Inhaltszusammenfassung zur Seite Nr. 1
HCCA-D600
HCCA-D600
Inhaltszusammenfassung zur Seite Nr. 2
CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Practice Safe Sound™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Record Your Serial Number and Date . . . . . . . . . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 3
INTRODUCTION Thank you for your purchase of Orion's HCCA-D600 power amplifier. Each Orion amplifier is designed to be the leader in its class offering the most power, advanced features, and extreme ease of use. In high-end sound systems or high SPL systems, Orion amplifiers will give you years of trouble-free performance. ● HCCA-D600 - 600 Watt single-channel Class D amplifier with built-in fully variable high-pass, low-pass, or band-pass crossover with INTELLi BASS. Equipped with optional remot
Inhaltszusammenfassung zur Seite Nr. 4
RECORD YOUR SERIAL NUMBER AND DATE To ensure your warranty (see back cover), please record the following information regard- ing your new amplifier. Model: __________________________________________________ Serial Number: __________________________________________________ Date of Purchase: __________________________________________________ Purchased from: __________________________________________________ 3 © 2005 Directed Electronics—all rights reserved
Inhaltszusammenfassung zur Seite Nr. 5
END PANEL LAYOUTS 1 2 345 6 78 9 10 POWER INPUT LINE OUT INTELLI (GREEN) L CH L CH GAIN INFRASONIC LPF REMOTE PHASE BASS MASTER SLAVE ON OFF Oº 180º MIN MAX MIN MAX 30Hz 250Hz PROTECT (RED) R CH R CH 1. RCA Input - accepts RCA input from a head unit, preamplifier, or equalizer. 2. RCA Line Output - provides easy connection to additional amplifiers. 3. Master/Slave Switch - controls whether the amplif
Inhaltszusammenfassung zur Seite Nr. 6
tem battery. WARNING: Always protect this power wire by installing a fuse or circuit breaker of the appropriate size within 12 inches of the battery terminal connection. 3. REM - this terminal turns on the amplifier when (+) 12 volt is applied. Connect it to the remote turn on lead of the head unit or signal source. If a (+) 12 volt remote turn lead is not available, a Remote Power Adapter (P/N #55000) can be used to supply a remote turn on signal. DO NOT connect this terminal to constant (+) 12
Inhaltszusammenfassung zur Seite Nr. 7
SPECIFICATIONS Amplifier Section HCCA-D600 Power Output 4W (Watts) 150 x 1 1 Power Output 2W (Watts) 200 x 1 2 Power Output 1W (Watts) 300 x 1 Amplifier Efficiency > 70% into 1W load at max. power Externally Bridgeable yes Remote Bass Function yes (optional HP-RB1 not supplied) Distortion at Rated Power < 1.0% THD+N Frequency Response 20Hz to 250Hz ±2.5dB Linear Bandwidth 10Hz to 500Hz ±3dB Damping Factor > 200 Input Sensitivity 150mV to 5V rms Supply Voltage Range 9 to 16V thermal, DC offset, r
Inhaltszusammenfassung zur Seite Nr. 8
AMPLIFIER SETTINGS Signal Input and Output Configurations The input section of the amplifier consists of a phase switch that sets the output configura- tion, gain controls, and RCA inputs. The input section makes it easy to adapt this amplifier to most system configurations. Input Gain The Orion HCCA D600 amplifier has a level adjustment to allow for easy integration with any source unit. The input sensitivity can be adjusted from 150mV to 5V. Refer to Testing the System and Adjusting the Sound
Inhaltszusammenfassung zur Seite Nr. 9
WARNING! DO NOT set crossover frequencies lower than the speakers recommended operating range. This can cause driver failure that is not covered by the man- ufacturer's warranty. Low-Pass Crossover The low-pass crossover adjusts the upper crossover of the filter and is continuously variable from 30Hz to 250Hz. Fine Tuning the Crossovers The low-pass and high-pass crossover sections are each marked at four frequency points for ease of system adjustment. The low-pass crossover section is marked at
Inhaltszusammenfassung zur Seite Nr. 10
Infinite Baffle Example High-Pass Set at 30Hz By removing low frequency signal that the woofer cannot produce, the woofer can play its capable range louder. The first example is an infinite baffle situation. The left graph displays the frequency response of a 12-inch woofer in an infinite baffle application without the high-pass filter, with the filter and with the filter and the INTELLi Q set to +3dB. As you can see, with +3dB of boost and the high pass filter set to 30Hz, the woofer has more o
Inhaltszusammenfassung zur Seite Nr. 11
Sealed Example High-Pass Set at 20Hz This sealed example is the same 12-inch woofer in the recommended sealed enclosure. Up to 6 dB of boost is capable if 20 Hz was used. With +6dB of boost, the woofer has more out- put down to 15 Hz. Sealed Example High-Pass Set at 30Hz In this example, the frequency has been increased to 30 Hz. Up to 6 dB of boost is capable at this frequency. With +6dB of boost, the woofer has more output down to 23 Hz. The overall usable output is increased. Vented Example H
Inhaltszusammenfassung zur Seite Nr. 12
Remote Gain Operation NOTE: Do not use the Remote Gain control when you have an expanded system installed (see Line Ouput Configurations). The Slave amplifier(s) gain will not be controlled. The remote gain port provides easy remote access to the internal gain structure of the HCCA power amplifier. The RGC-1 plugs into the amplifier via the 1/8" mini jack plug. The RGC-1 can be installed in the front of the vehicle to control the amplifier gain level. The RGC-1 can be used as a bass level contro
Inhaltszusammenfassung zur Seite Nr. 13
Bridging For bridging into a single speaker load, this amplifier has the ability to be bridged with another amplifier (must be the same model). To do this you must utilize the MASTER/SLAVE and PHASE switch settings. On the master amplifier, set the switch setting to MASTER. The signal is then routed through RCA Line Out to the RCA Line In on the other (slave) amplifi- er. The slave amplifier must have the MASTER/SLAVE switch set to the SLAVE position. On the master amplifier make sure the PHASE
Inhaltszusammenfassung zur Seite Nr. 14
NOTE: The wiring connections to the power, remote and speaker terminals should be accomplished before the amplifier is mounted. NOTE: Mounting amplifiers upside down is not recommended and may cause premature thermal shutdown. WARNING! Do not mount any amplifier in the engine compartment. Amplifiers are not designed to endure the harsh environment of the exterior elements. Passenger Compartment If you are going to mount the amplifier in the passenger compartment, make sure you have adequate room
Inhaltszusammenfassung zur Seite Nr. 15
Orion amplifiers generate a certain amount of heat as part of normal operation. Be sure the area around the amplifier is unobstructed to allow adequate air circulation. Remember, beach blankets, last week's laundry, school books and homework papers located on top of the amplifier do not improve air flow and may become damaged. Tools of the Trade Listed below are the majority of the tools required to perform an installation. Having the proper tools will make the installation that much easier. Som
Inhaltszusammenfassung zur Seite Nr. 16
Controls and Speaker Connections sections of this guide for correct wiring instructions. Step 9 Mount the amplifier. Make sure the amplifier is mounted on a flat surface. If this is not possible, do not over tighten the screws so that the chassis of the amplifier is twisted or bent. Step 10 Reconnect the ground terminal to the battery after power, speaker, and RCA connections are completed. Step 11 Set LPF crossover. Refer to the Internal Crossover Configuration section of this manual for detail
Inhaltszusammenfassung zur Seite Nr. 17
Connections and the Troubleshooting Tips sections of this manual to solve your installation problems. Step 6 Check to make sure the output for each channel is correct. If the active crossovers are used, check to make sure that each output is correct from the amplifier. When using active crossovers on midrange and tweeters, do not use crossover frequencies lower than recommended. If the system is not con- figured properly, refer to the Internal Crossover Configuration section of this manual and t
Inhaltszusammenfassung zur Seite Nr. 18
Troubleshooting Tips Symptom Probable Cause Action To Take No output Low or no remote turn-on Check remote turn-on voltage at voltage amplifier and repair as needed. Fuse blown Check power wire's integrity and check for speaker shorts. Fix as needed and replace fuse. Power wires not connected Check power wire and ground connections and repair or replace as needed. Audio input not connected Check RCA connections and repair or replace as needed. Speaker wires not Check speaker wires and re
Inhaltszusammenfassung zur Seite Nr. 19
Symptom Probable Cause Action To Take Distorted output Internal crossover not set Readjust crossovers. Refer to the properly for speakers Internal Crossover Configuration section of this guide for detailed instructions. Speakers are blown Check system with known work ing speakers and fix or replace as needed. Poor bass response Speakers wired with wrong Check speaker polarity and fix polarity causing cancellation as needed. at low frequencies Crossover set incorrectly Reset crossovers. Refer
Inhaltszusammenfassung zur Seite Nr. 20
NOTES ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ _________________
