Inhaltszusammenfassung zur Seite Nr. 1
Inhaltszusammenfassung zur Seite Nr. 2
CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Practice Safe Sound™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Limited Two-Year Consumer Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Record Your Serial Num
Inhaltszusammenfassung zur Seite Nr. 3
INTRODUCTION Thank you for your purchase of Orion's 2002 or 3002 amplifier. Each Orion amplifier is designed to be the leader in its class offering ease of use, advanced features, and the most power. Orion amplifiers are designed as the best affordable high end car audio amplifier money can buy. Listed below are the features of the new Orion 2002 and 3002. ● 2002 - 50 Watts per channel, two-channel amplifier with dual built-in high-pass and low-pass 12dB/octave crossover centered at 100Hz and IN
Inhaltszusammenfassung zur Seite Nr. 4
LIMITED TWO-YEAR CONSUMER WARRANTY Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be defective in workmanship or material under normal use, for a period of two years from the date of purchase by the dealer as indicated by the date code marking of the product PROVIDED the product was installed by an authorized Directed dealer. During this two year period, there will be no charge for this replacement PROVIDED the unit is returned to Direct
Inhaltszusammenfassung zur Seite Nr. 5
SPECIFICATIONS Amplifier Section Orion 2002 Orion 3002 1 Power Output 4W Stereo (Watts) 50 x 2 75 x 2 2 Power Output 2W Stereo (Watts) 100 x 2 150 x 2 1 Power Output 4W Mono (Watts) 200 x 1 300 x 1 Distortion - all channels < 0.1% THD+N < 0.1% THD+N driven at rated power (20Hz to 20kHz) Frequency Response 20Hz to 20kHZ 20Hz to 20kHZ ±0.25dB ±0.25dB Linear Bandwidth 10Hz to 50kHz ±3dB 10Hz to 50kHz ±3dB Signal-to-Noise Ratio > 100dB > 100dB at Rated Power Damping factor > 200 > 200 Slew Rate >
Inhaltszusammenfassung zur Seite Nr. 6
5 ©2004 Directed Electronics, Inc.
Inhaltszusammenfassung zur Seite Nr. 7
AMPLIFIER CONTROLS AND CONNECTIONS 2 1 34 5678 9 12 11 10 1. Power LED - when lit indicates that the amplifier is on. 2. Stereo/Mono Switch - configures the amplifier for one or two inputs. 3. High-Level Input Connector - accepts input from head unit's speaker output. 4. RCA Inputs - accepts RCA input from a source unit, preamplifier, or equalizer. 5. Gain Control - continuously adjusts from 200mV to 5V for full power output. 6. Frequency Control - adjusts the frequency of the crossover. 7. Cros
Inhaltszusammenfassung zur Seite Nr. 8
AMPLIFIER SETTINGS Stereo / Mono Input Configuration The STEREO / MONO switch allows the Orion 2002 and 3002 amplifiers to use a single RCA or high-level input to feed signal to both the right and left channels of the amplifier. When the switch is to the right (MONO position), signal from the left input is routed to the right channel. This is the preferred mode when bridging the amplifier into a single speak- er. When the switch is to the left (STEREO position), right and left inputs are indepen
Inhaltszusammenfassung zur Seite Nr. 9
High-Pass Crossover When the switch is to the left (FULL position), the high-pass crossover is bypassed. When the switch is in the middle (HIGH position), the high-pass crossover is active. The high-pass crossover is continuously variable from 20Hz to 3kHz. Input Gain The Orion 2002 and 3002 amplifiers have gain adjustments with an input sensitivity range from 200mV up to 5V on the RCA inputs and 1V to 10 on the high-level inputs. This allows easy integration from any source unit either with RCA
Inhaltszusammenfassung zur Seite Nr. 10
AMPLIFIER WIRING Power Connections ● Orion 2002 Fuse Size: (1) 25 AMP ● Orion 3002 Fuse Size: (1) 30 AMP ● Minimum 8 AWG power and ground cable is recommended for acceptable per- formance. ● Fuse power wire prior to wire passing through panels or near sharp edges and less than 18" from battery. ● Ground amplifier to a good chassis ground as close as possible to the amplifier. ● Add extra ground wire (minimum 8 AWG) between the negative terminal of the battery and the chassis. NOTE: The addition
Inhaltszusammenfassung zur Seite Nr. 11
Summed Bridged Configuration ● Lowest recommended impedance is 4W bridged mono. ● Mono or stereo input can be used for this configuration. ● Outputs can be configured for high-pass, low-pass, or full range operation. ● Output is configured as summed bridged which is ideal for subwoofer applications. Single Channel Bridged Configuration ● Lowest recommended impedance is 4W mono. ● Mono input must be used for this configuration. Only the Left input is used. ● Outputs can be configured for high-pas
Inhaltszusammenfassung zur Seite Nr. 12
Tri-Mode Three Channel Configuration ● Lowest recommended impedance is 2W stereo and 4W bridged mono. ● Stereo operation must be used. ● Outputs must be configured for full range operation ● Output is configured stereo and summed bridged. ● Passive crossover frequencies must not overlap. WARNING! Failure to observe these requirements may result in damage to the amplifier. AMPLIFIER INSTALLATION Choosing Mounting Locations The location of your amplifier will depend on several important issues. Du
Inhaltszusammenfassung zur Seite Nr. 13
amplifier with as much clearance as possible. This type of mounting will yield the best cool- ing due to the convection effect of the amplifier chassis. General Precautions and Installation Tips WARNING! Be careful not to cut or drill into gas tanks, fuel lines, brake lines, hydraulic lines, vacuum lines, or electrical wiring when working on your vehicle. Disconnect the vehicle's ground wire at the battery before making or breaking connections to the audio system's power supply terminals. Do not
Inhaltszusammenfassung zur Seite Nr. 14
● Pliers (standard and needle nose) ● Reference CD with 1 kHz Sine Wave at 0dB level (all bits high) ● RTA (real time analyzer) ● Soldering iron and solder ● Utility knife ● Wire brush or sandpaper for chassis grounding ● Wire crimper ● Wire cutters ● Wire strippers Step By Step Installation Step 1 Determine the location for the amplifier. Refer to the Choosing Mounting Locations section of this guide for detailed information. Step 2 Decide on the system configuration for your amplifier. For sys
Inhaltszusammenfassung zur Seite Nr. 15
SET UP AND TROUBLESHOOTING Testing the System After you have completed the installation, you need to test the system. This will help ensure years of trouble-free operation. Please refer to the listed steps below when testing the sound of your Orion system. Step 1 Check all the wiring connections to be sure they are correct and secure. Step 2 Turn the signal source volume control all the way down. Set any tone con- trols to their flat or defeated positions. This includes the loudness control. Ste
Inhaltszusammenfassung zur Seite Nr. 16
Step 6 Turn up the level control corresponding to the tweeter output until you hear slight distortion and turn back the level control slightly for an undistorted output. Depending on your system the midrange and tweeter output may be on the same output channels. Step 7 Fine-tune the output level between midrange and tweeters. Refer to the Internal Crossover Configuration section of this manual for detailed instruc- tions. Step 8 Repeat Steps 5-7 for the rear speakers. If you do not have rear spe
Inhaltszusammenfassung zur Seite Nr. 17
Troubleshooting Tips Symptom Probable Cause Action To Take No output Low or no remote turn-on Check remote turn-on voltage at voltage amplifier and repair as needed. Fuse blown Check power wire's integrity and check for speaker shorts. Fix as needed and replace fuse. Power wires not connected Check power wire and ground connections and repair or replace as needed. Audio input not connected Check RCA connections and repair or replace as needed. Speaker wires not Check speaker wires and re
Inhaltszusammenfassung zur Seite Nr. 18
Symptom Probable Cause Action To Take Distorted output Internal crossover not set Readjust crossovers. Refer to the properly for speakers Internal Crossover Configuration section of this guide for detailed instructions. Speakers are blown Check system with known work ing speakers and fix or replace as needed. Poor bass response Speakers wired with wrong Check speaker polarity and fix polarity causing cancellation as needed. at low frequencies Crossover set incorrectly Reset crossovers. Refer
Inhaltszusammenfassung zur Seite Nr. 19
Warranty LIMITED TWO YEAR CONSUMER WARRANTY: Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be defective in workmanship or material under normal use, for a period of two years from the date of purchase by the dealer as indicated by the date code marking of the product PROVIDED the product was installed by an authorized Directed dealer. During this two year period, there will be no charge for this replacement PROVIDED the unit is returned
