Inhaltszusammenfassung zur Seite Nr. 1
MODEL 6720D
MODEL 6720DW
With Quick Charger
INSTRUCTION MANUAL
SPEC I FI CAT ION S
Model 6720D
Capdcities
No load speed Dimensions
IRPMi (Length x Didmeter) weiyht
Wood screw
~~
4 1 riim x 20 mm 5 rrim 209 mm x 42 mm 0 4 ky
150
15t32" x 3)4"1 11 3r64"l (8 1/4" x 1 5/8"1 10 9 lbsi
II1(1Ut 0Utl)"f Charging time
A C only 50 Hr 60 Hr DC24V 3 Hr
I I
* Manufacturer reserves the right to change specifications without notice.
* Note: Specifications may differ from country to country.
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO OF FIRE, ELECTRIC SHOCK, AND PER- REDUCE THE RISK SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence
Inhaltszusammenfassung zur Seite Nr. 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are t
Inhaltszusammenfassung zur Seite Nr. 4
I M PO RTAN T SAFETY INSTRUCTIONS I. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) product using battery. 3. CAUTION - To reduce risk of injury, charge only MAKITA type recharge- able batteries. Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger to rain or snow. 5. Use of
Inhaltszusammenfassung zur Seite Nr. 5
ADDITIONAL SAFETY RULES FOR CHARGER AND TOOL 1. The Charger and the tool are specifically designed to work together. Do not attempt to charge any other cordless tool with this Charger. Do not attempt to charge the tool with any other charger. 2. Do not charge the tool when temperature is BELOW 10°C (5OOF) or ABOVE 45OC (113OF). 3. Do not use charger in damp or wet locations. 4. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 5. Do not store the
Inhaltszusammenfassung zur Seite Nr. 6
Charging Connect the charging plug to the charging connector, then plug in the charger to the power receptacle. Charging takes 3 hours. CAUTION : 0The battery in your new tool is not fully charged. You will need to charge it before use. 0 Do not operate the tool during charging. 0 Overcharging more than 2 days considerably shortens the battery service life. Always unplug the charger after completing the charge. When you charge a new tool or a tool which has not been used for a long peri
Inhaltszusammenfassung zur Seite Nr. 7
Reversing switch action This tool has a reversing switch to change Reversing the direction of rotation. Move the revers- switch lever ing switch lever to the right for clockwise rotation or to the left for counterclock- Counter- wise. clockwise CAUTION : 0 Always check the direction of rotation before operation. 0Use the reversing switch only when the tool comes to a complete stop. Changing the direction of rotation before the tool stops may ruin the tool. Operation Place the poin
Inhaltszusammenfassung zur Seite Nr. 8
Manual driving operation This tool can be used as a manual screwdriver when the switch is in the off position. Be sure to keep your finger off the switch when performing manual driving operation CAUTION: When performing manual driving operation, do not insert a screwdriver, etc. into the hole in the end of the tool to increase torque on the screw. This may cause tool damage. Fastenings Application Dimensions of screw Workpiece 3.1 mm x 20 mm 220 screws (1 /8” x 3/4”) Lauan wood Wo
Inhaltszusammenfassung zur Seite Nr. 9
ACCESSOR I ES CAUTION : These . accessories -.. ..~ . or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Quick charger (A.C. only) 0 Bits Model DC2000 I Size I Part NO. Ph 11 lips #++F 1 784214-0A Slotted 784010-OA 9
Inhaltszusammenfassung zur Seite Nr. 10
Sep--16-'87 EN CORDLESS SCREWDRIVER Model 6720D Note: The switch and other part configurations may differ from country to country. 10
Inhaltszusammenfassung zur Seite Nr. 11
MODEL 6720D Sep-16 '87 EN ITEM NO. $fD DESCRIPTION DESCRIPTION NO. USE0 11 Steel Ball 2 4 14 1 Motor 21 Leaf Spring 15 1 Change Knob SwWh Lever 31 Plane Bearing 10 16 1 41 Retaining Ring S 10 17 1 Housinq Set [With Item 241 51 Flat Washer 10 18 1 Stopper Guide 61 Thrust Ball Bearing 1018 19 I stopper 71 Flat Washer 10 20 1 Compresslo" spmg 4 81 Spindle 21 1 Switch 93 Spur Gear 25 22 1 Circuit Board 1 10 Spur Gear 9 23 1 Bette," 11 3 Spur Gear 25 24 1 Housing Set [With Item 171
Inhaltszusammenfassung zur Seite Nr. 12
P Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. N i-Cd To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location. Call your nearest Makita Service Center or Distributor to determ
