Inhaltszusammenfassung zur Seite Nr. 1
SyncMaster 460TMn
LCD Display
User Manual
The color and the appearance may differ depending on the
product, and the specifications are subject to change
without prior notice to improve the performance.
Inhaltszusammenfassung zur Seite Nr. 2
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property dam- age. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Notational Conventions Important to read and under- Prohibited stand at all times Disconnect the plug from the Do not disassemble outlet Ground to preven
Inhaltszusammenfassung zur Seite Nr. 3
Safety Instructions Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product. • Otherwise, this may result in damage to the product due
Inhaltszusammenfassung zur Seite Nr. 4
Safety Instructions Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire. When putting the product down, make sure to put it down softly. • Otherwise, this may result in damage to the screen display. Do not place the front of the product on the floor. • Otherwise, this may result in damage to the screen display. Install your product in a well ventilated location. Ensure that there is a clearance of more than
Inhaltszusammenfassung zur Seite Nr. 5
Safety Instructions Since the product housing is easily scratched, make sure to use the specified cloth only. When cleaning the product, do not spray water directly onto the main body of the product. • Ensure that water does not enter the product and that it is not wet. • Otherwise, this may result in electric shock, fire or a malfunc- tion. Others The product is a high voltage product. Ensure that users do not disassemble, repair or modify the product themselves. • Otherwise, this may result
Inhaltszusammenfassung zur Seite Nr. 6
Safety Instructions • This may result in a product malfunction, electric shock, or fire. Do not use or keep combustible spray or flammable material near the product. • Otherwise, this may result in an explosion or fire. Do not insert any metal, such as chopsticks, coins, pins and steels, or inflammable objects, such as matches or paper, inside the product (through the ventilating openings, input and output terminals, etc). • If water or foreign material enters the product, disconnect the power
Inhaltszusammenfassung zur Seite Nr. 7
Safety Instructions Use only the specified standardized batteries, and do not use a new battery and a used battery at the same time. • Otherwise, the batteries may be damaged or cause fire, per- sonal injury or damage due to a leakage of the internal liquid. The batteries (and rechargeable batteries) is not ordinary refuse and must be returned for recycling purposes. The customer is re- sponsible for returning the used or rechargeable batteries for recycling purposes as the consumer. • The cust
Inhaltszusammenfassung zur Seite Nr. 8
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking LCD Display Manuals Quick Setup Guide Warranty Card User's Guide (Not available in all loca- tions) MagicInfo Software CD, MagicInfo Manual CD Others Remote Control Batteries (AAA X 2) GND Cable 7
Inhaltszusammenfassung zur Seite Nr. 9
Introduction Others (Not available in all loca- tions) Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values. When OSD is not on the screen, push the b
Inhaltszusammenfassung zur Seite Nr. 10
Introduction Note • This is available when a TV tuner box is installed. Note • This function does not work for this LCD Display. Power button [ ] Use this button for turning the LCD Display on and off. Brightness Sensor The product's Brightness Sensor function automatically detects the sur- rounding brightness using a brightness sensor and adjusts its brightness accordingly. Power indicator Shows PowerSaver mode by blinking green Note See PowerSaver described in the manual for further informa
Inhaltszusammenfassung zur Seite Nr. 11
Introduction POWER S/W ON [ │ ] / OFF [O] Switches the LCD Display On/Off. POWER IN The power cord plugs into the LCD Display and the wall plug. HDMI IN Connect the HDMI terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI ca- ble. Up to HDMI cable 1.0 can be supported. LAN (LAN Connection Terminal) USB(USB Connection Terminal) Keyboard / Mouse, Mass Storage Device Compatible. AUDIO OUT Headphone/External speaker output termi- nal.
Inhaltszusammenfassung zur Seite Nr. 12
Introduction Side 1. Connect the GND wires to the bottom part of both sides of the product and then to the back of the product as shown by figure ( ). 2. Connect the other side of the GND wires to the ground box when indoors or to the ground pole that has been pushed into the ground when outdoors. Note The ground (GND) is used to prevent product noise and to protect people from electric shock due to electric leakage. Remote Control Note The performance of the remote control may be affected by
Inhaltszusammenfassung zur Seite Nr. 13
Introduction POWER OFF Number Buttons DEL button + VOL - MUTE TV/DTV MENU INFO COLOR BUTTONS TTX/MIX STILL AUTO S.MODE MDC LOCK SOURCE ENTER/PRE-CH CH/P D.MENU GUIDE RETURN Up-Down Left-Right buttons EXIT SRS MagicInfo P.MODE DUAL/MTS PIP SWAP Turns the product On. 1. POWER Turns the product Off. 2. Off 3. Number Buttons Press to change the channel. The "-" button operates only for DTV. It is used to select 4. DEL button MMS (multi-channel) for a DTV. 12
Inhaltszusammenfassung zur Seite Nr. 14
Introduction 5. + VOL - Adjusts the audio volume. Pauses (mutes) the audio output temporarily. This is dis- 6. MUTE played on the lower left corner of the screen. The audio resumes if MUTE or - VOL + is pressed in the Mute mode. 7. TV/DTV Selects the TV and DTV mode directly. 8. MENU Opens the on-screen menu and exits from the menu or closes the adjustment menu. Activates a highlighted menu item. 9. Current picture information is displayed on the upper left 10. INFO corner of the screen. 11.COLO
Inhaltszusammenfassung zur Seite Nr. 15
Introduction Returns to the previous menu. 23. RETURN 24. Up-Down Left-Right but- Moves from one menu item to another horizontally, vertically tons or adjusts selected menu values. Exits from the menu screen. 25. EXIT Selects SRS TruSurround XT mode. 26. SRS 27.MagicInfo MagicInfo Quick Launch Button. 28. P.MODE When you press this button, current picture mode is dis- played on the lower center of the screen. AV / HDMI / TV : P.MODE The LCD Display has four automatic picture settings that are pr
Inhaltszusammenfassung zur Seite Nr. 16
Using the Software Touch Screen 1. Double-click "Calibrate" on the Desktop. Right-click over the icon in the system tray and select "Calibrate" from the pop-up menu. When the points are displayed, touch the corresponding points exactly. Note Since you may not be able to touch a point located at the edge, connect and use a mouse. 15
Inhaltszusammenfassung zur Seite Nr. 17
Adjusting the LCD Display Input Source List MENU → ENTER → [Input] → ENTER → [Source List] → , → ENTER 1. HDMI 2. MagicInfo Note • The direct button on the remote control is the 'SOURCE' button. Edit Name MENU → ENTER → [Input] → → ENTER → [Edit Name] → , → ENTER Name the input device connected to the input jacks to make your input source selection easier. VCR / DVD / Cable STB / HD STB / Satellite STB / AV Receiver / DVD Receiver / Game / Camcorder / DVD Combo / DHR / PC Picture MagicBrig
Inhaltszusammenfassung zur Seite Nr. 18
Adjusting the LCD Display → , → ENTER MagicBright is a feature providing the optimum viewing environment depending on the con- tents of the image you are watching. Currently four different modes are available: Entertain, Internet, Text and Custom. Each mode has its own pre-configured brightness value. You can easily select one of the four settings by simply pressing the MagicBright control button. (Not available in Dynamic Contrast mode of On.) 1. Entertain High brightness For watching motion
Inhaltszusammenfassung zur Seite Nr. 19
Adjusting the LCD Display → , → ENTER Adjusts the Contrast. Brightness MENU → → ENTER → [Picture] → → ENTER → [Custom] → → ENTER → [Bright- ness] → , → ENTER Adjusts the Brightness. Sharpness MENU → → ENTER → [Picture] → → ENTER → [Custom] → → → ENTER → [Sharpness] → , → ENTER Adjusts the Sharpness. Color Tone MENU → → ENTER → [Picture] → → →ENTER → [Color Tone] → , → ENTER The color tones can be changed. (Not available in Dynamic Contrast mode of On.) 1. Off 2. Cool 3. Normal 4.
Inhaltszusammenfassung zur Seite Nr. 20
Adjusting the LCD Display If you set the Color Tone to Off, the Color Control function is disabled Color Control Note • This function does not work for this LCD Display. Adjusts individual Red, Green, Blue color balance. MENU → → ENTER → [Picture] → → → → ENTER → [Color Control] (Not available in Dynamic Contrast mode of On.) Note If you adjust the picture by using the Color Control function, Color Tone will turn to the Cus- tom mode. Red MENU → → ENTER → [Picture] → → → → ENTER → [Color
