of the water supply pipe at the shower Nipple head

Inhaltszusammenfassung zur Seite Nr. 4

Install the Watertile Showerhead Apply Silicone Sealant Prepare the Housing: 1. Position the housing so that the back of the leak shield is facing you. 2. Apply a bead of silicone sealant in the groove around the outside of the housing. Do not apply silicone sealant in or near the weep hole. 3. Allow the silicone sealant to cure. Weep Hole Install the Components: Finished Wall 1. Position the housing with the sealant side towards the finished wall and the narrow end of the housing facing

Inhaltszusammenfassung zur Seite Nr. 5

Finish the Installation 1. With the ribs of the sprayhead facing up, attach the sprayhead to the waterway. Waterway 2. Using a 3/16” hexagonal key, secure the sprayhead to the waterway with the Sprayhead 2 securing screws (supplied). Do not Hex Screws overtighten. 3. Check the sprayhead for upward and Ribs downward movement and that it sits Groove squarely within the housing. 4. Place the nozzle membrane over the Nozzle Membrane sprayhead Note! For optimum performance make sure that the

Inhaltszusammenfassung zur Seite Nr. 6

SPARE PARTS 1079599 Grommet 1036043 Shield 1056030 Elbow 1055233 1043560** Adapter Housing 1045773 Base (includes clamps) 1036044 Clamp 1048768 Sprayhead 1039746 1036044 Nozzle Clamp 1036041** 1041575 Spray Face Nozzle 1041573** 1045769 Spray Face Sprayhead ** Finish/colour code must be specified when ordering. 1063864-AN2-E 17/02/12 6

Inhaltszusammenfassung zur Seite Nr. 7

CARE AND CLEANING Like anything of lasting quality, Kohler tapware and fittings require a certain amount of periodic care to preserve their lustrous finish. Clean your new Kohler tapware and fittings with a mild soap, rinse thoroughly with warm water and dry with a clean, soft cloth. The ideal cleaning technique is to always blot dry any water from metal surfaces. Allowing water to evaporate on metal will form water deposits. It is important to use a dabbing action to dry metal, not an abras