Inhaltszusammenfassung zur Seite Nr. 1
Important: Keep these
instructions for future
reference
Gate Instructions
Assembly and Installation Instructions
It is preferable to in stall the extension on the hinge side of
the gate. If you have an application that re quire s additional
extensions, please contact the retailer which you
Please read these instructions carefully.
purchased your gate from. We offer, the following sizes of
Please follow these instructions carefully to ensure that extensions for your gate: 4 inch, 6 inch, 12 inch
Inhaltszusammenfassung zur Seite Nr. 2
Important: Keep these instructions for future reference Gate Instructions 3. Extensions List Item NO. 8 Extension 6 Extension MAX Size 12 Extension 4 Extension 1152 29--52 inches 1154 29--52 inches 1158 29--58 inches 1160 29--38 inches 1164 29--52 inches 1165 29--44 inches 1166H 29--40 inches (2)
Inhaltszusammenfassung zur Seite Nr. 3
Important: Keep these instructions for future reference Gate Instructions Assembling and Installing Your Gate **Note: IMPORTANT you will notice a slight Gap between the gate door latch and the frame tube . THIS IS NOT A DEFECT . Your gate is a pr essur e mounted gate and this gap will disappear once you tighten your gate in the doorway. Step 1. Begin by locating the 4 Threaded Spindle Rods. Before you begin, turn the Adjustment Wheels clockwise until they are almost against the flat end of the
Inhaltszusammenfassung zur Seite Nr. 4
Important: Keep these instructions for future reference Gate Instructions Step 3. Positioning and Attaching the Wall Cups to your door opening. Your gate is a pressure mounted gate. Therefore it is not necessary to use the screw attached Wall Cups to your door opening if you choose not to. However, IF YOU ARE USING THE GATE AT THE TOP OF STAIRS YOU MUST USE THE WALL CUPS. Regardless of whether you are using your gate at the top of stairs or not, using the Wall Cups will affix your gate more firm
Inhaltszusammenfassung zur Seite Nr. 5
Important: Keep these instructions for future reference Gate Instructions Step 4. You ar e now r eady to install your gate in the doorway. Begin by positioning your gate level and center ed in the doorway opening. Pull the 4 Thr eaded Spindle Rods out of the ends of the frame Tubes until the Flat Plastic End touches the wall. **If you ar e using the Wa ll Cups then the flat plastic ends of the Thr eaded Spindle Rods should go into the Wall Cups that ar e fastened to your wall. Next, while holdin
Inhaltszusammenfassung zur Seite Nr. 6
Important: Keep these instructions for future reference Gate Instructions Step 5. Yo u ar e now r e ady to do the Final Adjustment to fasten your gate firmly in the doorway. Start by turning the BOTTOM Adjustment Wheels FIRST. Continue to turn the lower Adjustment Wheels counter-clockwise until the Adjustment Wheels are firmly against the ends of the frame tubes. . IMPORTANT: Ther e should be equal space on each side of the gate. To easily determine this look at the length of thr eaded r o d is
Inhaltszusammenfassung zur Seite Nr. 7
Important: Keep these instructions for future reference Gate Instructions Next, tighten the top 2 Adjustment Wheels by turning them counter-clockwise. Again, make sure both sides are equal as you tighten. As you tighten the Adjustment wheels you will notice the gap between the plastic gate door latch and the frame tube is narrowing. As the gap continues to narrow continue turning the upper Adjustment Wheels until the frame tube engages in the slot in the plastic gate door handle. Leave a 1/16”
Inhaltszusammenfassung zur Seite Nr. 8
Important: Keep these instructions for future reference Gate Instructions Diagram G1: How to open the Gate Door. Diagram G2: How to close and lock the Gate Door. Step3 Step1 Step2 Step2 Step1 Step3 Diagram G2 . Diagram G1 Step 1: Slide the Safety Lock back. Step 1: Close the Gate Door Step 2: You can now lift up the Handle Step 2: Push Handle down. The Gate is now closed. Step 3: The Gate Door can now swing open. Step 3: For added security, push back on the Safety Lock
Inhaltszusammenfassung zur Seite Nr. 9
Important: Keep these instructions for future reference Gate Instructions Instructions for Gate Extension 1. Assemble the gate per the gate instructions. 2. Choose the side of the gate to be extended and remove the top and bottom Adjustment Wheel Spindles. 3. Assemble the gate and extension as illustrated. 4. Reposition the gate and fit in accordance with the gate fitting instructions. REMOVING YOUR GATE FROM THE WALL To r em o v e y ou gate fr om the wall begin by turning the Adjustment Whe
