Inhaltszusammenfassung zur Seite Nr. 1
QUI C K STAR T
®
Spectra IV SL and
Spectra IV SE Series
Dome Systems
23X, 27X, and 35X Models
C3462M (9/09)
Inhaltszusammenfassung zur Seite Nr. 2
Installing the Dome Drive 1. Perform one of the following options: • View video using both analog and IP connections: Set the DIP switches on the top of the Spectra IV dome drive (refer to Figure 12). For DIP switch settings, refer to the labels located on the top of the dome drive, or refer to Switch Settings on page 3. • View video using the IP connection: If your dome drive is part of a Spectra IV IP system, you do not need to set the DIP switches. NOTE: When connecting more than one Spectra
Inhaltszusammenfassung zur Seite Nr. 3
SWITCH SETTINGS WARNING: If you are using Pelco D-type or P-type control, your system may not operate if the baud rate and address switches are not set correctly. The switches are set at the factory at the defaults for Pelco D-type control (2400 baud and address 1). Table A. Switch Settings for SW2 Special Systems Switch Number 123456789 10 AD-32 Preset System ON CM9502 Setting ON Pelco Coaxitron Controller OFF Third-Party Coaxial Control ON Third-Party Pelco P-type Control ON Serial Port Set
Inhaltszusammenfassung zur Seite Nr. 4
Table B. Switch Settings for SW1, P-Type Control NOTE: For Coaxitron controls, SW1 is not used; set all switches to OFF. For D-type control systems, refer to Table C. SWITCH SETTING SWITCH SETTING SPECTRA SPECTRA ADDRESS ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 1 OFF OFF OFF OFF OFF 17 OFF OFF OFF OFF ON 2 ON OFF OFF OFF OFF 18 ON OFF OFF OFF ON 3 OFF ON OFF OFF OFF 19 OFF ON OFF OFF ON 4 ON ON OFF OFF OFF 20 ON ON OFF OFF ON 5 OFF OFF ON OFF OFF 21 OFF OFF ON OFF ON
Inhaltszusammenfassung zur Seite Nr. 5
SWITCH SETTING SWITCH SETTING SPECTRA SPECTRA ADDRESS ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 31 ON ON ON ON ON OFF OFF OFF 71 ON ON ON OFF OFF OFF ON OFF 32 OFF OFF OFF OFF OFF ON OFF OFF 72 OFF OFF OFF ON OFF OFF ON OFF 33 ON OFF OFF OFF OFF ON OFF OFF 73 ON OFF OFF ON OFF OFF ON OFF 34 OFF ON OFF OFF OFF ON OFF OFF 74 OFF ON OFF ON OFF OFF ON OFF 35 ON ON OFF OFF OFF ON OFF OFF 75 ON ON OFF ON OFF OFF ON OFF 36 OFF OFF ON OFF OFF
Inhaltszusammenfassung zur Seite Nr. 6
SWITCH SETTING SWITCH SETTING SPECTRA SPECTRA ADDRESS ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 111 ON ON ON ON OFF ON ON OFF 151 ON ON ON OFF ON OFF OFF ON 112 OFF OFF OFF OFF ON ON ON OFF 152 OFF OFF OFF ON ON OFF OFF ON 113 ON OFF OFF OFF ON ON ON OFF 153 ON OFF OFF ON ON OFF OFF ON 114 OFF ON OFF OFF ON ON ON OFF 154 OFF ON OFF ON ON OFF OFF ON 115 ON ON OFF OFF ON ON ON OFF 155 ON ON OFF ON ON OFF OFF ON 116 OFF OFF ON OFF ON ON
Inhaltszusammenfassung zur Seite Nr. 7
SWITCH SETTING SWITCH SETTING SPECTRA SPECTRA ADDRESS ADDRESS SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 191 ON ON ON ON ON ON OFF ON 223 ON ON ON ON ON OFF ON ON 192 OFF OFF OFF OFF OFF OFF ON ON 224 OFF OFF OFF OFF OFF ON ON ON 193 ON OFF OFF OFF OFF OFF ON ON 225 ON OFF OFF OFF OFF ON ON ON 194 OFF ON OFF OFF OFF OFF ON ON 226 OFF ON OFF OFF OFF ON ON ON 195 ON ON OFF OFF OFF OFF ON ON 227 ON ON OFF OFF OFF ON ON ON 196 OFF OFF ON OFF OFF O
Inhaltszusammenfassung zur Seite Nr. 8
Preset 95: Accessing the Main Menu You can call up the main menu on your monitor by programming (setting or creating) preset 95 (preset 28 in AD32-preset mode). Programming preset 95 for Pelco’s controllers varies according to the type of controller you are using. Instructions for programming preset 95 are given below for various Pelco controllers. Refer to the instructions shipped with your controller for more information. CM6700/CM6800 1. Enter the number of the Spectra IV dome system and
Inhaltszusammenfassung zur Seite Nr. 9
MPT9500 Extended Coaxitron or RS-485 Mode 1. Enter 95 and press the PRESET SET key. 2. Press the F2 key. The main menu appears. NET300/NET350/NET4001A 1. Check the Set box. 2. Click the preset 95 button. The main menu appears. ENDURA WORKSTATION 1. Right-click in the video pane of the Spectra IV dome system. 2. Click Preset and then click Select Preset. 3. Enter 95 and then click OK. VCD5000 1. Enter 95 for the preset action. The shortcuts menu appears. 2. Press the Preset button on the KBD5000
Inhaltszusammenfassung zur Seite Nr. 10
Troubleshooting To use your dome, refer to the installation and operation/configuration manuals on the resource disc. If the following instructions fail to solve your problem, contact Pelco Product Support at 1-800-289-9100 (USA and Canada) or +1-559-292-1981 (international) for assistance. Be sure to have the serial number available when calling. Do not try to repair the unit yourself. Leave maintenance and repairs to qualified technical personnel only. Table D. Troubleshooting the Spectra IV
Inhaltszusammenfassung zur Seite Nr. 11
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in • Six months: material or workmanship for a period of one year after the date of shipment. – All pan and tilts, scanners, or preset lenses used in continuous motion applications (preset scan, tour, and auto scan modes). Exceptions to this warranty are as noted below: Pelco will warrant all replacement parts and repairs for 90 days from the date of • Five years: Pelco
Inhaltszusammenfassung zur Seite Nr. 12
www.pelco.com Pelco, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel (800) 289-9100 Fax (800) 289-9150 International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120
