Inhaltszusammenfassung zur Seite Nr. 1
INSTALLATION INSTRUCTIONS
HD44CC5 HD44C
High Definition Video Matrix Switcher, High Definition Video Matrix Switcher,
Coaxial and CAT5 Coaxial Only
DESCRIPTION
The HD44CC5 four-source, four-zone high-definition matrix switcher has component video and
S/PDIF digital audio inputs for each source. All four zone outputs have component video output and
S/PDIF audio output for economical local distribution up to 250’, as well as a RJ45 output for
transmission of the video and digital
Inhaltszusammenfassung zur Seite Nr. 2
DETAIL OVERVIEW [1] SOURCE LOOP-THROUGH CONNECTION The source inputs are buffered to provide an output at the same levels, assuming a 75-ohm termination is on the output. Use these connections for HD44 expansion systems. The buffers are an active circuit. The HD44 must be powered on for an active connection. [2] SOURCE INPUTS Gold-plated RCA jacks for connection from the output of the source. Color coordinated to match all HD source components. 08905071B - 2 -
Inhaltszusammenfassung zur Seite Nr. 3
[3] IR RECEIVER The rear panel IR receiver is a 3.5mm Stereo jack that is compatible with all Xantech IR receivers, such as the 291-10. Switch 4 must be in the OFF position to use this jack. PLUG CIRCUIT TIP IR SIGNAL RING GROUND SLEEVE +12VDC, 25mA [4] IR BUS, EMITTER PORT The 3.5mm Mono jack is an emitter port. The IR signal is connected to the IR Receiver. A Xantech 283M emitter can be connected to this port. PLUG 2-Pin WECO CIRCUIT TIP + IR SIGNAL SLEEVE - GROUND
Inhaltszusammenfassung zur Seite Nr. 4
RS232 COMMAND STRUCTURE Where: {CR#} – Carriage Return (0x0D) {z#} - Zone Number. Range is 1..4 (1..16 if expanded) {s#} - Source Input Number. Range is 1..4 {0/1} – Either 0 (zero) or 1 (one). 0 – Off, 1 – On. REMARKS NAME COMMAND RETURN To turn on Zone 2: !2PR1+ or !02PR1+ or !{z#}PR01+ OK{CR} !2PR01+ or !02PR01+ Zone Power ERROR{CR} To turn off Zone1: !1PR0+ or !01PR0+ or !{z#}PR00+ !1PR00+ or !01PR00+ Zone Power OK{CR} !{z#}PT+ Toggle ERROR{CR} OK{C
Inhaltszusammenfassung zur Seite Nr. 5
RS232 QUERIES Where: {CR#} – Carriage Return (0x0D) {z#} - Zone Number. Range is 1..4 (1..16 if expanded) {s#} - Source Input Number. Range is 1..4 {0/1} – Either 0 (zero) or 1 (one). 0 – Off, 1 – On. EXAMPLE NAME QUERY RETURN EXPLANATION RETURN Zone Power ?{z#}PR+ ?{z#}PR{0/1}+ ?4PR0+{CR} Power in zone 4 is OFF. Input Select ?{z#}SS+ ?{z#}SS{s#}+ ?4SS3+{CR} Zone 4 currently has source 3 selected. ?SI ?SI Device: {Device: HD44, Devic
Inhaltszusammenfassung zur Seite Nr. 6
[6] AC POWER INPUT Standard IEC 3-Conductor AC Line Cord Receptacle for plug-in of a 3-conducator power line cord. Be sure to note if the power receptacle is domestic (120VAC type) or international (240VAC type). [7] RS232 EXPANSION The HD44C and HD44CC5 can be expanded into a larger system. By using any combination of the HD44C and HD44CC5 (up to 4 units), a larger High-Definition distribution system can be created. For instance, two HD44C units can be combined to create a much la
Inhaltszusammenfassung zur Seite Nr. 7
[9] CAT5 ZONE OUTPUT Output connection to the HDRXSG01 receiver module. Uses standard CAT5 cable. Be sure to verify CAT5 wiring connection is correct before installation. [10] COAXIAL ZONE OUTPUT Gold-plated RCA jacks for connection to an HD monitor. Color coordinated to match all HD type products. The CAT5 and coaxial output can be used at the same time. IMPORTANT NOTICE After connecting the CAT5 cable to the receiver (HDRXSG01), the power supply to the receiver should b
Inhaltszusammenfassung zur Seite Nr. 8
QUICK INSTALLATION: HD44CC5 and HDRXSG01 [1] Connect the High-Definition Source to the HD44CC5 or HDTXSG01. Figure 1 below shows a HD44CC5 (video matrix transmitter) connected to the HDRXSG01 (receiver). [2] Using CAT5 cable, connect the HD44CC5 zone output or the output from the HDTXSG01 to the HDRXSG01. Connect power to the HD44CC5 first. Then connect power to the HDRXSG01. [3] On the HD44CC5, set the source to zone to enable the HDRXSG01 from the connected High- Definition source.
Inhaltszusammenfassung zur Seite Nr. 9
RC68+ (IR) COMMANDS The RC68+ should be set to Group Code “C0”. ZONE 1 ZONE 2 ZONE 3 ZONE 4 Zone Power Toggle 80 48 10 90 1 SRC 1 SRC 2 SRC 3 SRC 4 Zone 1 Source Select 00 C0 50 D0 Zone 2 Source Select 40 A0 30 B0 2 Zone 3 Source Select 20 E0 70 F0 Zone 4 Source Select 60 88 18 98 ZONE 1 ZONE 2 ZONE 3 ZONE 4 Zone Power On 08 A8 38 B8 3 Zone Power Off 28 E8 78 F8 4 5 Zone Power All Off 68 Zone Restore All C8 6 Zone Power All On 58 7 Note: For e
Inhaltszusammenfassung zur Seite Nr. 10
ADVANCE INSTALLATION FIGURE 2: Below shows a diagram for a sports bar application. With the equipment rack located near or behind the bar area, the coaxial outputs can be used for local HD monitors. The CAT5 outputs can be used to deliver HD content to areas such as outdoor patios and pool table recreational areas. FIGURE 2 FIGURE 3: The figure in the next page shows an expanded HD44CC5 system. With two HD44CC5 devices, HD content can be distributed to 16 displays (8 with CA
Inhaltszusammenfassung zur Seite Nr. 11
FIGURE 3 (Note: The top unit (master unit) must be addressed as UNIT #1) 08905071B - 11 -
Inhaltszusammenfassung zur Seite Nr. 12
COMMON PROBLEMS AND TROUBLESHOOTING Poor video quality (picture is washed out): Several manufacturers of cable and satellite box may have higher than normal DC offset on the video signals. When connected to an HD44C, HD44CC5, and HDTXSG01, this may result in a washed out picture. To remedy this problem, a DC blocker should be used between the source component and the HD44C, HD44CC5, and HDTXSG01. Picture appears to be blooming: A blooming picture is usually caused by a video sign
Inhaltszusammenfassung zur Seite Nr. 13
This page intentionally left blank 08905071B - 13 -
Inhaltszusammenfassung zur Seite Nr. 14
This page intentionally left blank 08905071B - 13 -
Inhaltszusammenfassung zur Seite Nr. 15
This page intentionally left blank 08905071B - 13 -
Inhaltszusammenfassung zur Seite Nr. 16
Xantech Limited Warranty (Effective for products sold after July 1, 2006) Xantech Corporation (“Xantech”) warrants to the holder of a valid proof of purchase as the first end-user purchaser (“You”), its products to be free from defects in materials and workmanship for the periods specified below from the date of purchase. This limited warranty extends only to You for product purchased and used in the United States of America. For product purchased outside of the United States of America,
