Bedienungsanleitung JBL SCS500.5

Inhaltszusammenfassung zur Seite Nr. 1

SPECIFICATIONS
SUBWOOFER
SCS500.5 SYSTEM
Amplifier 150 Watts RMS
Frequency Response
Frequency Response 30Hz – 120Hz (–6dB)
30Hz – 20kHz (–6dB)
Woofer 10" (250mm)
Enclosure Bass-reflex
SATELLITES
Dimensions (H x W x D) (including feet)
Maximum Recommended Amplifier Power
20" x 13-3/4" x 15-3/4"
100 Watts
(508mm x 349mm x 400mm)
Nominal Impedance 8 Ohms
Weight 35 lb (15.9kg)
Sensitivity 88dB @ 1 Watt/1 meter
Frequency Response 100Hz – 20kHz (–6dB)
Tweeter
1/2" (13mm) Titanium-laminate dome,
vi

Inhaltszusammenfassung zur Seite Nr. 2

THANK YOU FOR CHOOSING JBL IMPORTANT SAFETY INSTRUCTIONS For more than 60 years, JBL provide every note of enjoy- Web site at www.jbl.com. has been involved in every ment that you expected – It enables us to keep you 1. Read these instructions. such as power supply cord or plug is dam- aspect of music and film and that when you think posted on our latest advance- 2. Keep these instructions. aged, liquid has been spilled or objects have recording and reproduction, about purchasing additional men

Inhaltszusammenfassung zur Seite Nr. 3

SPEAKER PLACEMENT MOUNTING OPTIONS FRONT CENTER CHANNEL SATELLITES AND SURROUNDS SPEAKERS SPEAKER SUBWOOFER 0–2 ft (0–0.6m) On shelves. On the wall. Wall On optional stands. brackets are included. SURROUND SPEAKERS ATTACHING THE SHELF STAND TO THE SPEAKER Prepare the speaker wire as the left, and the negative stand onto the back of the described on page 7. Thread conductor through the hole speaker in two places, as 5–6 ft the two conductors through on the right, looking at the shown. The shelf

Inhaltszusammenfassung zur Seite Nr. 4

+ + – – Gently pull the slack out of the screw in the lower screw hole. the bottom of the floor stand Make sure that all four Step 8: Hand-tighten the listening position at about wire and screw the adapter adapter to secure the speaker screws are driven into the Molded Nut™ while posi- ear-level height. In systems Screw the floor stand adapter onto the back of the speaker to the stand. stud and not into drywall. tioning the speaker for the where only analog surround into the floor stand’s thread

Inhaltszusammenfassung zur Seite Nr. 5

® ® DOLBY DIGITAL OR DTS DOLBY PRO LOGIC (NON-DIGITAL) – SPEAKER LEVEL (OR OTHER DIGITAL SURROUND MODE) CONNECTION Use this installation method Frequency Effects channel. your receiver for 5.1-channel RECEIVER SUBWOOFER for Dolby Pro Logic applica- Connect this jack to the LFE operation, as appropriate. tions (not Dolby Digital, DTS L output or subwoofer output The front left, front right, LINE or other digital processing), LFE LFE OUT LEVEL on your receiver or amplifier. center and surround

Inhaltszusammenfassung zur Seite Nr. 6

OPERATION TROUBLESHOOTING Move the Master Power switch If you will be away from home If there is no sound from any owner’s manual for that electrical outlet, and is of the speakers: product for further informa- turned on (Power switch (marked “Power” å) to the “•” for an extended period of time, tion. If the problem has fol- å in the “ ” position). (On) position to use the sub- or if the subwoofer will not be • Check that receiver/ampli- • lowed the speaker, consult woofer. The SUB500 subwoofer