Inhaltszusammenfassung zur Seite Nr. 1
Operator's Manual
SRP-500
Samsung Elector-Mechanics
Printed In Korea
2003. 2
Inhaltszusammenfassung zur Seite Nr. 2
Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. WARNING WARNING Violating following instructions can cause slight wound or damage the appliance. Violating following instructions can cause serious injury or death. Keep the desiccant out of children’s Install the printer on the stable surface. Do not plug several products in one You must use only the supplied adapter. If the
Inhaltszusammenfassung zur Seite Nr. 3
All rights reserved. No part of this publication may reproduced, stored in a EMC and Safety standards Applied retrieval, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Product Name : SRP-500 SAMSUNG ELECTRO-MECHANICS. The following standards are applied only to the printers that are so labeled. No patent liability is assumed with respect to the use of the information contained her
Inhaltszusammenfassung zur Seite Nr. 4
Table of contents • Chapter 3. DIP switch • Introduction …………………………………………………………….. 1 3-1 Setting the DIP switches …………………………….….…........ 18 3-2 Changing the DIP switch setting ……………………………… 20 • Chapter 1. Setting up the printer 1-1. Unpacking ……………………………….………..…………… 3 • Chapter 4. Code table …………………………………………………. 21 1-2. Choosing a place for the printer ………………………..…… 4 1-3. Connecting the cables ………………………………..……… 5 1-4. Installing or rep
Inhaltszusammenfassung zur Seite Nr. 5
Introduction The SRP-500 is a high-quality inkjet POS printer. This one-station printer has the following features. • Front view • Compact design and light-weight. • High-speed printing using logic-seeking. • Easy to use : clamshell mechanism. • High reliability and long life due to the use of stepping motors for both carriage return and paper feeding. • Two color printing (red/black/blue/green) available. • Various formats are possible because the paper feeding pitch i
Inhaltszusammenfassung zur Seite Nr. 6
Chapter 1 Setting up the printer 1-2. Choosing a place for the printer • Avoid locations that are subject to direct sunlight or excessive heat. 1-1. Unpacking • Avoid using or storing the printer in a place subject to excessive temperature or moisture. Your printer box should include the items shown in the illustration below. • Do not use or store the printer in a dirty location. If any items are damaged or missing, please contact your dealer. • When setting up the printer
Inhaltszusammenfassung zur Seite Nr. 7
• Connecting the interface cable 1-3. Connecting the cables Connect the printer to the host ECR (host computer) though an interface • Plugging in AC adapter cable matching the specification of the printer and the host ECR (host computer). Be sure to use a drawer that matches the printer’s specification. CAUTION • Before connecting the printer to the power supply, make sure that the Depending on the interface your system uses, either connect the serial, voltage and power sp
Inhaltszusammenfassung zur Seite Nr. 8
1-4. Installing or replacing paper roll 3) Remove the used CAUTION paper roll core if there is one. Notice the caution label and do not touch the auto cutter blade when 4) Insert the paper roll you open rear cover. as shown. 1) To prevent data loss, make sure that the printer is not receiving data. 2) Open the rear cover by pressing the open button and push the arrow mark back. 5) Be sure to note the correct direction that the paper should come off th
Inhaltszusammenfassung zur Seite Nr. 9
5) Take out old ink 1-5. Installing new Ink cartridge(s) cartridge(s). Place new cartridge(s) 1) Remove new ink cartridge from into carriage. sealed pouch. Hold plastic tab to ensure (Hold cartridge by round plastic clean installation. tab to avoid contamination) Black cartridge goes into the left carriage. The color cartridge goes into right carriage. (tab faces front of printer.) 2) Remove Mylar from face of new cartridge. CAUTION Do not touch ink cart
Inhaltszusammenfassung zur Seite Nr. 10
1-6. Using the control panel Most of the functions of this printer are governed by software, but you can monitor the printer’s status by looking at the lights on the Error (LED) control panel and for some procedures you will use the buttons. When this indicator light is on(but not blinking), it means that the printer is out of paper or almost out of paper or the printer covers are open. When this light blinking, there is an error. If you see this light blinking, turn off Co
Inhaltszusammenfassung zur Seite Nr. 11
Chapter 2 Troubleshooting 1-7. Self test The self test lets you know if your printer is operating properly. This chapter gives solutions to some printer problems you may have. It checks the control circuits, printer mechanisms, print quality, ROM version, and DIP switch settings. 2-1. The printer does not start printing. The test is independent of any other equipment or software, so it is a good idea to run it when you first set up the printer or if you have any trouble. I
Inhaltszusammenfassung zur Seite Nr. 12
2-2. The printer stops printing. 2-4. Printing is poor Obstructed ink nozzles in the print head will lower the print quality. • If the Error light is on (but not blinking), the printer is off line. Check to see that the covers are closed and check the paper state. Try cleaning the print head as described below: See Chapter 1 for instructions on installing or replacing the paper roll. • Cleaning the print head • If the Error light is blinking, there is an error. In this case, turn of
Inhaltszusammenfassung zur Seite Nr. 13
Chapter 3 DIP switch settings 2-5. You want to check a software program. Although the factory settings are best for almost all users, if you have special • Hexadecimal Dump requirements, you can change the DIP switch. This feature allows experienced users to see exactly what data is coming to the printer. This can be useful in finding software problems. When you turn on the hexadecimal dump function, the printer prints all commands 3-1. Setting the DIP switches and other dat
Inhaltszusammenfassung zur Seite Nr. 14
Transmission 2-7 2-8 2400 baud ON ON 4800 baud OFF ON 3-2. Changing the DIP switch setting 9600 baud OFF OFF 19200 baud ON OFF If you need to change settings, follow the steps below to make your changes. *1) : It may use in dark area. (like a restaurant). But printing speed to be slow down. *2) : Enalbe = Automatically print NV bit image #1 after cutting. *3) : EPSON Kitchen Printer mode : A alarm is generated by printer after auto-cutting CAUTION and in paper-end
Inhaltszusammenfassung zur Seite Nr. 15
Chapter 4 Code table The following page show the character code tables. To find the character corresponding to a hexadecimal number, count across the top of the table for the left digit and count down the left column of the table for the right digit. For example, 4A=J Page 2 (PC850 : Multilingual) Page 0 (PC437 : USA, Standard Europe) (International Character Set : USA) 21 22
Inhaltszusammenfassung zur Seite Nr. 16
Page 3 (PC860 : Portuguese) Page 4 (PC 863 : Canadian - French) 23 24
Inhaltszusammenfassung zur Seite Nr. 17
Page 5 (PC 865 : Nordic) page 16 (CP1252 : WinLatin1) 25 26
Inhaltszusammenfassung zur Seite Nr. 18
page 17 (PC 866 : Russian) page 18 (CP 852 : DosLatin2) 27 28
Inhaltszusammenfassung zur Seite Nr. 19
Page 19 (PC 858 : Euro) Page 21 (MS-DOS 862 : Israel) 29 30
Inhaltszusammenfassung zur Seite Nr. 20
Page 23 (MS-DOS 874 :Thai) Page 22 (MS-DOS 864 : Arabic) 31 32
