Inhaltszusammenfassung zur Seite Nr. 1
F1-FOX
Digital Set-Top Box
for Free-To-Air
User's manual
Remote Control Unit 1~2
Specification
3~4
Support & Copyright
5
Safety 6
STB Connections 7~11
Reference 11
Guide of Functions 12~16
Guide of Main Menu 17~33
Motorised System 34~37
Trouble Shooting Guide 38~39
Menu Tree 40
Inhaltszusammenfassung zur Seite Nr. 2
Remote Control Unit 1. Remote Control Unit (RCU) Information key i Displays the programme information box on the screen and is also used as the RED key in the menus. Soundtrack key Selects the soundtrack list for the current service and is also used as the GREEN key in the menus. Subtitle key Selects the subtitle language list for the current service and is also used as the YELLOW key in the menus. UHF function is not available on this UHF STB but this key is used as the BLUE key in the menus.
Inhaltszusammenfassung zur Seite Nr. 3
Remote Control Unit Standby key P+ / P- Programme Up/Down key Switches between Operation Used to tune to the next or previous and Standby mode. service. Used to move up or down a page in the menu mode. TV/SAT Selects the TV/VCR/SAT mode. Help key ? 09 ~ Numeric key Displays the Help box on the screen. Used to select the service and enter the channel information and PIN Code. Recall key RCL Selects the previously viewed channel. TV/Radio key Receiver Switches: TV/ Radio receive mode EPG Display
Inhaltszusammenfassung zur Seite Nr. 4
Specification 2. STB’S Specification The concept OSD is for On-Screen-Display Tuner & Channel ; means that Menu displays Input Connector : F-type, IEC 169-24, Female on the Screen of TV. Frequency Range : 950 MHz to 2150 MHz Input Impedance : 75Ω unbalanced Signal Level : -25 to -65dBm IF Frequency : 480 MHz IF Band width : 36 MHz LNB Power & Polarisation : Vertical : +13.5V Horizontal : +18V Current : 500mA Max Overload Protection 22 KHz Tone : Frequency : 2
Inhaltszusammenfassung zur Seite Nr. 5
Specification A/V & Data In/Out You can use a special antenna switch TV SCART : Video Output(CVBS, RGB, S-VHS) with DiSEqC commands. Audio Output When changing channel from ASTRA (Resolution : 20bit DAC, max 2 Vrms) to EUTELSAT for example, a DiSEqC VCR SCART : Video Output (CVBS) command is sent with the 22KHz tone : Video Input(CVBS, RGB, S-VHS) through the antenna cable. The antenna switch will change from Audio Output using ASTRA to EUTELSAT. (
Inhaltszusammenfassung zur Seite Nr. 6
Support & Copyright First and foremost, our knowledge of the set-top box marketplace along with technical expertise differentiates Humax. Moreover, we maintain very close working relationships with our customers. We take a highly disciplined engineering approach to product design, manufacture, testing, acceptance, and to technical and maintenance support. We conduct comprehensive testing of the units, provide complete documentation and support, and deliver the highest quality, most consistent
Inhaltszusammenfassung zur Seite Nr. 7
Safety This STB has been manufactured to satisfy the international safety standards. Please read the following recommended safety precautions carefully. MAINS SUPPLY : 190 ~ 250V AC 50/60Hz. OVERLOADING : Do not overload wall outlets, extension cords or adapters as this can result in fire or electrical shock. LIQUIDS : Keep liquids away from the STB. CLEANING : Disconnect the STB from the wall socket before cleaning it. Use a cloth lightly dampened with water (no solvents) to clean
Inhaltszusammenfassung zur Seite Nr. 8
STB Connection There are several ways of connecting the STB to your existing Audio/TV system. We recommend using one of the following set-up for best results: Set-up 1 TV only Connect one end of a 21-pin SCART cable to the TV SCART connector on the STB and the other end to a SCART socket on your TV. Finally connect the coaxial cable from the LNB to the LNB IN socket on the STB. 7
Inhaltszusammenfassung zur Seite Nr. 9
STB Connection Set-up 2 With Hi Fi System Connect an RCA/Cinch stereo cable from the AUDIO L, R sockets on the STB to the LINE, AUX, SPARE OR EXTRA input sockets on your Hi Fi System. 8
Inhaltszusammenfassung zur Seite Nr. 10
STB Connection Set-up 3 TV with VCR Connect one end of a 21-pin SCART cable to the TV SCART connector on the STB and the other end to a SCART socket on your TV. Connect one end of a 21-pin SCART cable to the VCR SCART connector on the STB and the other end to a SCART socket on your VCR. Finally connect the coaxial cable from the LNB to the LNB IN socket on the STB. 9
Inhaltszusammenfassung zur Seite Nr. 11
Inhaltszusammenfassung zur Seite Nr. 12
Reference Set-up 5 TV with VCR and Motorised System with Positioner Connect one end of a 21-pin SCART cable to the TV SCART connector on the STB and the other end to a SCART socket on your TV. Connect one end of a 21-pin SCART cable to the VCR SCART connector on the STB and the other end to a SCART socket on your VCR. Connect the coaxial cable from the LNB of your motorised system to the LNB IN socket on the STB. Connect the motor cables to your positioner (please refer to the manual for your
Inhaltszusammenfassung zur Seite Nr. 13
Inhaltszusammenfassung zur Seite Nr. 14
Guide of Functions Information Box (I-Plate) I-Plate displays when the i key is pressed or when the service is changed. It shows the service part and event part. When you move to another service, the I-Plate should be displayed automatically. The time the I-Plate is displayed on screen is controlled in the Other Setting menu. SERVICE PART The contents of the service part are as follows: - I-Plate Icon, Current Time - Service Name, Service Number and Service Icon - Subtitle( ), Telet
Inhaltszusammenfassung zur Seite Nr. 15
Inhaltszusammenfassung zur Seite Nr. 16
Guide of Functions Subtitle The display of the subtitle are tramitted from the EBU teletext specification and DVB Bitmap. Press the key to bring up the subtitle language list for the current service. Use the / keys to select the desired language. Then press the OK key to select the highlighted language, the subtitles will now be displayed. To cancel the subtitle mode, press the key or EXIT key again. Teletext To view the teletext, you have to use your TV remote control
Inhaltszusammenfassung zur Seite Nr. 17
Guide of Functions In the advanced Service List, it is possible to list All or Favourite service list by using the colour keys as follows: i (red) key - Service List All (green) key - Favourite A. Service All The / keys moves the highlight bar to the previous or next service, using the / keys moves the higlight bar forwards or backwards by 10 services. Select the desired move the cursor service by using the / / / keys. Press the OK key previous or next page to view t
Inhaltszusammenfassung zur Seite Nr. 18
Guide of Main Menu Main Menu The contents of main menu are as follows: move the cursor open the sub menu go to the selected menu exit from the menu screen page 17~19 1. TV GUIDE It shows the programme information and the timer programming process of the service. Select the TV Guide mode by pressing the EPG key in the Video/Audio playback mode. page 19 2. PARENTAL CONTROL It is possible to control access to certain programmes by set- ting the parental level or changing the PIN code. To relea
Inhaltszusammenfassung zur Seite Nr. 19
Guide of Main Menu 1. TV GUIDE You can set the reservation and view the programme (event name) for each service in the TV Guide mode. To access this mode press the EPG key or select the TV Guide in the Main Menu. Change between the TV Guide and Radio Guide by pressing the key. In the TV guide mode, you can select between four different modes. i (red) key - Shows Now or Next programmes for the day. (green) key - Shows programme list for one week. (yellow) key - Shows the Reser
Inhaltszusammenfassung zur Seite Nr. 20
Guide of Main Menu TV GUIDE-Quick mode. This mode shows in the A/V playback mode. The red line represents the current time and shows the programme progress status using a Black/White progress bar. The time range of the bar is made up from the past one hour and the next two hours. 2. PARENTAL CONTROL In the Parental Control Menu, you can set the censorship classification or change the PIN code. Enter the PIN Code 0 0 0 0 . Censorship classification : Set the parental level. If the level disp
