Inhaltszusammenfassung zur Seite Nr. 1
Snapshot
LEDsplash™ 152B
Use on Dimmer
Outdoor Use
Sound Activated
DMX
Master/Slave
115V/230V
Switch
Replaceable
Fuse
User Serviceable
Duty Cycle
User Manual
th
3000 N 29 Ct, Hollywood, FL 33020 U.S.A.
(800) 762-1084 – (954) 929-1115
FAX (954) 929-5560
www.chauvetlighting.com
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS 1. Before You Begin ...................................................................................................................................... 3 What is included .............................................................................................................................................. 3 Unpacking Instructions .................................................................................................................................... 3 A
Inhaltszusammenfassung zur Seite Nr. 3
1. BEFORE YOU BEGIN What is included 1 x LEDsplash™ 152B Warranty Card User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials. In th
Inhaltszusammenfassung zur Seite Nr. 4
Safety Instructions Please read these instructions carefully, which includes important information about the installation, usage and maintenance of this product. Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel
Inhaltszusammenfassung zur Seite Nr. 5
2. INTRODUCTION Features 6-channel DMX-512 LED wash light Blackout/static/dimmer/strobe Selector switch for sound active or automatic programs Static colors and RGB color mixing with or without DMX controller Built-in automated programs via master/slave or DMX Built-in sound activated programs via master/slave or DMX Additional Features Linkable with LED Shadow™, LED Shadow™ 2, LED Techno Strobe™, LED Techno Strobe™ RGB, LEDsplash™ 200B and LEDsplash™ 2 in stand alone DMX Ch
Inhaltszusammenfassung zur Seite Nr. 6
Product Overview Satellite™ Power Input connection (Hardwired cable) Safety Power LED attachment point Indicator Microphone Sensitivity Fuseholder Adjustment Knob DMX, Master/Slave Bracket Signal LED Indicator Adjustment Knob Standalone Auto/Sound Selection Switch DIP Switches DMX Out Bracket Adjustment Knob DMX In LEDsplash™ 152B User Manual 6 3/9/2010 3:02 PM
Inhaltszusammenfassung zur Seite Nr. 7
Product Dimensions LEDsplash™ 152B User Manual 7 3/9/2010 3:02 PM
Inhaltszusammenfassung zur Seite Nr. 8
3. SETUP Disconnect the power cord before replacing a fuse, and always replace with the same type fuse. Fuse Replacement With a Phillips #2 screwdriver, unscrew the fuse holder from its housing. Remove the damaged fuse from its holder and replace with exact same type fuse. Screw the fuse holder back in its place and reconnect power. The fuse is located inside this compartment. Remove using a Phillips #2 screwdriver. FUSE Fixture Linking You will need a serial data link
Inhaltszusammenfassung zur Seite Nr. 9
CABLE CONNECTORS Cabling must have a male XLR connector on one end and a female XLR connector on the other end. Resistance 120 DMX connector configuration 1 ohm ¼ W between 3 pin 2 (DMX -) and 2 pin 3 (DMX +) of COMMON the last fixture. 1 1 DMX + INPUT 3 OUTPUT 3 Termination reduces signal errors. To 2 2 avoid signal transmission problems DMX - and interference, it is always advisable to connect a DMX signal terminator. CAUTION Do not allow contact between the common and t
Inhaltszusammenfassung zur Seite Nr. 10
Master/Slave Fixture Linking 1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the first fixture. 2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then, proceed to connect from the output as stated above to the input of the following fixture and so on. Often, the setup for Master-Slave and Standal
Inhaltszusammenfassung zur Seite Nr. 11
4. OPERATING INSTRUCTIONS Operation Stand-Alone Mode (Sound-Active, Auto Mode): This mode allows a single unit to run to the beat of the music, or the unit will auto change in Auto Mode. 1) Set dipswitches position to Sound Active or Auto Mode. Mode Dipswitches Sound Active 1~10 = Off, switch set to Music Auto Mode 1~10 = Off, switch set to Auto 2) The unit will react to the low frequencies of music via the internal microphone in Sound Active mode, or the unit will auto change in
Inhaltszusammenfassung zur Seite Nr. 12
DMX Mode A working DMX-512 signal source plugged into the LEDsplash™ 152B activates the DMX mode. DMX Channel Values NOTE! Please read all instructions carefully on fixture DMX control mode and addressing. DMX channels 2, 3, 4, 5 and 6 functions are determined by the current settings of channel 1. For example, while Channel 1 is set between 000 and 029 the following conditions will apply; Channel 2 will control the Red LEDs Channel 3 will control the Green LEDs Channel 4 will con
Inhaltszusammenfassung zur Seite Nr. 13
111111 111111 222222 222222 444444 444444 888888 888888 16 16 16 16 16 16 16 16 16 16 16 16 32 32 32 32 32 32 32 32 32 32 32 32 64 64 64 64 64 64 64 64 64 64 64 64 128 128 128 128 128 128 128 128 128 128 128 128 256 256 256 256 256 256 256 256 256 256 256 256 SETTING THE DMX STARTING ADDRESS This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start address" from 1 to 512. A fixture requiring one or more channels for control begins to read the data on th
Inhaltszusammenfassung zur Seite Nr. 14
DMX QUICK REFERENCE CHART DMX Address Quick Reference Chart Dip Switch Position DMX DIP #9 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 SWITCH SET 0=OFF #8 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 1=ON #7 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 X=OFF or ON #6 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 #1 #2 #3 #4 #5 0 0 0 0 0 32 64 96 128 160 192 224 256 288 320 352 384 416 448 480 1 0 0 0 0 1 33 65 97 129 161 193 225 257 289 321 353 385 417 449 481 0 1 0 0 0 2 34 66 98 130 162 194 226 258 290 322 354 386 418 450 482
Inhaltszusammenfassung zur Seite Nr. 15
General Troubleshooting Applies to Foggers Dimmers Symptom Solution(s) Lights & Snow Controllers & Chaser Auto shut off Check fan thermal switch reset Beam is very dim or Clean optical system or replace lamp not bright Check 220/110v switch for proper setting Breaker/Fuse keeps Check total load placed on device blowing Chase is too slow Check users manual for speed adjustment Device has no power Check for power on Mains. Check device’s fuse. (intern
Inhaltszusammenfassung zur Seite Nr. 16
Technical Support Address: Service Dept. 3000 N 29th Ct, Hollywood, FL 33020 (U.S.A.) Support (Email): tech@chauvetlighting.com Telephone: (954) 929-1115 - (Press 4) Fax: (954) 929-5560 - (Attention: Service) Website: http://www.chauvetlighting.com 5. APPENDIX DMX Primer There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A fixture capable of receiving DMX 512 will require one or a number of sequential channels. The user must assign a starting a
Inhaltszusammenfassung zur Seite Nr. 17
Returns Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Merchandise Authorization Number (RMA #). Products returned without an RMA # will be refused. Call CHAUVET® and request RA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting fr
Inhaltszusammenfassung zur Seite Nr. 18
Technical Specifications WEIGHT & DIMENSIONS Length .......................................................................................................................... 5.1 in (129 mm) Width............................................................................................................................ 7.5 in (191 mm) Height .......................................................................................................................... 8.1 in (207 mm) Weight......
