Inhaltszusammenfassung zur Seite Nr. 1
RFX9110
RFX9110G
RFX9110R
Installation &
RFX9210
Operation
RFX9210G
RFX9210R
Source Units
Installation et fonctionnement
Instalación y funcionamiento
Inhaltszusammenfassung zur Seite Nr. 2
INTRODUCTION Dear Customer, Congratulations on your purchase of the world’s finest brand of car audio source units. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve. For maximum performance we recommend you have your new Rockford F
Inhaltszusammenfassung zur Seite Nr. 3
GETTING STARTED Welcome to Rockford Fosgate! This manual is designed to provide information for the owner, salesperson and installer. For those of you who want quick information on how to install this product, please turn to the Installation Section of this manual. Other information can be located by using the Table of Contents. We, at Rockford Fosgate, have worked very hard to make sure all the information in this manual is current. But, as we are constantly finding new ways to improve our pro
Inhaltszusammenfassung zur Seite Nr. 4
e l l l g g g n n n u u u j j j e e e h h h t t t f f f o o o s s s d d d n n n u u u o o o s s s s s s u u u o o o LIQUID SWORD INC. i i i c c c i i i v v v • • • PRECAUTIONS Handling the Detachable Faceplate DO NOT drop or cause shock to the faceplate as serious damage may occur. Protect the faceplate by storing it in the supplied carrying case. Avoid Mechanical Malfunction DO NOT grab a disc while it is being automatically loaded into the source unit. Doing this may cause serious damage to
Inhaltszusammenfassung zur Seite Nr. 5
INSTALLATION INSTALLATION CONSIDERATIONS The following is a list of tools needed for installation: Volt/Ohm Meter Hand held drill w/assorted bits Wire strippers 1/8" diameter heatshrink tubing Wire crimpers Assorted connectors Wire cutters Soldering iron #2 Phillips screwdriver Solder Battery post wrench Heat gun This section focuses on some of the vehicle considerations for installing your new Source Unit. Pre- planning your system layout and best wiring routes will save installation time. When
Inhaltszusammenfassung zur Seite Nr. 6
INSTALLATION Center Console Mounting the source unit in the center console provides optimum access. Be sure the installation does not interfere with the operation of the gear shift or parking brake. The source unit should have a mounting angle within ±20° from horizontal. Glove Box Mounting the source unit in the glove box is adequate, but does not provide easy access. Glove box mounting should only be done if “Instrument Panel” or ”Center Console,” mounting is not acceptable (i.e., maintaining
Inhaltszusammenfassung zur Seite Nr. 7
Horizontal -20° +20° INSTALLATION Connect the Speaker Wires (if external amplifiers are not used) to the corresponding speaker leads by soldering and heat shrinking all connections for a reliable installation. If only one pair of speakers is utilized in the system, use only the FRONT speaker leads and heat shrink the unused REAR leads to prevent from shorting out. Be sure to maintain speaker polarity. DO NOT chassis ground any speaker leads as unstable operation may result. 11. Install the Pream
Inhaltszusammenfassung zur Seite Nr. 8
SOURCE UNIT FEATURES 1. OFF (PWR-Remote)– Turns the source unit on and off. 2. BAND – Selects which bank of tuner presets (FM1/FM2/AM) should be active. 3. MODE – Selects between TUNER/CDP/CDX/AUX1* modes. 4. UP – Selects the next radio station in TUNER mode and selects the next track in CDP/CDX mode. 5. OPEN – Opens the faceplate and ejects CDs from the in-dash CD player. 6. DOWN – Selects the previous radio station in TUNER mode and selects the previous track in CDP/CDX mode. 7. LOC – Selects
Inhaltszusammenfassung zur Seite Nr. 9
SOURCE UNIT FEATURES IR Remote Special Features 23. SEEK/TRACK / – Selects the next/previous radio station in TUNER mode and selects the next/previous track in CDP/CDX mode. 24. VOL / – Controls VOLUME, BASS, TREBLE, BALANCE, FADER, and SUM*. 25. SEL – Selects between VOLUME, BASS, TREBLE, BALANCE, FADER, and SUM* modes. 26. DIR – Cycles up and down through the directory in MP3 mode. 27 PTY – Allows priority broadcasts to interrupt all other functions in international units only. 28. AF/TP – A
Inhaltszusammenfassung zur Seite Nr. 10
OPERATION – BASIC RESET BUTTON CAUTION: Do not press the Reset Button too hard or you may cause damage that ! may void your warranty. If you need assistance, please consult an Authorized Rockford Fosgate Dealer. 1. Follow the instructions above to detach the faceplate. 2. Insert a paper clip or other slender object into the Reset Button hole in the lower left corner of the unit and gently press it in until the button clicks. Remote POWER ON/OFF 1. Press the OFF (PWR) button to turn the radio on.
Inhaltszusammenfassung zur Seite Nr. 11
OPERATION – BASIC • P. PLAY [EJ MUTE] — Plays the Tuner after you eject a CD while Eject Mute mutes the Tuner after you eject a CD. • V/BAR ON [V/BAR OFF] — Displays the Volume Bar at the bottom of the Front Panel while Volume Bar Off turns it off. • INI VOL 15 — Sets the maximum Initial Volume when the unit turns on. Initial Volume sets point of maximum volume when the unit is turned on. If the volume setting was lower than the initial volume setting when the unit is turned off, then the lowe
Inhaltszusammenfassung zur Seite Nr. 12
OPERATION – BASIC PUNCH Remote The Punch button enables the bass and treble response of the audio output to be boosted for all listening levels. 1. Press the PUNCH button to enable the Punch feature. 2. Press the PUNCH button again to disable. NOTE: The panel will display "Punch" when the Punch feature is on. PANEL DISPLAY Tuner Mode: The panel will display the band, FM1, FM2 or AM1, and the station frequency, unless the default has been changed to TITLE DEFAULT and a station title has been prog
Inhaltszusammenfassung zur Seite Nr. 13
OPERATION – TUNER SELECTING A STATION Remote Press the Up or Down Button (SEEK or ) once and the Tuner will rapidly proceed to the next (UP) or pervious (DOWN) station. Press and holding either the Up or Down button (SEEK or ) for 1 second will put you into TUNER MANUAL mode. You can now manually search up or down at a rate of one digit per click (pressing and holding the Up or Down button will allow rapid searching). PRESET BUTTONS Each Tuner mode—FM1, FM2, and AM—has 10 presets for a total of
Inhaltszusammenfassung zur Seite Nr. 14
OPERATION – TUNER PTY MODE KEY Music Mode Speech Mode PTY (Program Type) can search for radio stations via M1 POP M NEWS MUSIC MODE or SPEECH MODE networks. Music Mode M2 ROCK M AFFAIRS categorizes radio stations into Pop, Rock, Modern Music, Light, Classics, and others. Speech Mode categorizes music M3 M.O.R.M. INFO into News, Affairs, Info, Sports, Education, Drama, Culture, M4 LIGHT M SPORT and Science. REG (Region Mode) will switch the station to M5 CLASSICS EDUCATE another that has the sam
Inhaltszusammenfassung zur Seite Nr. 15
OPERATION – CD PLAYER Advanced Operation The following also works with the optional CDX Multi-Disc Changer if it has been installed. NOTE: Items shown in () refer to remote control functions. Track Selection 1. Press the UP button (SEEK ) to select the next track on the disc. 2. Press the DOWN button (SEEK ) to select the previous track. Considerations CDP MODE: The disc will start over at track 1 again after the last track plays. CDX MODE: When the last track number on the current disc is reach
Inhaltszusammenfassung zur Seite Nr. 16
R75 OPERATION – CD PLAYER Pause CD Remote 1. Press the MUTE (Mute/Pause) button to pause the CD. 2. Press the MUTE (Mute/Pause) button a second time to resume playing the disc. NOTE: The panel will display PAUSE and the track number until the function is canceled. Direct Track Access Remote Direct Track Access allows any track to be immediately selected and played. This method is faster than manually cycling through each track on the disc. 1. Press the T-ACC (AS–TRACK ACC) button to select Direc
Inhaltszusammenfassung zur Seite Nr. 17
OPERATION – CD PLAYER CD Changer Mode 1. Press the MODE button until CDX PLAY is displayed. 2. The CD changer will immediately begin playing track #1 of the first available disc. 3. If the changer was previously initialized, the changer will resume playing the last track initialized. Disc Selection Remote 1. Press the PRESET 5–UP button to select the next disc in the magazine. 2. Press the PRESET 4–DOWN button to select the previous disc in the magazine. 3. Press the D-ACC (PTY–DISC-ACC) button
Inhaltszusammenfassung zur Seite Nr. 18
OPERATION – TITLE PROGRAMMING 4. Turn the VOLUME knob to select the proper character. 5. Press the VOLUME knob to move to the next space. 6. Press and hold the VOLUME knob for 1 second to store the title into memory. Title Erasing 1. Press and hold the MUTE button for 1 second. 2. Turn the VOLUME knob to select the title for erasing. 3. Press and hold the VOLUME knob for 1 second to erase the title. OPERATION – MP3 MP3 Player Operation — Basic Playing NOTE: RFX players do not recognize MP3 CDs c
Inhaltszusammenfassung zur Seite Nr. 19
OPERATION – MP3 NOTE: If The song name will remain displayed for 5 seconds in steps 1 through 4 above. If no action is taken during this 5 second period, the display will default back to the song currently playing. 5. Press ENTER to select the song and the song will begin playing. NOTE: If no disc is loaded into the CD player, NO CD will be displayed and the source unit will revert to AUX1* mode, (Tuner Mode if 9110). DOWN Button When playing an MP3 track, pressing the DOWN button will take you
Inhaltszusammenfassung zur Seite Nr. 20
TROUBLESHOOTING NOTE: If the error still continues after doing one of the easy remedies, before taking the unit to a service dealer, try reseting the system by pressing the reset button. General SYMPTOM DIAGNOSIS REMEDY Source Unit does Voltage applied to Red and Check battery, connections and fuses and Yellow wires is not between repair or replace as necessary. If voltage is not turn on 10.8 and 16 volts or there is no above +16 volts, have the electrical system voltage present inspected by an
