Inhaltszusammenfassung zur Seite Nr. 1
4/8 ports 10/100/1000Mbps
Gigabit Ethernet Desktop Switch Layer 2
USER’S GUIDE
Inhaltszusammenfassung zur Seite Nr. 2
The Atlantis Land logo is a registered trademark of Atlants Land SpA. All other names mentioned mat be trademarks or registered trademarks of their respective owners. Subject to change without notice. No liability for technical errors and/or omissions. FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferenc
Inhaltszusammenfassung zur Seite Nr. 3
T C ABLE OF ONTENTS ABOUT THIS GUIDE ....................................................... 1 TERMS .............................................................................................. 1 OVERVIEW OF THIS USER’S GUIDE ................................................... 1 INTRODUCTION................................................................. 2 G E T ................................................... 2 IGABIT THERNET ECHNOLOGY FAST ETHERNET TECHNOLOGY...................
Inhaltszusammenfassung zur Seite Nr. 4
ABOUT THIS GUIDE This user’s guide tells you how to install your 4(8)-port 10/100/1000Mbps Gigabit Ethernet Switch, how to connect it to your Gigabit Ethernet network. Terms For simplicity, this documentation uses the terms “Switch” (first letter upper case) to refer to the 4(8)-port 10/100/1000Mbps Gigabit Ethernet Switch, and “switch” (first letter lower case) to refer to all Ethernet switches, including the 4(8)-port 10/100/1000Mbps Gigabit Ethernet Switch. Overview of this User’s
Inhaltszusammenfassung zur Seite Nr. 5
INTRODUCTION This section describes the features of the 4(8)-port 10/100/1000Mbps Gigabit Ethernet Switch, as well as giving some background information about Gigabit Ethernet, Fast Ethernet and Switching technology. Gigabit Ethernet Technology Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the same packet structure, format, and support for CSMA/CD protocol, full duplex, flow control, and management objects, but with a tenfold increase in theoretical throughput over
Inhaltszusammenfassung zur Seite Nr. 6
to perform 10 times the number of operations in the same amount of time. In addition, the phenomenal bandwidth delivered by Gigabit Ethernet is the most cost-effective method to take advantage of today and tomorrow’s rapidly improving switching and routing internetworking technologies. And with expected advances in the coming years in silicon technology and digital signal processing that will enable Gigabit Ethernet to eventually operate over unshielded twisted-pair (UTP) cabling, outf
Inhaltszusammenfassung zur Seite Nr. 7
environments, it provides a straightforward upgrade and takes advantage of the existing investment in hardware, software, and personnel training. Switching Technology Another key development pushing the limits of Ethernet technology is in the field of switching technology. A switch bridges Ethernet packets at the MAC address level of the Ethernet protocol transmitting among connected Ethernet or fast Ethernet LAN segments. Switching is a cost-effective way of increasing the total netwo
Inhaltszusammenfassung zur Seite Nr. 8
Features The 4(8)-port 10/100/1000Mbps Gigabit Ethernet Switch was designed for easy installation and high performance in an environment where traffic on the network and the number of users increase continuously. Switch features include: Ports ♦ 4(8) 10/100/1000Mbps Gigabit Ethernet port Performance features ♦ Auto MDI/MDI-X for each port ♦ Support Full/Half duplex transfer mode for 10 and 100Mbps ♦ Support Full duplex transfer mode for 1000Mbps ♦ Wire speed reception and transmis
Inhaltszusammenfassung zur Seite Nr. 9
UNPACKING AND SETUP This chapter provides unpacking and setup information for the Switch. Unpacking Open the shipping carton of the Switch and carefully unpack its contents. The carton should contain the following items: ♦ One 4(8)-port 10/100/1000Mbps Gigabit Ethernet Switch ♦ Four rubber feet with adhesive backing ♦ One AC power cord ♦ This User’s Guide (CD-Rom) If any item is found missing or damaged, please contact your local reseller for replacement. Setup The setup of the S
Inhaltszusammenfassung zur Seite Nr. 10
♦ Make sure that there is proper heat dissipation from and adequate ventilation around the Switch. Do not place heavy objects on the Switch. Desktop or Shelf Installation When installing the Switch on a desktop or shelf, the rubber feet included with the device must be first attached. Attach these cushioning feet on the bottom at each corner of the device. Allow enough ventilation space between the device and the objects around it. Gigabit Ethernet Switch installed on a Desktop or
Inhaltszusammenfassung zur Seite Nr. 11
mounting brackets on the switch’s front panel (one on each side) and secure them with the screws provided. Attaching the mounting brackets to the Switch Then, use the screws provided with the equipment rack to mount the Switch in the rack. Installing the Switch in an equipment rack Connecting Network Cable The 4(8)-Port 10/100/1000Mbps Gigabit Ethernet Switch supports four or eight 10/100/1000Mbps Gigabit Ethernet ports. These ports runs both half duplex and full duplex while they
Inhaltszusammenfassung zur Seite Nr. 12
These ports are Auto-MDI type port, these ports can auto transform to MDI-II or MDI-X type, so you can just make an easy connection that without worrying if you are using a standard or crossover cable. Power on The 4(8)-port Gigabit Ethernet Switch can be used with AC power sources 100~240V AC, 50~60 Hz. The power supply of the Switch will adjust to the local power source automatically and may be turned on without having any or all LAN segment cables connected. IDENTIF
Inhaltszusammenfassung zur Seite Nr. 13
Front Panel The front panel of the Switch consists of 4(8) Gigabit Ethernet port, and LED indicators. LED Indicators 1000BASE-T Gigabit Ethernet Ports Front panel view of the 4-port 10/100/1000Mbps Gigabit Ethernet Switch ♦ Four(Eight) 10/100/1000Mbps Gigabit Ethernet ports ♦ Comprehensive LED indicators that display the conditions of the Switch and status of the network. A description of these LED indicators follows (see LED Indicators). Rear Panel The rear panel of the Swit
Inhaltszusammenfassung zur Seite Nr. 14
♦ AC Power Connector This is a three-pronged connector that supports the power cord. Plug in the female connector of the provided power cord into this connector, and the male into a power outlet. Supported input voltages range from 100 ~ 240 V AC at 50 ~ 60 Hz. LED Indicators The LED indicators of the Switch include Power, Link/Act, 1000Mbps and 100Mbps. The following shows the LED indicators for the Switch along with an explanation of each indicator. The 4-port 10/100/1000Mbps
Inhaltszusammenfassung zur Seite Nr. 15
♦ 1000Mbps : These LED indicators are lighted up when there is a secure connection (or link) to 1000Mbps Gigabit Ethernet device at the desired port. 100Mbps: ♦ These LED indicators are lighted up when there is a secure connection (or link) to 100Mbps Fast Ethernet device at the desired port. When the connection (or link) is 10Mbps, both 1000Mbps and 100Mbps LED indicators are off. Product Support If you continue to have problems you should contact the dealer where you bought
Inhaltszusammenfassung zur Seite Nr. 16
TECHNICAL SPECIFICATIONS General IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet Standards: IEEE 802.3ab 1000BASE-T Gigabit Ethernet ANSI/IEEE 802.3 Auto-negotiation IEEE 802.3x Full duplex Flow Control Protocol: CSMA/CD Ethernet: 10Mbps (half-duplex), 20Mbps (full-duplex) Data Transfer Fast Ethernet: 100Mbps (half-duplex), 200Mbps (full-duplex) Rate: Gigabit Ethernet: 2000 Mbps (full-duplex) Topology Star Ethernet: 2-pair UTP Cat. 3/4/5 Network Fast Ethernet:
Inhaltszusammenfassung zur Seite Nr. 17
Physical and Environmental AC inputs: 100 – 240 VAC, 50/60 Hz Power 12 watts max(4 ports), 20 watts max (8 ports) Consumption: Operating 0 ~ 40 degrees Celsius Temperature: Storage -10 ~ 55 degree Celsius Temperature: Humidity: 5% ~ 95% RH, non-condensing Dimensions: 280 mm x 180 mm x 44 mm EMI: FCC Class A, CE Mark Class A, VCCI-A Safety: UL (UL 1950), TUV/GS (EN60950) Performance Transmission Store-and-forward Method: RAM Buffer: 256K bytes per device Filtering Address
