Inhaltszusammenfassung zur Seite Nr. 1
Xerox Wide Format 721P
Printer
Operator Manual
701P39415 April 2003
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
TABLE of CONTENTS Table of contents Safety Notes ............................................................................................................................................................. v EMC Notices ............................................................................................................................................... vii Australia/New Zealand..............................................................................................................
Inhaltszusammenfassung zur Seite Nr. 4
TABLE of CONTENTS 7. User Modes................................................................................................................................................49 User Mode 1 (Test Print) U1 ..............................................................................................................49 User Mode 2 (Date and Time setting) U2...........................................................................................51 User Mode 3 (Low Power Saver Mode) U3 .....
Inhaltszusammenfassung zur Seite Nr. 5
TABLE of CONTENTS Safety Notes Your Xerox Wide Format 721P Engineering Printer has been designed and tested to meet strict safety requirements. These include safety agency examination and approval and compliance to established environmental standards. Please read the following instructions carefully before operating the Xerox Wide Format 721P Engineering Printer and refer to them as needed to ensure the continued safe operation of the product. Follow all warnings and instructions marked on or s
Inhaltszusammenfassung zur Seite Nr. 6
INTRODUCTION Never remove any covers or guards that require a tool for removal. There are no operator serviceable areas within these covers. Never attempt any maintenance function that is not specified in this operator manual. Never defeat interlock switches. Machines are designed to prevent operator access to unsafe areas. Covers, guards, and interlock switches are provided to ensure that the system will not operate with the covers opened. Unplug the printer from the wall outlet and refer ser
Inhaltszusammenfassung zur Seite Nr. 7
INTRODUCTION EMC Notices Australia/New Zealand Changes or modifications to this equipment not specifically approved by Fuji XEROX Australia PTA. Limited may void the users authority to operate this equipment. Shielded cables must be used with this equipment to maintain compliance with the Radio communications Act 1992. European Union WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate mea
Inhaltszusammenfassung zur Seite Nr. 8
INTRODUCTION Japan This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. Changes or modifications to this equipment not specifically approved by Fuji XEROX Limited may void the users authority to operate this equipment. Shielded cables must be used
Inhaltszusammenfassung zur Seite Nr. 9
Introduction 1. Introduction Congratulations on acquiring your new XEROX Wide Format 721P Engineering Printer. Team XEROX looks forward to supporting and helping you to increase your organizational productivity. The integrated features, ease of operation, and reliability of the XEROX Wide Format 721P Engineering Printer will allow you to concentrate on your business and leave the printing to your XEROX Wide Format 721P Engineering Printer. This operator manual provides information that you nee
Inhaltszusammenfassung zur Seite Nr. 10
INTRODUCTION Organization And Content Of This Manual The XEROX Wide Format 721P OPERATOR MANUAL provides the information you need to become familiar with the components, features, operation, and specifications of your printer. It contains the following chapters: Chapter 1 Introduction This chapter shows the organization of this manual as well as the contents, terminology, and conventions used in this manual. Chapter 2 Specification This chapter contains product and media specifications, as well
Inhaltszusammenfassung zur Seite Nr. 11
INTRODUCTION Conventions Used In This Manual This manual uses the following conventions: Bold Boldface characters in the middle of a text string refer to selections on the control panel (for example, "press the Enter key"). WARNING: A WARNING indicates an operation, maintenance procedure, practice, condition or statement that, if not strictly followed, could result in personal injury. When included within a procedure, warnings always precede the step to which they refer. CAUTION: A CAUTION enco
Inhaltszusammenfassung zur Seite Nr. 12
INTRODUCTION This page is intentionally blank. 4 XEROX WIDE FORMAT 721P PRINTER OPERATOR MANUAL
Inhaltszusammenfassung zur Seite Nr. 13
PAPER DECK3 FM EXIT WIRE-CLEAN EX P-CL E AN CUT1 2 SE C ET4 D 21D PF D T © ¨ * N L 3D D 4 COPY ES NI Y MENU E E TR REE ST 2. Specification This chapter provides the product and media specifications for the XEROX Wide Format 721P Engineering Printer. It also provides the space requirements for normal operation after product installation. Product Specifications Process speed 240mm per second Resolution 400 dpi Environmental requirements Minimum: 50° F (10° C) at 20% relative humidity Maximum:
Inhaltszusammenfassung zur Seite Nr. 14
SPECIFICATION Media Specifications Media type Recommended media types: Bond 20 lb. (90 gsm) Vellum/Tracing 20 lb. (90 gsm) Film 4 mil thickness Media size Roll feed: Width 11 to 36 inches ( 279 to 914 mm) Length 500 ft ( 175 M) Roll Diameter 175mm maximum Core diameter 3 inches (76 mm) Manual Bypass Feed: Maximum Width 36 in. (E SEF) 914mm (A0) Minimum Width - 11 in. (A LEF) 279mm (A4) Print size Minimum 11 in. x 8.5 in. (A LEF) (A4) Maximum 36 in. x 48 in. (E SEF) (A0) Maxim
Inhaltszusammenfassung zur Seite Nr. 15
SPECIFICATION Room Space Requirements The illustration below shows the space requirements for normal operation of the printer after installation. Room Space Requirements Height 96 in. (2438 mm) (minimum) Width 157 in. (3988 mm) 66 in. (1676 mm) Depth 153.5 in. (3894 mm) 57.1 in. (1450 mm) Room Air Change 153.5 in. Requirements (3895 mm) (for Ozone Dissipation) 35 in. 39.4 in. 65 in. 721p (914 mm) (1000 mm) (1651 mm) Air should be cycled 5 times per hour (minimum) 48 in. (1220 mm) 157 in. (
Inhaltszusammenfassung zur Seite Nr. 16
SPECIFICATION This page is intentionally blank. 8 XEROX WIDE FORMAT 721P PRINTER OPERATOR MANUAL
Inhaltszusammenfassung zur Seite Nr. 17
PA PERDECK FM EXIT 1 2 3 4 D1 WIRE-CL EAN EXP-CL EAN CT U SELC ET 2D F P COPY D ESNITY MENU © ¨ * ENTER RESET D3 D4 3. Printer Overview This chapter shows the orientation of the printer. It also illustrates and describes its main components, as well as the elements of the operator panel. Printer Orientation The illustration below shows the printer orientation. You must be familiar with this orientation when following the messages in the message display and the instructions in this guide. 2 3
Inhaltszusammenfassung zur Seite Nr. 18
P APER DEC K FM EXIT 1 2 3 4 1 D WIRE- C LEAN EXP-CLEAN CUT S LECT 2D PF © ¨ * E C OPY DENS ITY M N EU ENT ER RESET 3D D4 PRINTER OVERVIEW Main Components Front Side View 10 9 11 1 2 3 8 4 5 6 7 1. Power On/Off Switch Press to switch the printer on and off. 2. Media Guide Adjust to size of cut sheet media in manual bypass mode. 3. Top Drawer (Roll 1) Open to load media roll and clear media jams. 4. Middle Drawer (Roll 2) Open to load media roll and clear media jams. 5. Bottom Drawer Open to l
Inhaltszusammenfassung zur Seite Nr. 19
PRINTER OVERVIEW Rear Side View 1 2 3 4 FOLDER DIAG. IF-VIII (CH-B) CONT. (IEEE1394) COM1 IF-VIII (CH-A) POWER 11 10 9 8 7 6 5 1. Top Rear Cover Pull the handle and open to clear media jams. 2. I/F Connector for Scanner Connect the cable from scanner here. (IEEE1394) Open to clear media jams. 3. Exit Cover 4. Power Cord Connect to a suitable power outlet. 5. Power (220 VAC) Connect the power cable from the controller here. 6. I/F VIII (CH-B) Connect the Interface Cable from the AccXES Contr
Inhaltszusammenfassung zur Seite Nr. 20
PRINTER OVERVIEW Right Side View 1 4 5 3 6 2 7 1. Toner Cartridge Replace when Status Display indicates that the cartridge is empty. 2. Media Cutter Turn to cut media during jam clearance. 3. Cutter Home Indicator As the cutter knob is rotated, the cutout color will change from RED to GREEN when the home position is reached. (DO NOT rotate counter-clockwise) 4. Meter A - Billing Square Counter for billing purposes. 5. Meter B - Service Linear Counter for service purposes. 6. Inner Transport Uni
