Inhaltszusammenfassung zur Seite Nr. 1
Operator’s manual (EPA)
Please read the operator’s manual carefully and
make sure you understand the instructions
before using the machine.
BC 2125
Inhaltszusammenfassung zur Seite Nr. 2
15 m 50FT KEY TO SYMBOLS Symbols Only use non-metallic, flexible cutting WARNING! Clearing saws, brushcutters attachments, i.e. trimmer heads with and trimmers can be dangerous! Careless trimmer cord. or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator’s manual. Other symbols/decals on the machine refer to special certific
Inhaltszusammenfassung zur Seite Nr. 3
CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Please read the operator’s manual carefully. Symbols ....................................................................... 2 Maintenance, replacement, or repair of the emission control CONTENTS devices and system may be performed by any nonroad Contents ...................................................................... 3 engine repair establishment or indivi
Inhaltszusammenfassung zur Seite Nr. 4
INTRODUCTION Dear customer! Congratulations on your choice to buy a Jonsered product! Your purchase gives you access to professional help with repairs and service whenever this may be necessary. If the retailer who sells your machine is not one of our authorized dealers, ask for the address of your nearest servicing dealer. It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this operator′s manual as a valuable
Inhaltszusammenfassung zur Seite Nr. 5
WHAT IS WHAT? 30 17 31 18 19 20 22 JONSERED SER VICE 24 21 21 4 4 28 23 25 27 26 What is what? 1 Blade 17 Handle adjustment 2 Grease filler cap, bevel gear 18 Locking nut 3 Bevel gear 19 Support flange 4 Cutting attachment guard 20 Support cup 5 Shaft 21 Drive disc 6 Handlebar 22 Trimmer head 7 Throttle control 23 Socket spanner 8 Stop switch 24 Operator’s manual 9 Throttle lockout 25 Transport guard 10 Support eyes for harness 26 Allen key 11 Cylinder cover 27 Locking pin 12 Starter ha
Inhaltszusammenfassung zur Seite Nr. 6
SAFETY INSTRUCTIONS Important Personal protective equipment IMPORTANT! IMPORTANT! The machine is only designed for trimming grass, grass A clearing saw, brushcutter or trimmer can be dangerous if clearing and/or forestry clearing. used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely The only accessories you can operate with this engine unit important that you read and understand the contents of this are the cut
Inhaltszusammenfassung zur Seite Nr. 7
SAFETY INSTRUCTIONS CLOTHING Make sure the throttle control is locked at the idle setting when the throttle lockout is released. Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure hair so it is above shoulder level. FIRST AID KIT Always have a first aid kit nearby. Press the throttle lockout and make sure it returns to its o
Inhaltszusammenfassung zur Seite Nr. 8
SAFETY INSTRUCTIONS Regularly check the vibration damping units for cracks or Cutting attachment guard deformation. Check that the vibration damping element is undamaged and securely attached. WARNING! Overexposure to vibration can This guard is intended to prevent loose objects from being lead to circulatory damage or nerve damage thrown towards the operator. The guard also protects the ! in people who have impaired circulation. operator from accidental contact with the cutting att
Inhaltszusammenfassung zur Seite Nr. 9
SAFETY INSTRUCTIONS Never use a machine that has a faulty muffler. Locking nut A locking nut is used to secure some types of cutting attachment. Regularly check that the muffler is securely attached to the machine. When fitting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. To remove it, If the muffler on your machine is fitted with a spark arrestor undo the nut in the same direction as the cutting attachment screen this must be cleaned regula
Inhaltszusammenfassung zur Seite Nr. 10
SAFETY INSTRUCTIONS General rules Cutting equipment This section describes how to choose and maintain your cutting equipment in order to: Only use cutting attachments with the guards we • Reduce the risk of blade thrust. recommend! See the chapter on Technical data. • Obtain maximum cutting performance. • Extend the life of cutting equipment. IMPORTANT! Keep the teeth of the blade correctly sharpened! Follow our Only use cutting attachments with the guards we instructions and use the recomme
Inhaltszusammenfassung zur Seite Nr. 11
SAFETY INSTRUCTIONS Sharpening the saw blade Trimmer head IMPORTANT! Always ensure the trimmer cord is wound tightly and evenly • See the cutting attachment packaging for correct around the drum, otherwise the machine will generate sharpening instructions. harmful vibration. A correctly sharpened blade is essential for working efficiently • Only use the recommended trimmer heads and trimmer and to avoid unnecessary wear to the blade and clearing saw. cords. These have been tested by the manu
Inhaltszusammenfassung zur Seite Nr. 12
ASSEMBLY Assembling the handlebar and Assembling the handlebar and throttle throttle (turnable handlebar) • Remove the screw at the rear of the throttle handle. • Remove the screw at the rear of the throttle handle. • Slide the throttle handle onto the right side of the • Slide the throttle handle onto the right side of the handlebar, (see diagram). handlebar, (see diagram). • Align the screw hole in the throttle handle with the hole in • Align the screw hole in the throttle handle with the
Inhaltszusammenfassung zur Seite Nr. 13
ASSEMBLY Transport position, handlebar Fitting a blade guard, grass blade and grass cutter • The handlebar can easily be turned to fit along the shaft for easier transportation and storage. G • Loosen the knob. Turn the handlebar clockwise so that the F throttle handle rests against the engine. E • Now twist the handlebar around the shaft. Tighten the D knob. B A C • Fit the transport guard to the cutting attachment. • Hook the blade guard/combination guard (A) onto the Assembling the cutting
Inhaltszusammenfassung zur Seite Nr. 14
ASSEMBLY arrow in the diagram shows the area where you should Fitting the blade guard and saw operate the socket spanner when loosening or tightening blade the nut. K J Fitting the trimmer guard and Auto H I 32 trimmer head A L K L • Remove the mounting plate (H). Fit the adapter (I) and G bracket (J) with the two screws (K) as shown. Fit the blade K F B I guard (A) to the adapter using the 4 screws (L) as shown. C J I CAUTION! Use the recommended blade guard. See the Technical data secti
Inhaltszusammenfassung zur Seite Nr. 15
ASSEMBLY • Fit the bottom half of the trimmer head (K) to the cover (I) Standard harness by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover. Quick release At the front is an easily accessible, quick release. Use this if the engine catches fire or in any other emergency situation that requires you to free yourself from the machine and • To dismantle, follow the instructions in the reverse order. harness. Fitting other guards and cutting atta
Inhaltszusammenfassung zur Seite Nr. 16
FUEL HANDLING Gasoline Fuel safety Never start the machine: 1 If you have spilled fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. CAUTION! Always use a quality gasoline/oil mixture with an octane rating of at least 87 octane ((RON+MON)/2). If your 2 If you have spilled fuel on yourself or your clothes, change machine is equipped with a catalytic converter (see chapter your clothes. Wash any part of your body that has come in on Technical data) always use a good qua
Inhaltszusammenfassung zur Seite Nr. 17
FUEL HANDLING Mixing Fueling • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. WARNING! Taking the following precautions, will lessen the risk of fire: • Mix (shake) the fuel mixture thoroughly before filling the ! machine’s fuel tank. Do not smoke or place hot objects near fuel. Always shut off the
Inhaltszusammenfassung zur Seite Nr. 18
STARTING AND STOPPING Check before starting Starting and stopping • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most WARNING! The complete clutch cover and common reason why cracks are formed is that sharp shaft must be fitted before the machine is ! corners have been formed at the bottom of the teeth while started, otherwise the clutch can come loose sharpening or that the blade has been used with dull and cause personal inju
Inhaltszusammenfassung zur Seite Nr. 19
STARTING AND STOPPING CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. CAUTION! Do not put any part of your body in marked area. Contact can result in burns to the skin, or electrical shock if the spark plug cap has been damaged. Always use gloves. Do not use a machine with damaged spark plug cap. For throttle handles with a start throttle lock: Set the throttle to the start positio
Inhaltszusammenfassung zur Seite Nr. 20
WORKING TECHNIQUES 6 Keep a good balance and a firm foothold. General working instructions 7 Always hold the machine with both hands. Hold the machine on the right side of your body. IMPORTANT! This section describes the basic safety precautions for working with clearing saws and trimmers. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. Avoid all usage which you consider to be beyond your capability.
