Inhaltszusammenfassung zur Seite Nr. 1
TD-8840 User Guide
ADSL2+ Modem Router
Rev: 2.0.1
1910010192
Inhaltszusammenfassung zur Seite Nr. 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2009 TP-LINK TECHNOLOGIES CO.,
Inhaltszusammenfassung zur Seite Nr. 3
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarante
Inhaltszusammenfassung zur Seite Nr. 4
EC DECLARATION OF CONFORMITY (EUROPE) In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, this product meets the requirements of the following standards: • EN55022 • EN55024 • EN60950 SAFETY NOTICES Caution: Do not use this product near water, for example, in a wet basement or near a swimming pool. III
Inhaltszusammenfassung zur Seite Nr. 5
CONTENTS Package Contents .................................................................................................... 1 Chapter 1. Introduction ........................................................................................ 2 1.1 Product Overview...................................................................................................... 2 1.2 Main Features ...........................................................................................................
Inhaltszusammenfassung zur Seite Nr. 6
4.3.6 DSL.................................................................................................................................42 4.4 Diagnostics.............................................................................................................. 44 4.5 Management ........................................................................................................... 45 4.5.1 Settings.....................................................................................
Inhaltszusammenfassung zur Seite Nr. 7
TD-8840 ADSL2+ Modem Router User Guide Package Contents The following items should be found in your package: One TD-8840 ADSL2+ Modem Router One AC power Adapter for TD-8840 ADSL2+ Modem Router One Resource CD for TD-8840 ADSL2+ Modem Router, including: • This Guide • Other Helpful Information • Quick installation Guide Program Quick installation Guide One RJ45 cable Two RJ11 cables One ADSL splitter Note: Make sure that the package contains the above items. If any of t
Inhaltszusammenfassung zur Seite Nr. 8
TD-8840 ADSL2+ Modem Router User Guide Chapter 1. Introduction Thank you for choosing the TD-8840 ADSL2+ Modem Router. 1.1 Product Overview With the excellent circuit design and high quality production, we guarantee the ADSL2+ Modem Router’s high performance, great stability and easy to use. The TD-8840 uses integrated ADSL2+ transceiver. The AFE supports full-rate ADSL connectivity conforming to the ITU and ANSI specifications. In addition to the basic DMT physical layer functions, the
Inhaltszusammenfassung zur Seite Nr. 9
TD-8840 ADSL2+ Modem Router User Guide Advanced DMT modulation and demodulation Real-time Configuration and device monitoring Quick response semi-conductive surge protect circuit, provides reliable ESD and surge-protect function 1.4 Supporting Protocol - G.992.1 (G.dmt) - Annex A/B/C - G.992.2 (G.lite) - Annex A/B/C - ANSI T1.413 - G.992.3 (ADSL2) - Annex A/B/C/M and Annex L (RE-DSL) compliant - G.992.5 (ADSL2+) Annex A/B/C and Annex L (RE-DSL) compliant - ADSL dual latency (fa
Inhaltszusammenfassung zur Seite Nr. 10
TD-8840 ADSL2+ Modem Router User Guide 1.7 System Support Support PVC Support NAT、DHCP and so on Support IEEE 802.3、IEEE 802.3u Support 10Base-T/100BASE-TX full-duplex or half duplex Ethernet Support Auto-MDIX 1.8 Working Environment Operating temperature: 0 ℃℃ ~40 Storage temperature: -40 ℃℃ ~70 Working Humidity: 10%~90% RH (non-condensing) Storage Humidity: 5%~90% RH (non-condensing) 4
Inhaltszusammenfassung zur Seite Nr. 11
TD-8840 ADSL2+ Modem Router User Guide Chapter 2. Hardware Installation Guide The TD-8840 maintains five separate interfaces: four Ethernet and one ADSL interface. The Router should not be located where it will be exposed to moisture or excessive heat. Place the Router in a location where it can be safely connected to the various devices. The electrical outlet shall be installed near the device and shall be easily accessible. 2.1 System Requirement Confirm your computer has been installe
Inhaltszusammenfassung zur Seite Nr. 12
TD-8840 ADSL2+ Modem Router User Guide 2.3 The Rear Panel ON/OFF: Turn on/off the ADSL2+ Modem Router’s power. POWER: Please do not use any unknown power adapter; otherwise your ADSL2+ Modem Router may be damaged. RESET (reset default): With the Router powered on, use a pin to press and hold the Reset button for at least 5 seconds. And then release the button and wait the Router to reboot to its factory default settings. 1~4(LAN): Connect with your computer’s NIC. LINE (WAN): Co
Inhaltszusammenfassung zur Seite Nr. 13
TD-8840 ADSL2+ Modem Router User Guide Third Step: Plug one end of the AC Power Adapter into the Power jack on the Router and the other end to a standard electrical outlet. Last Step: Check the line connection to see if everything is ready. Power up finally. Figure 2-1 7
Inhaltszusammenfassung zur Seite Nr. 14
TD-8840 ADSL2+ Modem Router User Guide Chapter 3. Quick Installation Guide 3.1 Configure PC After you directly connect your PC to the TD-8840 or connect your adapter to a Hub/Switch which has connected to the Router, you need to configure your PC’s IP address. Now you have two ways to configure the TCP/IP protocol below: Setting IP address automatically Step 1: Click the Start menu on your desktop, right click My Network Places, and then select Properties (shown in Figure 3-1). Fig
Inhaltszusammenfassung zur Seite Nr. 15
TD-8840 ADSL2+ Modem Router User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button. Figure 3-3 Step 4: Select “Obtain an IP address automatically” and “Obtain DNS server address automatically” in the screen below. And then click OK. 9
Inhaltszusammenfassung zur Seite Nr. 16
TD-8840 ADSL2+ Modem Router User Guide Figure 3-4 Setting IP address manually The default IP address of the ADSL2+ Modem Router is 192.168.1.1, and the default Subnet Mask is 255.255.255.0. These values can be seen from the LAN, and can be changed as your desire. As an example, we use the default values for description in this guide. Step 1: Select Use the following IP address radio button in the next screen. Step 2: Enter the IP address as 192.168.1.* (* is any value between 2 to 25
Inhaltszusammenfassung zur Seite Nr. 17
TD-8840 ADSL2+ Modem Router User Guide Figure 3-5 Note: 1) Users of Windows 98 can open TCP/IP Properties according to the following: Right-click (Mouse) Network Neighbor Choose Properties - Double-click TCP/IP. 2) Users of Windows 2000/NT/XP can do the following: Right-click Network Neighbor Choose Properties Right-click Local Connection Choose Properties Double-click Internet Protocol (TCP/IP). 3) The words in fact may be different with this guide. Now, you can run the Pi
Inhaltszusammenfassung zur Seite Nr. 18
TD-8840 ADSL2+ Modem Router User Guide Figure 3-6 If the screen looks like the following, the connection has failed. Please try again. Figure 3-7 3.2 Login Open your web browser and enter http://192.168.1.1 in the address bar of the browser. When ADSL connection is OK, the following login box will pop up. Enter default user name (admin) and password (admin) as shown in Figure 3-8. Click OK to enter the Web-based Utility of the Router. Figure 3-8 12
Inhaltszusammenfassung zur Seite Nr. 19
TD-8840 ADSL2+ Modem Router User Guide 3.3 Quick Setup Figure 3-9 is the main page of the Router. Figure 3-9 Please select Quick Setup. Enter the VPI and VCI values provided by your ISP and click Next. Figure 3-10 Select the relevant Connection Type and Encapsulation Mode provided by your ISP and click Next. 13
Inhaltszusammenfassung zur Seite Nr. 20
TD-8840 ADSL2+ Modem Router User Guide 3.3.1 PPPoA a) Select PPP over ATM (PPPoA) Connection Type, and click Next. Figure 3-11 b) Enter the Username and Password provided by your ISP and click Next. Figure 3-12 14
