Inhaltszusammenfassung zur Seite Nr. 1
Drywall Screwdriver
MODEL 6821
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Inhaltszusammenfassung zur Seite Nr. 2
SPECIFICATIONS Model 6821 Self drilling screw 6 mm (1/4”) Capacities Drywall screw 5 mm (3/16”) Bit shank size 1/4” Hex No load speed (RPM) 0 - 4,000/min. Overall length 273 mm (10 - 3/4”) Net weight 1.3 kg (2.9 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in
Inhaltszusammenfassung zur Seite Nr. 3
change the plug in any way. Double insula- 13. Do not overreach. Keep proper footing and balance at all times. Proper footing and tion eliminates the need for the three wire balance enables better control of the tool in grounded power cord and grounded power unexpected situations. supply system. 14. Use safety equipment. Always wear eye 5. Avoid body contact with grounded sur- protection. Dust mask, non-skid safety faces such as pipes, radiators, ranges and shoes, hard hat, or hearing protectio
Inhaltszusammenfassung zur Seite Nr. 4
model. Accessories that may be suitable tenance performed by unqualified personnel for one tool, may become hazardous when could result in a risk of injury. used on another tool. 24. When servicing a tool, use only identical replacement parts. Follow instructions in SERVICE the Maintenance section of this manual. 23. Tool service must be performed only by Use of unauthorized parts or failure to follow qualified repair personnel. Service or main- Maintenance instructions may create a risk of elec
Inhaltszusammenfassung zur Seite Nr. 5
SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. 5
Inhaltszusammenfassung zur Seite Nr. 6
FUNCTIONAL CAUTION: DESCRIPTION Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 002611 Depth adjustment A The depth can be adjusted by turning the locking sleeve. Turn it in “A” direction for less depth and in “B” direction for more depth. One full turn of the locking sleeve equals 2 mm (3/32”) change in depth. B 1 2 1. Locator 2. Locking sleeve 002617 Adjust the locking sleeve so that the tip of the locator is flush with the base
Inhaltszusammenfassung zur Seite Nr. 7
To stop the tool from the locked position, pull the switch trig- ger fully, then release it. 002634 Reversing switch action 1 A This tool has a reversing switch to change the direction of rotation. Move the reversing switch lever to the position (A side) for clockwise rotation or the position (B side) for counterclockwise rotation. B CAUTION: Always check the direction of rotation before operation. 1. Reversing switch lever Use the reversing switch only after the tool comes to a complete sto
Inhaltszusammenfassung zur Seite Nr. 8
OPERATION 002672 Fit the screw on the point of the bit and place the point of the screw on the surface of the workpiece to be fastened. Apply pressure to the tool and start it. Withdraw the tool as soon as the clutch cuts in. Then release the switch trigger. CAUTION: When fitting the screw onto the point of the bit, be careful not to push in on the screw. If the screw is pushed in, the clutch will engage and the screw will rotate suddenly. This could damage a workpiece or cause an injury. Ma
Inhaltszusammenfassung zur Seite Nr. 9
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 9 Cut
Inhaltszusammenfassung zur Seite Nr. 10
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
Inhaltszusammenfassung zur Seite Nr. 11
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA FLORIDA MISSOURI PENNSYLVANIA 3707 E. Broadway Rd., Ste. 6 750 East Sample Road 9876 Watson Road 1704 Babcock Blvd. Phoenix, AZ 85040 Pompano Beach, FL 33064 St. Louis, MO 63126-2221 Pittsburgh, PA 15209 (602) 437-2850 (954) 781-6333 (314) 909-9889 (412) 822-7370 CALIFORNIA GEORGIA NEBRASKA PUERTO RICO 41850 Christy St. 4680 River Green Parkway NW 4129 S. 84th St. 200 Guayama St. Fremont, CA 94538-5107 Duluth,
Inhaltszusammenfassung zur Seite Nr. 12
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
