Inhaltszusammenfassung zur Seite Nr. 1
GENUINE REMOTE ENGINE START
USER’S INSTRUCTIONS
Parts number：C930 V7 620
Thank you for purchasing a genuine Mazda accessory.
Before use, be sure to thoroughly read these instructions.
Please read the contents of this booklet in order to properly use the Remote Engine Start.
Your safety depends on it.
After using this instruction manual, store it in a place where it can be easily located.
Note, consult your authorized Mazda dealer, or a dealer appointed store, for proper
vehicle inst
Inhaltszusammenfassung zur Seite Nr. 2
CONTENTS 1. Remote Engine Start features ....................................................................... 3 2. Safety precautions ........................................................................................ 3 3. General information....................................................................................... 6 4. Operating precautions................................................................................... 7 5. Part names............................
Inhaltszusammenfassung zur Seite Nr. 3
1. Remote Engine Start features The Remote Engine Start allows the user to start the engine of a vehicle from a remote location using a remote control. The user can turn on the air conditioner / heater beforehand so the cabin of the vehicle can be cooled or heated ahead of time. The user can check the status of the vehicle from a remote location. 2. Safety precautions WARNING Do not install this device on a vehicle equipped with a manual transmission. ● Only install this d
Inhaltszusammenfassung zur Seite Nr. 4
WARNING Do not start up the engine using the Remote Engine Start when parked on an incline. ● If the vehicle were to move unintentionally due to the engine vibration, jolt, etc., it could result in a serious accident. Performing safe maintenance and inspection. ● When performing vehicle inspection and maintenance, remove the (-) terminal on the vehicle battery. Never start up the engine with the remote control during inspection or maintenance at a gas or service station, etc.
Inhaltszusammenfassung zur Seite Nr. 5
WARNING Fire prevention. ● Do not start the engine when the vehicle is near something flammable (oil or dry grass). Otherwise, the high temperature from the exhaust fumes or exhaust pipe could cause a fire. ● Do not start the engine while the vehicle is wrapped with a body cover. Otherwise, the high temperature from the exhaust fumes or exhaust pipe could cause a fire. Do not pour water on the remote control. ● The remote control is water resistant for exposure during daily
Inhaltszusammenfassung zur Seite Nr. 6
3. General information -Laws in some communities may restrict the use of remote starters. For example, some laws may require a person using the remote start to have the vehicle in view when doing so. Check local regulations for any requirements on remote starting of vehicles. -This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interferenc
Inhaltszusammenfassung zur Seite Nr. 7
4. Operating precautions Usage Environment ●The remote control signal (or the response signal from the controller) may not reach the controller (or the remote control) if there are strong radio waves transmitting nearby, or if there are obstacles blocking the signal. ● The engine may be slow to start during severe cold weather conditions. Vehicles with Remote Control Door Lock Function ●Door Lock and Door Unlock Function by the remote control keyless entry or advanced keyless ent
Inhaltszusammenfassung zur Seite Nr. 8
Remote Control Handling Instructions The remote control is a sensitive electronic device similar to a cellular telephone. Please follow the handling instructions below to avoid damage to or breakdown of the remote control. ● Avoid storing or using the remote control in places that expose it to direct sunlight, places that have high humidity, places with extremely high temperatures (on top of the dashboard, etc.) or places with extremely low temperatures (leaving inside the vehicle whil
Inhaltszusammenfassung zur Seite Nr. 9
5. Part names Remote Control CAUTION ・ Keep the remote control out of the reach of children. Otherwise, they may swallow the lithium battery accidentally and choke. ・ Do not drop the remote control or hit it against something hard. Otherwise, it can result in breakdown or malfunction. ・ Do not pour water on the remote control or submerge it. It can result in breakdown or malfunction. Front Back Side Side Car find Function switch switch Start switch FCC/IC
Inhaltszusammenfassung zur Seite Nr. 10
6. Display Display Name Description Antenna mark Turns on when sending or receiving a signal. Send mark Flashes when sending a transmission signal. Receive mark Flashes when receiving a signal. Send error mark Turns on when a signal for the same frequency band is being used. Battery mark Turns on when the battery life is low. Time display Displays the engine warm up time. Car find display Turns on when conducting the car find operation. Error display An error d
Inhaltszusammenfassung zur Seite Nr. 11
7. Basic functions for Remote Engine Start Engine Start & Stop Function The remote control is equipped with engine start, engine stop and automatic stop (set with timer) functions. In addition, the engine start operation will perform when conditions outlined on page 14 are Engine start → p.15 satisfied. The air conditioner / heater can be turned on beforehand Engine stop → p.18 so the cabin of the vehicle can be cooled or heated ahead of time. Rear Defrost Function The rea
Inhaltszusammenfassung zur Seite Nr. 12
Car Find Function If the car find operation is performed on the remote control, Car find the hazard lights will flash twice and the horn will sound twice so you can confirm the vehicle’s location. This function is convenient when looking for your vehicle in a large Directions for car find parking lot, etc. operation → p. 25 Answer Back Function This device conducts bidirectional communication between the remote Answer back control and the controller (vehicle side). The user
Inhaltszusammenfassung zur Seite Nr. 13
8. Low battery warning & replacement directions When the battery is running out and the user tries to conduct an operation, the “Low battery warning” on the LCD monitor will display. In this situation, be sure to replace both batteries at the same time with new ones. The performance will go down particularly under cold conditions. Battery type: Lithium battery CR2032 / Qty. 2 ・ Release the clasps and slide off Battery cover the battery cover to remove. Clasps ADVICE If t
Inhaltszusammenfassung zur Seite Nr. 14
9. Basic operations CAUTION Check points when the vehicle is parked. When using the engine start function with this device, follow the instructions below when parking, in order to avoid vehicle theft or an accident from occurring. ・ Be sure to always engage the parking brake. ・ Put the shift lever in the “P” position. ・ Be sure there is no advanced or smart key inside the vehicle. ・ Close all doors and windows. ・ Lock the doors. ・ Close the hood. ・ Turn off the w
Inhaltszusammenfassung zur Seite Nr. 15
Within 2 sec. 9-1. Engine start operation Press the function switch once. The LCD display will appear as shown on the right. ADVICE The LCD display will appear when the Function switch switch is released. Press the start switch while the above LCD display is shown until it beeps. After the send mark flashes, the send operation is completed. After the send operation is completed, the controller will send an answer back signal. *Press the start switch within 2 seconds
Inhaltszusammenfassung zur Seite Nr. 16
LCD Display During Engine Start Operation The LCD display will change as shown below depending on the status of the vehicle, the signal transmission and the switch operation. Condition Error Display (Safety detection display description) If the safety detection function is turns on, initiated by the vehicle status, the following display will appear on the LCD monitor. Be sure to check the vehicle status once more. Error Display Display Description Troubleshoot Vehicle transmiss
Inhaltszusammenfassung zur Seite Nr. 17
When the start switch is Press the function not pressed while the switch once. LCD display is shown. Press the start switch while the LCD display is shown until it Timeout beeps. 送信 Send Send error Engine Condition Receive start error error standby Condition Engine Engine Receive error start start error initiated standby Condition Engine Receive Engine error start error start standby initiated 17
Inhaltszusammenfassung zur Seite Nr. 18
9-2. Engine stop operation This operation only applies when the engine has been started with the remote control. Press the stop switch until it beeps. The LCD display will appear as shown on the right. After the send mark flashes, the send operation is Stop switch completed. After the send operation is completed, the controller will send an answer back signal. When the remote control receives a response from the vehicle, it indicates the engine stop operation with a display
Inhaltszusammenfassung zur Seite Nr. 19
● Other Engine Stop Conditions The engine will stop if one of the following conditions is true. 1) The hood is opened. 2) The shift lever is put in a position other than the “P” position. 3) A door is opened. 4) The push start switch is pressed. 5) The pre-set warm up time has elapsed. 6) The brake pedal is engaged. 7) The accelerator pedal is engaged (the engine stops by the rpm restriction). 8) There is an advanced key or smart key inside the vehicle. To
Inhaltszusammenfassung zur Seite Nr. 20
While LCD displays 9-3. Warm up time check This operation only applies when the engine has been started with the remote control. Press the function switch once. The LCD display will appear as shown on the right. ADVICE Function switch The LCD display will appear when the switch is released. Press the start switch while the above LCD display is shown until it beeps. After the send mark flashes, the send operation is completed. After Start switch the send operation
