Inhaltszusammenfassung zur Seite Nr. 1
Industrial Monochrome CCD Camera
CV-M300
Operation Manual
(Rev.E)
Inhaltszusammenfassung zur Seite Nr. 2
CV-M300 DECLARATION OF CONFORMITY AS DEFINED BY THE COUNCIL DIRECTIVE 89/336/EEC EMC (ELECTROMAGNETIC COMPATIBILITY) WE HEREWITH DECLARE THAT THIS PRODUCT COMPLIES WITH THE FOLLOWING PROVISIONS APPLYING TO IT. EN-50081-1 EN-50082-1
Inhaltszusammenfassung zur Seite Nr. 3
CV-M300 Table of Contents Table of Contents ....................................................................................................................................... 2 1. General ................................................................................................................................................ 3 2. Standard Composition......................................................................................................................... 3 3. Main Featu
Inhaltszusammenfassung zur Seite Nr. 4
CV-M300 1. General The CV-M300 is a monochrome 2/3" CCD camera designed for automated imaging applications featuring high performance and unique functions within a uniform and compact housing. The high-speed shutter function and asynchronous random trigger function allow the camera to capture high quality images of fast moving objects. It is suitable for industrial applications such as on-line inspection and measurements. In addition to conventional random trigger modes, the newly added pulse wi
Inhaltszusammenfassung zur Seite Nr. 5
CV-M300 4. Locations and Functions 1 2/3" interline transfer CCD sensor. 2 Lens mount of C-mount type. *1) 3 BNC connector for video output. 4 Switch block SW1 for shutter speed and function modes setting. 5 6-pin multi connector for WEN and EEN output external trigger input. 6 12-pin multi connector for +12V DC power, video output and HD/VD input/output. 7 GAIN potentiometer for manual gain adjustment. 8 Screw holes for Tripod mount plate. 9 Tripod mount plate to place the camera on tripod. Not
Inhaltszusammenfassung zur Seite Nr. 6
CV-M300 5. Pin Assignment 5.1. 12-pin Multi-connector (DC-IN/SYNC.) Type: HR10A-10R-12PB-01 (Hirose) male Seen from rear. Pin no. Signal Remarks 1 GND 2 +12 V CD input 3 GND 4 Video output Parallel with the BNC video output. Avoid double termination. 5 GND 6 HD input/output HD in as factory setting. *1) 7 VD input/output VD in as factory setting. *1) *2) 8 GND 9 NC NC as factory setting. Pixel clock output. *1) 10 GND 11 +12 V CD input 12 GND Notes: *1) Signals on pin no. 6, 7 and 9 can be chang
Inhaltszusammenfassung zur Seite Nr. 7
CV-M300 6. Functions and Operations 6.1. Input/Output of HD/VD Signal 6.1.1. Input of External HD/VD Signal As factory setting the camera can be synchronized by external HD/VD signals. The signal level must be 4.0 Vp-p ± 2.0V at the input with the 75 Ohm termination ON. To change to non-terminated input, see instructions in “7. Mode Setting”. If no ext. HD is connected, the camera will switch to the internal X-tal controlled HD. If no ext. VD is connected, the camera will continue with its inter
Inhaltszusammenfassung zur Seite Nr. 8
CV-M300 To use this mode Set: SW1-4 to ON for ext. trigger shutter SW1-5 to OFF for field accumulation SW1-6 to ON for non-interlaced SW1-1, 2 and 3 to shutter speed Input: Ext. trigger to pin 5 on 6 pin multi connector. Ext. HD to pin 6 on 12-pin multi connector. (If used). 75 Ohm termination is done with SW2-1 (HD) on PK8041 board. Refer to Timing Chart and Cautions on next page. Detailed switch and jumper setting is described in “7. Mode Setting”. For connections see “5. Pin Assignment”. Caut
Inhaltszusammenfassung zur Seite Nr. 9
CV-M300 CCIR (Non-interlaced / Field accumulation mode) Edge pre-select mode (for non-interlace only) CCIR : 1H = 64µ s TRIG 1H TRIG in >1H EXT HD INT HD INT VD 1.5H 7.5H 7.5H 6.5H 1.5H 7.5H EEN Exposure time 16.5H Exposure time 0.5H 0.5H WEN 9H 7.5H 10H 14H CCD out Effective pixels No.10 to 251 Video out 25H 287H 25H Blanking Effective video Blanking 6.3.2. Pulse Width Control Mode The pulse width control mode will only work in non-interlaced field accumulation mode. The exposure is controlled
Inhaltszusammenfassung zur Seite Nr. 10
CV-M300 Cautions in the Pulse Width Control Mode. 1. Pulse width control mode is effective only in non-interlaced field accumulation mode. 2. The exposure start may be delayed up to 1H max., when the falling edge of ext. trigger pulse is not synchronized with the falling edge of ext. HD signal. To avoid this 1H jitter and delay, the falling edge of the ext. trigger pulse should be synchronized within 4.4 usec. to the HD pulse. It can be the ext. HD in or the Internal HD out. See cautions in Edge
Inhaltszusammenfassung zur Seite Nr. 11
CV-M300 6.3.3. Start/Stop Trigger Mode The Start /Stop trigger will work in 3 modes: 1. Interlaced with frame accumulation. 2. Interlaced with field accumulation. 3. Non-interlaced with field accumulation. The exposure time is controlled by the interval between the ext. trigger pulse and the ext. VD signal. The exposure starts at the first HD pulse after the falling edge of the ext. trigger, and stops at the rising edge of the VD pulse. The range can be within 1/77 to 1/10,000 sec. The Start/Sto
Inhaltszusammenfassung zur Seite Nr. 12
CV-M300 Cautions in the Start/Stop Trigger Mode. 1. The input of ext. VD signal must be given continuously to synchronize with int. VD signal. It is not possible to input ext. VD signal randomly. 2. The exposure start may delay up to 1H max., when the falling edge of ext. trigger pulse is not synchronized with the falling edge of ext. HD signal. To avoid this 1H jitter and delay, the falling edge of the ext. trigger pulse should be synchronized within 4.4 usec. to the HD pulse. It can be the ext
Inhaltszusammenfassung zur Seite Nr. 13
CV-M300 6.3.4. Long Time Exposure Mode The Long time exposure will work in 3 modes: 1. Interlaced with field accumulation. 2. Interlaced with frame accumulation. 3. Non-interlaced with field accumulation. The exposure time is the interval between 2 ext. VD pulses sent to the camera VD input. Each ext. VD pulse will reset and restart the internal VD in the camera as for ext. HD/VD input. So the camera is synchronized to the external HD/VD supply after each VD input. An exposure starts after input
Inhaltszusammenfassung zur Seite Nr. 14
CV-M300 Cautions in the Long Time Exposure Mode. 1. Theoretical exposure time is as follows. EIA: 1/30 sec. to ∞. CCIR: 1/25 sec. to ∞. 2. It is recommended not to use exposure >2 sec. since visible dark-current noise may occur. 3. Ext. HD signal (4.0 Vp-p ± 2.0V at 75 Ohm terminated) has to be input continuously The falling edge of Ext. HD signal and Ext. VD signal are phase-synchronized. 4. Timing of ext. VD signal in each accumulation mode has to be set, as described before. a) 2:1 Interlaced
Inhaltszusammenfassung zur Seite Nr. 15
CV-M300 7. Mode Setting Cautions on Mode Setting. Before making any mode or jumper setting turn the power OFF. 7.1.1. SW1 Switch on the Rear Panel Factory settings for SW1 are with all 8 switches in OFF position. OFF = < ON = > Seconds SW1 OFF ON 1 < < < < > > > > < < > > < < > > SHUTTER 2 < > < > < > < > 3 TRIGGER 4 Normal < > External trigger ACCUM 5 Field < > Frame INTERLACE 6 Interlaced < > Non-interlaced GAMMA 7 1.0 < > 0.45 GAIN 8 Manual < > Auto The
Inhaltszusammenfassung zur Seite Nr. 16
CV-M300 Cautions on Shutter. The image can flicker when the illumination is AC powered. Highlighted parts of the image will show increasing smear at a shorter shutter time. 7.1.4. Ext. Trigger Shutter Mode When trigger select SW1-4 is ON. The camera is in ext. trigger shutter mode. The SW1-1, SW1-2 and SW1- 3 are for selecting the shutter speed. The range is from OFF to 1/10,000 second in 8 steps. For each external trigger pulse, the camera will make an exposure with the selected shutter speed.
Inhaltszusammenfassung zur Seite Nr. 17
CV-M300 7.3. Jumper Settings Cautions on Jumper Setting. Before making any mode or jumper setting turn the power OFF. Jumpers for mode setting are found on the boards PK8041 & PK8042. The following modes are available with jumper setting: Input/Output Mode of HD/VD signal. (HD/VD input is factory setting) Edge Pre-select Mode. (Factory setting) Pulse Width Control Mode Start/Stop Trigger Mode Long Time Exposure Mode Set the jumpers according to the list below in 7.3.1. and 7.3.2. The jumper posi
Inhaltszusammenfassung zur Seite Nr. 18
CV-M300 7.4. Location of SW2 and Jumpers Jumpers are shorted with a 0 Ohm resistor or by a soldering between the 2 points. To remove the solder tin from a jumper position, use a special tin remover such as de-soldering wick. 7.4.1. Board PK8041 Side A JP8 JP9 SW2 JP7 JP10 JP12 JP11 JP13 JP6 7.4.2. Board PK8042 Side A JP14 - 17 -
Inhaltszusammenfassung zur Seite Nr. 19
CV-M300 8. Adjustment of Video Signal Output Level When an alignment of a video output signal is required, remove the camera housing and adjust potentiometers VR3, VR4 and VR5 on the PK8042 board while measuring their levels at the video output connector. This adjustment should only be done in a setup with a standard TV test chart and controlled illumination. VR3: To adjust the gain level of AGC. (Factory setting: 700 mVp-p ± 30 mV) VR4: To adjust the white level. (Factory setting: 800 mVp-p ± 2
Inhaltszusammenfassung zur Seite Nr. 20
CV-M300 9. External Appearance Unit : mm (inches) 550 (0.2) (1.97) 4-M3 26 (1.02) 50 80 12.7 (1.97) (3.15) (0.5) 40 (1.57) 20 (0.79) 550 (0.2) (1.97) C-MOU NT 26 (1.02) 4-M3 5 Tripod mount plate 6 (0.2) 56 (2.20) +0.1 50 (1.97) ł6 0 4-ł3.5 14 (0.55) (1.02) (1.18) 40 26 30 (1.57) 4-R2 4-M3 34 (1.33) U1/4-20 ound-top ews):R Accessory(Scr ews Scr M3x5 Bzn 4pcs - 19 -
