Bedienungsanleitung JBL P-Kit

Inhaltszusammenfassung zur Seite Nr. 1

P-Series Owner's Manual 5/25/99 9:46 AM Page 1
Automotive Loudspeakers
P-432, P-532, P-632, P-9632, P-9633,
P-332, P-6432, P-7532, P-23t & P-Kit Owner’s Manual
GENUINE JBL

Inhaltszusammenfassung zur Seite Nr. 2

P-Series Owner's Manual 5/25/99 9:46 AM Page 2 Installation Warnings and Tips Caution: In some cars, fuel tanks may be Warning: Playing loud music in an auto- Thank you for purchasing JBL's Power • Always wear protective eyewear when located directly beneath the rear deck. mobile can permanently damage your Series™ automotive loudspeakers. In using tools. Check for adequate speaker-basket hearing as well as hinder your ability to order that we may better serve you • Turn off all audio systems

Inhaltszusammenfassung zur Seite Nr. 3

P-Series Owner's Manual 5/25/99 9:46 AM Page 3 Installation of the P-332, P-6432 and P-7532, as shown in Figure 1. Installation of the P-432, P-532, P-9632 and P-9633, as shown in Figures 2 and 3. Figure 1. Figure 2. Figure 3. Note: The P-332, P-6432 and P-7532 are designed as Note: If you are mounting the P-532, P-9632 or P-9633 Note: Some installations may require some or all direct replacements for original-equipment speakers behind factory grilles, omit the grille and grille tray in of t

Inhaltszusammenfassung zur Seite Nr. 4

P-Series Owner's Manual 5/25/99 9:46 AM Page 4 Installation of the P-632, as shown in Figures 4a and 4b. The P-632 uses JBL's Intermount III™ mounting system. Intermount III™ provides for easy installation of these speakers in many standard and nonstandard locations that will accommodate a 6-1/2" speaker. Figure 4a. Figure 4b. Using Intermount III™ in American and Japanese cars with Using Intermount III™ in European and American 165mm openings for 6-1/2" speakers. openings or custom-mountin

Inhaltszusammenfassung zur Seite Nr. 5

P-Series Owner's Manual 5/25/99 9:46 AM Page 5 Converting the P-432, P-532 and P-632 to a component system using the optional P-Kit (sold separately), as shown on pages 5 and 6. Separating the tweeter and woofer, as shown in Figures 5a and 5b. Figure 5a. Figure 5b. Remove the orange wire cover by inserting a small Detach the tweeter by turning it counterclockwise to screwdriver into the notch between the two terminals and unlock it, then pull it away from the woofer while feeding prying upwa

Inhaltszusammenfassung zur Seite Nr. 6

P-Series Owner's Manual 5/25/99 9:46 AM Page 6 Mounting the tweeter (P-23t), as shown in Figures 6a Connecting the woofer and tweeter to the and 6b. The tweeter may be either surface-mounted or passive crossover, as shown in Figures 7a and 7b. flush-mounted with parts supplied in the P-Kit. Figure 7a. Figure 6a. Figure 7b. Position the "Lo Pass" and "Twt Frq" according to the speaker you are using as shown in the callouts in Figure 7b. Surface-mounting the P-23t. Jumper Functions Lo Pass (

Inhaltszusammenfassung zur Seite Nr. 7

P-Series Owner's Manual 5/25/99 9:46 AM Page 7 Specifications P-432 P-532 P-632 P-9632 P-9633 4" 2-Way or 5-1/4" 2-Way or 6-1/2" 2-Way or 6" x 9" 2-Way 6" x 9" 3-Way Component System Component System Component System Component System Component System with Optional P-Kit with Optional P-Kit with Optional P-Kit Woofer-Cone Material Thermalum™ Thermalum™ Thermalum™ Thermalum™ Thermalum™ Tweeter-Diaphragm Material NeoGlass™ NeoGlass™ NeoGlass™ NeoGlass™ NeoGlass™ Frequency Response 65Hz – 22kHz 5

Inhaltszusammenfassung zur Seite Nr. 8

P-Series Owner's Manual 5/25/99 9:46 AM Page 8 Declaration of Conformity We, JBL Europe A/S Kongevejen 194B DK-3460 Birkerød DENMARK declare in own responsibility, that the products described in this owner’s manual are in compliance with technical standards: EN 50081-1:1992 EN 50082-1:1992 Steen Michaelsen JBL Europe A/S Birkerød. DENMARK. 3/99 JBL Consumer Products, 250 Crossways Park Drive, Woodbury, NY 11797 800-336-4JBL (4525) www.jbl.com Part No. POWSPKRSOM Made in China